Which Converter to choose
#1
Member
Thread Starter
iTrader: (2)
Join Date: Dec 2002
Location: Lincoln, NE
Posts: 188
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1988 GTA
Engine: 350 TPI
Transmission: TH350
Which Converter to choose
Right now i'm looking at getting either the TCI Streetfighter converter or the B&M 3000 Holeshot converter. Would like to here some people's opinions on these converters. Or if there is any other converters out there around 3000 stall for relitivily cheap.
Thanks
Thanks
#3
Supreme Member
Join Date: Jul 1999
Location: Calimesa, California, U.S.
Posts: 3,458
Likes: 0
Received 39 Likes
on
27 Posts
First, "stay away" from B&M, their comeback/failure rate is very high, TCI is a "little" better. Second, if you want a stall that is over 2,200 rpm, I would advise against using a 12" stock diameter torque converter. Anything over 2,200 rpm starts to drop the torque multiplication, create more heat, are slippery feeling, etc. You will have to spend some money if you want to do this right.
#4
Supreme Member
Join Date: Sep 2001
Location: Flowery Branch, GA
Posts: 1,195
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 Iroc-Z
Engine: 1 BA 305 TPI
Transmission: Probuilt 700R4 - 2800 Stall Midwest
Axle/Gears: 3.42
Re: re
Originally posted by 90formula5.7
try midwest convertors, i have one of their 91/2 " 3200 stall convertors. i have had no problems yet!!
try midwest convertors, i have one of their 91/2 " 3200 stall convertors. i have had no problems yet!!
#5
Does midwest have a website? I have a dayco 2300-2500 rpm stall and havent had any problems, I think it was about $260, but i was thinking about a 2800-3000 rpm stall to get a quicker time...eh?
#6
Member
iTrader: (1)
Join Date: May 2003
Location: tyler
Posts: 168
Likes: 0
Received 0 Likes
on
0 Posts
Car: cobalt ss/sc, 91 z28, 92 z28
Engine: 385 stroker
Transmission: 700r4
Axle/Gears: stock 10 bolt 3.73
pro built im not sure on what u r saying i got the breakaway tci converter for my setup i was told by jegs and summit that it was a 3000 stall lockup converter aint that right? and about it being 12 inches i think it is about that 12 inches or it could be 11 not sure can i get some info on that please thanks!
#7
Supreme Member
Join Date: Jul 1999
Location: Calimesa, California, U.S.
Posts: 3,458
Likes: 0
Received 39 Likes
on
27 Posts
The "cheap" way to get a stall (2,200 rpm & higher) is to use the 12", and lockup only. They get slippery, produce more heat, are inefficent, etc. An 11" would be a little better, but 2,400 - 2,500 rpm would be maximum if you want good driveability. There is no good way around this. 10" or 9.5" is the way to go if you want to do this right.
Last edited by Pro Built Automatics; 07-13-2003 at 07:45 PM.
Trending Topics
#8
Supreme Member
Join Date: Sep 2001
Location: Flowery Branch, GA
Posts: 1,195
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 Iroc-Z
Engine: 1 BA 305 TPI
Transmission: Probuilt 700R4 - 2800 Stall Midwest
Axle/Gears: 3.42
Originally posted by z86roc28
Does midwest have a website? I have a dayco 2300-2500 rpm stall and havent had any problems, I think it was about $260, but i was thinking about a 2800-3000 rpm stall to get a quicker time...eh?
Does midwest have a website? I have a dayco 2300-2500 rpm stall and havent had any problems, I think it was about $260, but i was thinking about a 2800-3000 rpm stall to get a quicker time...eh?
Thread
Thread Starter
Forum
Replies
Last Post
Thirdgen89GTA
NW Indiana and South Chicago Suburb
4
11-26-2015 11:04 PM