I NEED HELP FINDING GEARS
#1
Junior Member
Thread Starter
Join Date: Jan 2011
Location: jacksonville nc
Posts: 16
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1988 IROC-Z ,1991 RS
Engine: 350 TPi , 305 TBI
Transmission: 700r4 ,t56 sixspeed
Axle/Gears: ?
I NEED HELP FINDING GEARS
HAY GUYS I AM LOOKING FOR A SET OF GEARS FOR MY 88 IROC Z IT IS AND DANA 44 DISK BRAKE REAR END AND IT WAS FACTORY IN THE CAR BUT I AM TRYING TO FIND A SET OF 4:10 GEARS FOR HERE CANT GET MY 60 FOOT TIME DOWN AT THE TRACK RUNNING 95 TO 97 MPH THROW THE TRAPS AND ONLY RUNNING 15 TO 15,5 HELP PLEZ I NEED HELP
#2
Guest
Posts: n/a
Re: I NEED HELP FINDING GEARS
Sort of like this?
http://www.ringpinion.com/ProductDet..._Standard_Gear
This may not be the correct part number, because look here:
http://www.ringpinion.com/DiffList.a...pe=Dana_Spicer
look how many variations they're showing for the D44!
But you say it's a stock 88? Then it's probably the 9-bolt, not a Dana.
http://www.ringpinion.com/DiffDetail...2+Borg+Warner+
If so, it's 3.73:1 or swap to a different axle.
http://www.ringpinion.com/ProductDet..._Standard_Gear
This may not be the correct part number, because look here:
http://www.ringpinion.com/DiffList.a...pe=Dana_Spicer
look how many variations they're showing for the D44!
But you say it's a stock 88? Then it's probably the 9-bolt, not a Dana.
http://www.ringpinion.com/DiffDetail...2+Borg+Warner+
If so, it's 3.73:1 or swap to a different axle.
Last edited by ronnjonn; 05-27-2011 at 01:05 AM.
#3
Supreme Member
iTrader: (14)
Join Date: Aug 2006
Location: Central NJ
Posts: 12,650
Likes: 0
Received 44 Likes
on
42 Posts
Car: 86 Trans Am, 92 Firebird
Engine: 408 sbc, 3.1L of raw power
Transmission: TKO600, T5
Axle/Gears: Moser 9", 3:70 trutac, 3:23 torsion
Re: I NEED HELP FINDING GEARS
a dana44 was never factory installed in any 3rd gen, they were only installed in the firehawks (91-92), built by SLP, and available over the counter by GM.
If it is a dana 44 is was swapped in at some point.
ifs its indeed the original axle, are you sure its not a 9 bolt?
If it is a dana 44 is was swapped in at some point.
ifs its indeed the original axle, are you sure its not a 9 bolt?
#4
Junior Member
Thread Starter
Join Date: Jan 2011
Location: jacksonville nc
Posts: 16
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1988 IROC-Z ,1991 RS
Engine: 350 TPi , 305 TBI
Transmission: 700r4 ,t56 sixspeed
Axle/Gears: ?
Re: I NEED HELP FINDING GEARS
i know it has been a really long time. i have found out by calling slp found out it is an Aulstralian 9 bolt. and have only found one place to get gears it looks like almost 900 for gears and a carrier. so i have been looking for a 4 gen 10 bolt rear cheap i live in jacksonville nc seeing if there was any thing close to the area
Thread
Thread Starter
Forum
Replies
Last Post
junkcltr
Tech / General Engine
6
08-02-2019 11:12 PM
ambainb
Camaros for Sale
11
04-25-2016 09:21 PM
lt1z350
Engine/Drivetrain/Suspension Parts for Sale
3
09-29-2015 01:50 PM