Hey Orr, I got my Zexel!
#1
Senior Member
Thread Starter
Join Date: Apr 2006
Location: Pgh PA
Posts: 835
Received 0 Likes
on
0 Posts
Car: 89 5.7 IROC/95 LT1 Corvette
Engine: All 5.7's
Transmission: 700R4 (Roessler)/ZF6
Axle/Gears: 10 bolt Zexel 3.23's. CTW 17" wheel
Hey Orr, I got my Zexel!
It came with 3.23 gears. I have an earlier F body 10 bolt case. I plan on getting the direct fit axles (28 spline) from summit for a 91-92 10 bolt, new bearing kit and the brake conversion kit from Bynfly soon. is there anything else I need? Thanks!
#2
Re: Hey Orr, I got my Zexel!
Be sure that you get the installation kit with the Super Shim set and Timken bearings. The Ratech shims are a real pain in the rear. Randy's Ring & Pinion, Tom's Differentials and DTS have the kits with the good shims.
#4
Senior Member
Thread Starter
Join Date: Apr 2006
Location: Pgh PA
Posts: 835
Received 0 Likes
on
0 Posts
Car: 89 5.7 IROC/95 LT1 Corvette
Engine: All 5.7's
Transmission: 700R4 (Roessler)/ZF6
Axle/Gears: 10 bolt Zexel 3.23's. CTW 17" wheel
Re: Hey Orr, I got my Zexel!
C clip eliminators?
#6
Re: Hey Orr, I got my Zexel!
I don't recommend c clip eliminators for a street car, especially one that will be used for hard cornering. They should be considered for drag race only.
#7
Senior Member
Thread Starter
Join Date: Apr 2006
Location: Pgh PA
Posts: 835
Received 0 Likes
on
0 Posts
Car: 89 5.7 IROC/95 LT1 Corvette
Engine: All 5.7's
Transmission: 700R4 (Roessler)/ZF6
Axle/Gears: 10 bolt Zexel 3.23's. CTW 17" wheel
Re: Hey Orr, I got my Zexel!
Copy that, they don't work with disk brakes anyways. Thanks. Summit kits don't specify Timken bearings, I'll check out your recommendations. Thanks again.
Trending Topics
#8
Senior Member
Thread Starter
Join Date: Apr 2006
Location: Pgh PA
Posts: 835
Received 0 Likes
on
0 Posts
Car: 89 5.7 IROC/95 LT1 Corvette
Engine: All 5.7's
Transmission: 700R4 (Roessler)/ZF6
Axle/Gears: 10 bolt Zexel 3.23's. CTW 17" wheel
Re: Hey Orr, I got my Zexel!
Any recommendations on fluid for the Zexel? I won't need a "slip modifier" or additive, correct?
#11
Senior Member
Thread Starter
Join Date: Apr 2006
Location: Pgh PA
Posts: 835
Received 0 Likes
on
0 Posts
Car: 89 5.7 IROC/95 LT1 Corvette
Engine: All 5.7's
Transmission: 700R4 (Roessler)/ZF6
Axle/Gears: 10 bolt Zexel 3.23's. CTW 17" wheel
Re: Hey Orr, I got my Zexel!
Groovy. Thanks.
#14
Re: Hey Orr, I got my Zexel!
Yes, the Richmond kit has the Ratech shims. ALL of the kits that Summit sells have the cheap Ratech shims. You can not get the good shims from Summit or Jeg's.
#15
Senior Member
Thread Starter
Join Date: Apr 2006
Location: Pgh PA
Posts: 835
Received 0 Likes
on
0 Posts
Car: 89 5.7 IROC/95 LT1 Corvette
Engine: All 5.7's
Transmission: 700R4 (Roessler)/ZF6
Axle/Gears: 10 bolt Zexel 3.23's. CTW 17" wheel
Re: Hey Orr, I got my Zexel!
Thanks for all the advice Gentlemen! All parts are ordered and inbound! I went with Summit for the axles, Randy's R&P for the kit and timken bearings and Ed at FlyNbye for brake brackets! I will have Posi for my first event!
Thread
Thread Starter
Forum
Replies
Last Post