Tech / General Engine Is your car making a strange sound or won't start? Thinking of adding power with a new combination? Need other technical information or engine specific advice? Don't see another board for your problem? Post it here!

engine balancing

Thread Tools
 
Search this Thread
 
Old 03-06-2007, 02:31 PM
  #1  
Member

Thread Starter
iTrader: (2)
 
Blake's Avatar
 
Join Date: Feb 2004
Location: okotoks Alberta
Posts: 412
Likes: 0
Received 0 Likes on 0 Posts
Car: 1991 Camaro RS
Engine: 406ci
Transmission: T-56 LT1
Axle/Gears: 3.42
engine balancing

i'm guilding a sbc 400

wondering if its imparative to balance the engine internals?

the crank is a scat 9000
forged scat i beam rods
forged flat top srp pistons

also what does it mean when they say internally balanced and externally?

I've always been lead to believe that they wouuld add weight or take weight away from the flywheel or balancer if externally balanced,

and if internally balanced, from the crank shaft etc

cheers

blake
Old 03-06-2007, 02:45 PM
  #2  
Moderator

 
Apeiron's Avatar
 
Join Date: Jan 2000
Location: Mercedes Norte, Heredia, Costa Rica
Posts: 20,981
Likes: 0
Received 9 Likes on 8 Posts
Car: 1984 Z28 Hardtop
Engine: 383 Carb
Transmission: 4L60
Axle/Gears: 3.54 Dana 44
A rotating assembly with a new crank should be balanced.

Internally balanced means all the weight necessary to balance the rotating assembly is located on the counterweights inside the engine, and the flywheel and damper are neutrally balanced.

Externally balanced means that some of the balancing weight is located outside the engine on the flywheel and damper. The flywheel and balancer themselves don't have to be altered from their stock specs.
Old 03-06-2007, 02:48 PM
  #3  
Member
 
Tranny's Avatar
 
Join Date: May 2005
Location: Goose Creek, SC
Posts: 107
Likes: 0
Received 0 Likes on 0 Posts
Car: 87 Trans Am
Engine: 434 being built
Transmission: 700R4
Axle/Gears: 3:73
I was told...

I was told that the old 400 cranks weren't balanced so they did it by special dampers. But if you buy a internal balanced crank then you can go with internal balanced parts. I would still have all the parts balanced together before you build the engine.
Old 03-06-2007, 03:09 PM
  #4  
Moderator

 
Apeiron's Avatar
 
Join Date: Jan 2000
Location: Mercedes Norte, Heredia, Costa Rica
Posts: 20,981
Likes: 0
Received 9 Likes on 8 Posts
Car: 1984 Z28 Hardtop
Engine: 383 Carb
Transmission: 4L60
Axle/Gears: 3.54 Dana 44
When GM made the 400, they weren't comfortable putting a 5.7" rod in it, because this would have raised the wrist pin too high, so they used a 5.454" rod instead. Shortening the rod meant there wasn't enough clearance to put large enough counterweights in to balance it internally, so they put the weight on the damper and flywheel.

A 400 can be internally balanced though, by using a longer rod with an aftermarket crank and pistons, or by adding heavy and expensive Mallory metal to the counterweights.
Old 03-07-2007, 05:09 PM
  #5  
Member
 
Tranny's Avatar
 
Join Date: May 2005
Location: Goose Creek, SC
Posts: 107
Likes: 0
Received 0 Likes on 0 Posts
Car: 87 Trans Am
Engine: 434 being built
Transmission: 700R4
Axle/Gears: 3:73
good

I am putting together a 434. I've had the mains spayed and went with the Eagle esp "H" beam rods and crank. This should really stroke!
Old 03-07-2007, 05:29 PM
  #6  
Supreme Member
 
SpitotRs305's Avatar
 
Join Date: Oct 2006
Posts: 1,974
Likes: 0
Received 0 Likes on 0 Posts
Car: 91 RS
Engine: 350 vortec
Transmission: T-5
Axle/Gears: not the best not the worst
have your mains spayed or neutured this is bob barker saying soo long
Old 03-07-2007, 05:59 PM
  #7  
Moderator

 
Apeiron's Avatar
 
Join Date: Jan 2000
Location: Mercedes Norte, Heredia, Costa Rica
Posts: 20,981
Likes: 0
Received 9 Likes on 8 Posts
Car: 1984 Z28 Hardtop
Engine: 383 Carb
Transmission: 4L60
Axle/Gears: 3.54 Dana 44
Racing engines should never have their mains spayed as it tends to reduce their aggressive tendancies and makes them prone to sitting in the driveway getting fat and lazy.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
midge54
LTX and LSX
21
12-27-2019 04:14 PM
italiano67
Tech / General Engine
8
12-11-2016 09:21 AM
LT1Formula
Engine/Drivetrain/Suspension Parts for Sale
10
11-16-2015 01:13 PM
InfinityShade
Transmissions and Drivetrain
15
08-22-2015 08:00 PM
bradleydeanuhl
DFI and ECM
4
08-12-2015 11:48 AM



Quick Reply: engine balancing



All times are GMT -5. The time now is 12:52 AM.