Need help feeding gauge wires through firew
#1
Junior Member
Thread Starter
Join Date: Aug 2011
Location: Atlanta, Ga
Posts: 68
Likes: 0
Received 0 Likes
on
0 Posts
Car: 82 Firebird/ 79 Camaro Berlinetta
Engine: 151 Pontiac Iron Duke TBI/ 305 SBC
Transmission: THM200/ THM200r4
Axle/Gears: 2.93/ 2.41
Need help feeding gauge wires through firew
Im installing a gauge pod for my firebird while i change the head gasket, problem is I dont know where i should feed everything through my dash through to fire wall to the block pictures or anything will be gratefully appreciated
Thank you
Thank you
#2
Junior Member
Join Date: Sep 2011
Location: Strasburg, Pennsylvania
Posts: 46
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Chevrolet Camaro Z/28 (Project
Engine: 5.0L 305
Transmission: 700R4 W/ B&M shift kit
Axle/Gears: 3.23
Re: Need help feeding gauge wires through firew
Im not sure how similar firebirds are but on my camaro there was a hole for wires behind the steering column. i would pull the panel to expose the whole thing and there should be wires going into the fire wall and you can always add holes
#3
Junior Member
Thread Starter
Join Date: Aug 2011
Location: Atlanta, Ga
Posts: 68
Likes: 0
Received 0 Likes
on
0 Posts
Car: 82 Firebird/ 79 Camaro Berlinetta
Engine: 151 Pontiac Iron Duke TBI/ 305 SBC
Transmission: THM200/ THM200r4
Axle/Gears: 2.93/ 2.41
Re: Need help feeding gauge wires through firew
Thanks man ill take a look at it once this weathers clears down here, which panel exactly you were talking about, before I go in there?
#4
Junior Member
Join Date: Sep 2011
Location: Strasburg, Pennsylvania
Posts: 46
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Chevrolet Camaro Z/28 (Project
Engine: 5.0L 305
Transmission: 700R4 W/ B&M shift kit
Axle/Gears: 3.23
Re: Need help feeding gauge wires through firew
there should be a panel that comes off it has a door to pop on to get to the fuses at least on thats how it set up on camaro but ill try to upload a picture of it
#5
Junior Member
Thread Starter
Join Date: Aug 2011
Location: Atlanta, Ga
Posts: 68
Likes: 0
Received 0 Likes
on
0 Posts
Car: 82 Firebird/ 79 Camaro Berlinetta
Engine: 151 Pontiac Iron Duke TBI/ 305 SBC
Transmission: THM200/ THM200r4
Axle/Gears: 2.93/ 2.41
Re: Need help feeding gauge wires through firew
Sorry for a late response, I actually took most of my dash apart the other day and it turns out ill most likely be needing to drill a whole for the wires and etc maybe there is a whole some where im just not gettin a good view of it from either side of the firewall
#6
Junior Member
Join Date: Sep 2011
Location: Strasburg, Pennsylvania
Posts: 46
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Chevrolet Camaro Z/28 (Project
Engine: 5.0L 305
Transmission: 700R4 W/ B&M shift kit
Axle/Gears: 3.23
Re: Need help feeding gauge wires through firew
keep me updated on that i think maybe someday after i drop a bigger engine in mine i may do guages to replace the old ones
Thread
Thread Starter
Forum
Replies
Last Post
Ghettobird52
Tech / General Engine
15
12-29-2023 08:23 AM