I found the new cool 5 star corbra wheels for 125 a pice. I want that style, will they fit my car?


Thanks

------------------
1992 Z28 5.7 TPI 700R-4
------------------
STREET LETHAL
--Drag Racing--

 

BLASPHEMY!!!!(sp?) Ford and Chevy doesnt mix =)

 

ford and chevy mix fine man. If you have a ford and you install chevy parts you are fixing the car. why do you think the ford guys are so quick to drop a chevy motor in their cars.

------------------
90 iroc l98
last season best corected 13.62 @102
mods
full exhaust, AFPR, pulley, jet stage 1 chip, billet servo, 52mm throttle body and a few other little things.

 

Good question... No one makes a really nice aftermarket wheels for third-gens. Some one let me know.. I've been changing my mind daily on what to do for wheels

------------------
92 Z28 - 5.7 - Black/Grey Leather
Macewen White Faced Guages
SLP T-RAM, 24lb/h Injectors
Accell 52mm Throttle Body
SLP 1 3/4" Headers and Cat Back Sys.

Check out the T-Ram at my website:
http://www.mylecdekmat.com/mike.htm

 

Well, anyone? Do I need spacers, or will they bolt right up?

 

I don't even know the bolt pattern. If you know they'll bolt on - I'm sure you can get some spacers milled for a little coin...

I still wish someone would answer this, I think they are scared to give you the OK to put Crustang wheels on your car

 

I thought the ford bolt pattern was only 4 lugs. Why not look for some 17x9.5 used vette rims. You will then need wheel adapters for them ,like I did. Ford is good for 1 thing, 9inch rears!

 

The Mustang finally cahnged to 5 lugs in '96 I believe. I'd like Corvette GS wheels, but I'd like to see them first.

 

I just sold some SS wheels, because I cannot afford spacers or 17" tires. I want the corbra 16" wheels, and I am hoping I don't need spacers.

Does anyone know?
Will they fit?

Ford is now good for 2 things, 9" rear and corbra wheels. Those wheels look so dam good

------------------
1992 Z28 5.7 TPI 700R-4
------------------
STREET LETHAL
--Drag Racing--

 

rustangs changed their bolt pattern in 94 to five lug. trust me i used to be a mustang lover. now i am born again. but far as i knwo the bolt pattern even though it is 5 lug wont fit on our cars. we have a screwed up bolt pattern atleast that is what ever tire place has told me. that is all i know

------------------
1988 firebird formula350tpi msd 6al box blaster 3 coil accel 8.8 wires flowmaster cat back pro shift light a pillar gauge pod and water temp and air/fuel ratio gauges b&m mega console shifter, march underdrive pullies, tpis airfoil
best 1/4 mile run of 14.44@ 96.53

 

Here really soon, I'm going to be putting on GTA rims on my Iroc. Tell me what you think. Do you think it would look alright onmy car? Go to http://members.aol.com/rmacewen1
then go to customers' rides and find the 1990 Iroc, It's red and it has a hyperlink of my name, Brandon Alyea.



------------------
"Clear your mind, relax, and float downstream."

 

JEG's says 5.95" backspacing on them,,, dunno about the bolt pattern spacing tho,,,


p.o.s. Camaro with GTA wheels
if that didn't work,,, http://anzwers.org/free/gta/pos/index.html

------------------
<A HREF="http://anzwers.org/free/gta" TARGET=_blank>87 Firebird
84 Camaro</A>

[This message has been edited by deadbird (edited September 20, 2000).]

 

possibly....when I was looking around at wheels I found http://www.performancewheeloutlet.com/ which has wheels for vettes, stangs, camaros and TAs...If you look under the corvette section they have a wheel called "milan" I believe which appears to be the cobra-r wheel renamed for chevy owners...it says it fits vettes, camaros and TAs, which probably means 4th gens, which means you would need spacers? Under the mustang section they have the same wheel but called cobra-r wheels and they say they fit ford products.

yay! 100 posts

[This message has been edited by TwicK91 (edited September 22, 2000).]

 

Just to anwser my own question, they will not fit, unless I get spacers. Thanks everyone. Performance wheel outlet e-mailed me and said no, they will not fit.

That sucks, how about www.americaneaglewheel.com
two-pice #203?????

------------------
1992 Z28 5.7 TPI 700R-4
------------------
STREET LETHAL
--Drag Racing--

 

Check out www.groupawheels.com. I ordered some 17x9" wheels that have the skinny five spoke design to show off your rotors. i have had MANY, MANY compliments on them since the day I bought them. Go to the ROH section and look down the list of wheels. The Snyper style would probably be the thing you're looking for if you like the cobra wheels. And if you don't want 17", I believe they have 16" available.

------------------
"So,tell me Mr. Stang. How's life like living in the exhaust of a Chevy V-8?"
-------------------------
'91 RS 5.0 TBI
New paint-solid black
ROH Snyper wheels-17x9 wrapped in 275/40/17
Eibach sportline springs
Flowmaster cat-back
TBI mods
MANY more to come!!!!

[This message has been edited by RSpeed (edited September 22, 2000).]

 

You shouldn't want a Ford product on your Chevy car..... 'nuff said

------------------
1989 IROC-Z
350c.i. TPI
rebuilt 700R4 with shift kit
3'' Monza Pacesetter cat back exhaust (minus the muffler)[SOUNDS OF THIS ON MY WEBPAGE]
new dual cats
3.23 Posi rear
hypertech chip
under drive pulleys
adjustable fuel pressure regulator
K&N Air Filters
Excalibur alarm, keyless entry and remote start
new:
struts, shocks, bearings, distributor, cap, rotor, alternator, battery, regulator
245 ZR16 50 Tires, Rotors and brake pads all the way around

Go to my webpage to find out more about it.
You can also see pictures, and hear sounds as well.
http://go.to/iroc-z

AOL IMer: JRShotliff

 

I should not want a Ford product on my car? WTF????????
If it looks good, you can't deniy it!
Just because we compeat with Ford mustangs, does not mean their wheels suck?

I happen to know alot of mustangs out their that look good and run good.

Now I am a BIG GM fan, but their is nothing wrong with the Ford Mustangs.

Why would I not put it on my car? Unless Ford wheels have a bad habbit of breaking, then I could see everyones point, but they are good looking wheels (they look just as good if not better than the SS AND WS6 wheels) so I don't care if it's Ford or GM.

Nuff said

------------------
1992 Z28 5.7 TPI 700R-4
------------------
STREET LETHAL
--Drag Racing--

 

I would imagine an expensive way to convert to the Pusstang wheels, which I happen to like also, would be to get custom hubs made. Like if you were to get Baer brakes have them drill the set for Ford bolt pattern, and for the rear get some axels drilled for ford also. It would be really expensive but it is just a suggestion. Oh and I absolutely HATE Mustangs but the wheels look ok.

James

------------------
If the women don't find you handsome they should at least find you handy

 

I was thinking of the same thing
I loved those wheels ever since I saw them on the 'Stang in Summit!
If you find anything out about fitting a 3rd. Gen., let me know.
Thanks,
Gary

------------------
Click Here!

[This message has been edited by NECC (edited October 03, 2000).]