http://www.ls2.com/forums/showthread...hreadid=357781


check this out , its on ls2.com , so i dont know if you have to register or not , i allready am , but theirs a guys selling them again , I allready had a set from a guy off ebay and tgo and now someone on ls2 is making them so . but here they are if you looking for them .

 

heres the ebay ad for the ones on ebay they look pretty nice. but only for irocs unless you want an iroc engraved door sill in a pontiac. pretty cheap too.

http://cgi.ebay.com/ebaymotors/2-IRO...spagenameZWDVW

 

If you guys are interested in a group purchase, let me know. I've been in contact with a manufacturer about having some made, and he seemed fairly receptive to the idea. If there's enough interest, I'll talk with him again. From what I understood from my prior discussions, they'd be somewhere in the range of $50-ish per pair, but these are a full piece that replaces the plastic piece, not a stick on cover.

 

That's not a bad idea Jim. I'd be willing to get in on a group purchase especially since it would be the entire piece, not just a stick on.

 

I would like to get some.

 

i'd be interested in a set too.

thanks

 

i think a group purchase is in order. im definatly in for a set to replace the whole sill
matt

 

If it replaces the whole sill, I would be interested. The last time this came up, it was a stupid stick on peice.

 

I'd seriously consider it too.. I like the look...

 

I would like them if I can see before hand what they will look like..

 

I would be interested as well. what would they say though? I hope maybe chevrolet with a red bow tie or something like that.

 

Count me in on this one too, I would love to have a set.
Han

 

if they come mirror polished and replace the whole sil, im for 50bones

 

Z28, Trans Am, and Iroc-Z?

Z28 here... That'd be very cool.

EDITL Quoted the wrong person...

 

I would be in, but it would either have to come blank, or in all the versions of our cars.

 

Count me in for some Iroc-Z ones

 

Same here!

 

I could dig on a set also, the IROC ones

 

im very interested as well, as long as it says "pontiac" or "firebird"

 

What would be cool if they had some lighted ones, where the IROC-Z logo lights up everytime you open the door.


EDIT: I take that back. It would be nicer if the sills were just plain satin finish, with no writing.

 

I'm interested.

 

It would be sweet if sombody would make them out of Billet kinda like what the sport truck scene has. Actually does anybody Know if the door sills from any truck model year will fit a third gen camaro, maybe with a little Massaging?

 

Id also be interested, I hate the plastic door sills that come on our cars. Id like a set that said Camaro in the 3rd gen font or IROC-Z. Either one would be awesome.Hook it up

 

awsome, id be down for 2 or 3 sets
get er done!

 

I'd go for an IROC set.

JamesC

 

If it has a mirror polished finish to it and comes either blank or with a logo relative to my camaro, you can count me in.

 

Im very interested in a GP if an international order would be acceptable.


Ken

 

of course im down. But id much rather get better aftermarket emblems for our cars.

 

these are mine, i didnt realize those were stick on crap . sorry guys .

 

I also would be interested in a set for a T/A, provided they are the one piece unit to replace the plastic door sill....

 

How about "Camaro" instead of all the IROC, Z28, RS, SC, Berlinetta crap.

 

I'd be down with a set for the IROC

 

I'd like a set too, that says pontiac or firebird or something.

 

Could someone easily make a pair of these themselves? From what I can see there are no bends or anything.

 

I'd be down for a set

 

Yes, that company in the link sounds like the same manufacturer as the last time this was mentioned as a GP. Aluminum Sill Plates

I am interested in an aluminum sill plate that held in like the stock ones. 18inchboyd's custom ones are great. If Jim can arrange a group purchase, I am tentantively in.

Look closely, there are bends in the sill plates. You'd need a sheet brake. Plus the inner edge is notched for the seatbelt.

 

count me in for sure....blank, or camaro/firebird is what would be best IMO

 

It would also be great to have aluminum door sills with smaller cutouts to accommodate 4th gen seat belts. A much cleaner look in my opinion. Just thought I'd throw it out there...

 

Ok, there seems to be enough interest. Let me contact the guy and see what I can do.

From talking with him in the past, these are a full piece that goes over the entire existing door sill. I'll find out more though.

I don't know about satin, and I doubt I can get them with logos, but I'll check on that too.

 

Plain are the best bet for a wider group appeal. If you want a logo, buy a decal or sticker and apply it.

 

I want a set.Let me know.

 

I am also interested in a set just let me know. I want mine plain and mirror finish.

 

...? clarification please?

 

I would be down for a set or 2 in plain. I would also rather have them without the cut out part for the seatbelt retractor. I plan on doing away with factory seatbelts.

 

Thought this was interesting, have any of you ever used these? I thought I would bring it up here to match the sills I saw them on e-bay and thought it was a bit weird to have aluminum floor mats.

 

I want a set.Let me know.

 

I talked to them this week, and they promised to send me some pictures, but I'm still waiting for them.

It also sounds like they're going to send me a couple of them so that I can evaluate them, and take my own pictures of them installed in the car. Apparently they can offer these in chrome, as well as diamond plate and regular aluminum.

They can also do aluminum and diamond plate floor mats if anybody wants those.

I'm going to call them back early next week and see what the hold up is for getting the pictures to me. I'm also going to try to get the wheels turning for those samples so that I can see what they are.

From what I understand, these don't replace the stock sills, but go over them. Whether or not they stick on or bolt on, I don't know yet, but from the original picture I saw of their diamond plate ones, they looked pretty good.

Perhaps we should start a thread in the group purchase forum, that way we'll have a good spot to keep updates.

 

Do you have a price on the floor mats?

 

I can get one. I never asked him because I didn't expect there to be any interest in them.

 

Well I thought it was kinda weird to have stiff floor mats and was wondering if anyone had used them before. The ones on e-bay are like $90 shipped but I don't know if I would like them without some reviews.
Thanks