New Camaro Hurst Shift Knob
Thread Starter
Junior Member
Joined: Jun 2000
Posts: 37
Likes: 0
From: Santa Barbara, CA, USA
New Camaro Hurst Shift ****
Hey guys, I was wondering if a 1996+ Camaro SS/Firehawk Hurst Shift **** would fit my 86 IROC T-5?? Like do they share the same threads and shaft size and everything?? Thanks
TGO Supporter
iTrader: (2)
Joined: Jul 1999
Posts: 13,579
Likes: 9
From: Readsboro, VT
Car: 85 IROC-Z / 88 GTA
Engine: 403 LSx (Pending) / 355 Tuned Port
Transmission: T56 Magnum (Pending) / T5
Axle/Gears: 3.42 / ?
I was wondering this too. My GTA needs a new **** and I've been looking at the WS6 **** from RK Sport.
------------------
The IROC Homepage
<A HREF="http://www.rit.edu/~jli4307/camaro" TARGET=_blank>
View the restoration of an 85 IROC</A>
"I didn't know a bored out Ford could go so slow" -Shenandoah
------------------
The IROC Homepage
<A HREF="http://www.rit.edu/~jli4307/camaro" TARGET=_blank>
View the restoration of an 85 IROC</A>
"I didn't know a bored out Ford could go so slow" -Shenandoah
Supreme Member
Joined: Mar 2000
Posts: 1,160
Likes: 1
From: Lexington, SC
Car: 1992 Z/28, 2000 SS, 1968 RS/SS
Engine: 355 Built a bit / LS1
Transmission: T-5 / A4
Axle/Gears: 4.10 / 2/73's
<font face="Verdana, Arial" size="2">Originally posted by 86IROC:
Hey guys, I was wondering if a 1996+ Camaro SS/Firehawk Hurst Shift **** would fit my 86 IROC T-5?? Like do they share the same threads and shaft size and everything?? Thanks</font>
Hey guys, I was wondering if a 1996+ Camaro SS/Firehawk Hurst Shift **** would fit my 86 IROC T-5?? Like do they share the same threads and shaft size and everything?? Thanks</font>
I have heard from various sources, and even tried to fit a t56 shifter to a t5 myself, that it would not work. The t56 base is much longer, and oblong than the t5 base..
therefore they will not bolt up, however if your referring to the **** itself, i dunno.. i dont see a reason why the **** itself wouldnt work.
-steve
92 rs/ss frankencamaro
406/t5 / i wish i had a t56
www.groundzerocustoms.org
Supreme Member
Joined: Mar 2000
Posts: 1,160
Likes: 1
From: Lexington, SC
Car: 1992 Z/28, 2000 SS, 1968 RS/SS
Engine: 355 Built a bit / LS1
Transmission: T-5 / A4
Axle/Gears: 4.10 / 2/73's
I just re-read what you guys wrote to begin with.. IM A MORON. just wanted to clarify that as though my last post didnt.
dough!
Maybe next time ill read more carefully before replying
-steve
92 rs/ss frankencamaro
406/t5 / i wish i had a t56
www.groundzerocustoms.org[/B][/QUOTE]
dough!
Maybe next time ill read more carefully before replying
-steve
92 rs/ss frankencamaro
406/t5 / i wish i had a t56
www.groundzerocustoms.org[/B][/QUOTE]
Member
Joined: Sep 1999
Posts: 361
Likes: 0
From: Allentown, PA
Yes, the shifter ball should fit, both use 16mm x 1.5 thread. Least according to B&Ms website.
------------------
1989 Camaro RS LO3 WCT5 0-60' 2.34 1/4 15.8@87mph
http://350.StreetRacing.org
The posi unit breaker.
[This message has been edited by Get Blown ? (edited February 21, 2001).]
------------------
1989 Camaro RS LO3 WCT5 0-60' 2.34 1/4 15.8@87mph
http://350.StreetRacing.org
The posi unit breaker.
[This message has been edited by Get Blown ? (edited February 21, 2001).]
Thread
Thread Starter
Forum
Replies
Last Post
1992 Trans Am
History / Originality
27
May 10, 2023 07:19 PM
dhonda200
Transmissions and Drivetrain
6
Aug 11, 2015 11:50 PM
