Advice needed please
#1
Member
Thread Starter
iTrader: (1)
Join Date: Feb 2007
Location: Toronto
Posts: 222
Likes: 0
Received 0 Likes
on
0 Posts
Car: 84 Z28
Engine: 350
Transmission: 700R4
Advice needed please
I recently did the intake gasket on my 350 chev, today I ran the car for an hour or so and noticed oil building up around the intake on both sides on the manifold gasket, at fist I thought maybe oil was running down from the valve cover gasket but it is not, I used sealant on the bolts when installing also, they are edlebrock rpm aluminum heads and intake with ARP bolts is it possible I didn't torque it down enough? I torqued it to 20ftp...
#2
Supreme Member
Join Date: Mar 2009
Location: Sussex County, NJ
Posts: 1,402
Likes: 0
Received 3 Likes
on
3 Posts
Car: 1994 Z28
Engine: 355 LT1
Transmission: T56
Axle/Gears: 3.42
Re: Advice needed please
What about around the distributor? Do you have a gasket there? Try to whipe it all down and pinpoint what is leaking.
#3
Member
Thread Starter
iTrader: (1)
Join Date: Feb 2007
Location: Toronto
Posts: 222
Likes: 0
Received 0 Likes
on
0 Posts
Car: 84 Z28
Engine: 350
Transmission: 700R4
Re: Advice needed please
Yes there is a gasket there, I'm certain the oil is coming from the intake gasket i pulled a vavle cover and was dry, but I'm not sure if its because its torqued wrong... The oil is seeping from the intake manifold gaskets only on the sides the front and back is dry
#4
Supreme Member
Join Date: Mar 2009
Location: Sussex County, NJ
Posts: 1,402
Likes: 0
Received 3 Likes
on
3 Posts
Car: 1994 Z28
Engine: 355 LT1
Transmission: T56
Axle/Gears: 3.42
Re: Advice needed please
Did you torque the intake in the correct sequence? I'm pretty sure intake bolts get torqued to 18lbs and the sequence is something like center 4 then 1 back opposite side then repeat on front. I'd imagine you'd have a pretty nasty vacuum leak if the intake wasn't sealed (usually resulting in one bank of plugs being rich and one side lean) so the only other option is your bolts are leaking.
Trending Topics
#8
Member
Thread Starter
iTrader: (1)
Join Date: Feb 2007
Location: Toronto
Posts: 222
Likes: 0
Received 0 Likes
on
0 Posts
Car: 84 Z28
Engine: 350
Transmission: 700R4
Re: Advice needed please
Vacuum is pulling just under 15, car starts and idles fine, what should the torque be for this application? Thanks
#9
Supreme Member
iTrader: (1)
Join Date: Sep 2005
Posts: 26,150
Received 1,692 Likes
on
1,286 Posts
Car: Yes
Engine: Usually
Transmission: Sometimes
Axle/Gears: Behind me somewhere
Re: Advice needed please
20 ft-lbs is fine. The "spec" is probably closer to 30, being as how the hardware is that size; but 20 is entirely adequate.
Pull the 2 center bolts on each side, one at a time. Wire-brush whatever you put on the threads, off. Clean out the hole threads with a tap. Use some spray carb cleaner on both the bolts and the holes. Re-install them using the Permatex "high-temp thread sealer with Teflon". Use plenty. Make sure there's some under the head of the bolt.
The 2 at each end on each side are blind; only the center 2 on each side go through to the crankcase. So you don't have to do that to those other 8, only the center 4.
Check them all and make sure they're tight though, otherwise your next post is likely to be "I have water seeping out at the ends of the intake".
Pull the 2 center bolts on each side, one at a time. Wire-brush whatever you put on the threads, off. Clean out the hole threads with a tap. Use some spray carb cleaner on both the bolts and the holes. Re-install them using the Permatex "high-temp thread sealer with Teflon". Use plenty. Make sure there's some under the head of the bolt.
The 2 at each end on each side are blind; only the center 2 on each side go through to the crankcase. So you don't have to do that to those other 8, only the center 4.
Check them all and make sure they're tight though, otherwise your next post is likely to be "I have water seeping out at the ends of the intake".
Thread
Thread Starter
Forum
Replies
Last Post