Parting out '91 Camaro RS
Thread Starter
Supreme Member
iTrader: (1)
Joined: Dec 2000
Posts: 1,197
Likes: 0
From: Crete, IL 60417
Car: 2004 Chevy Avalanche
Engine: Some that run, some that don't
Transmission: 700R4's, a T-5, and a Turbo 350
Parting out '91 Camaro RS
Since the classifieds are down I figure I would post this here. I just got a '91 RS that I am going to part out. It is red with a red interior. The car is in very nice shape. Everything is available except for the drivetrain. I will not ship body panels. The ground effects are in very good shape and I want to sell them as a set. If you are interested in anything let me know.
Junior Member
Joined: Dec 2001
Posts: 21
Likes: 0
From: Greenville, NC
Trending Topics
Supreme Member
Joined: Mar 2001
Posts: 1,065
Likes: 0
From: Tucson, Az, USA
Car: 1992 RS
Engine: 3.1L V6
Transmission: T5
If the front struts are still good, and the steering column( don't need the steering wheel). I would like those! Also if the 3rd brake light works. Maybe the rear bumper cover, if it has no rips. Paint can be bad. It doesn't matter.
Joined: May 2001
Posts: 1,427
Likes: 496
From: Pflugerville, Texas
Car: 92 Heritage Camaro Z28
Engine: 350 TPI
Transmission: auto
Axle/Gears: 3.23 Limited Slip
I need a few interior trim parts.
1. The passenger side seat belt holder that goes on the top part of the seat. I do not know whatit is called.
2. one of the rear trunk plastic covers that go over the rear struts on the hatchback.
3. Drivers side seat belt plastic holder that goes on the floorboard near the center console.
Email me at mlduarte@earthlink.net
Thanks!!!
Manny
1. The passenger side seat belt holder that goes on the top part of the seat. I do not know whatit is called.
2. one of the rear trunk plastic covers that go over the rear struts on the hatchback.
3. Drivers side seat belt plastic holder that goes on the floorboard near the center console.
Email me at mlduarte@earthlink.net
Thanks!!!
Manny
Senior Member
Joined: Jun 2001
Posts: 609
Likes: 2
From: Pearland, Texas
I'd be interested in the gauge cluster if it is a v8 tach. E-mail me chaserath@hotmail.com .
Junior Member
Joined: Dec 2001
Posts: 1
Likes: 0
From: Nebraska
front seats and other stuff
i could use the front seat the back seat and the rims if it has t-tops i could use them or jsut the handle
email me Amsler15@Homtail.com or bad_boy_24_@hotmail.com
email me Amsler15@Homtail.com or bad_boy_24_@hotmail.com
Senior Member
Joined: May 2001
Posts: 745
Likes: 0
From: springfield,IL
Car: T/A / Grand Am
Engine: 383 SBC
Transmission: glide
Axle/Gears: 9" ford 5.67
Originally posted by FatOne
Was it a TPI model? If so do you still have the ECM,PROM, and wiring harness? Let me know something I've been looking for a while.
Was it a TPI model? If so do you still have the ECM,PROM, and wiring harness? Let me know something I've been looking for a while.
Supreme Member
Joined: Mar 2001
Posts: 1,754
Likes: 0
From: Pekin, IL
Car: 91 Formula, 79 Trans Am, 72 LeMans
Engine: 305 TPI, 6.6, 350 Pontiac
Transmission: T5, 3 speed, TH350
I need the front two seats if in perfect shape or the whole set if they don't match my red 89 interior. I would also like the console also. How far are you away from me? I am in central Illinois
Supreme Member
Joined: Mar 2001
Posts: 1,754
Likes: 0
From: Pekin, IL
Car: 91 Formula, 79 Trans Am, 72 LeMans
Engine: 305 TPI, 6.6, 350 Pontiac
Transmission: T5, 3 speed, TH350
I need the ground effects too so email me and shoot me a price, and I need the speaker covers in the back and front seat belts as well. Thanks
TGO Supporter
iTrader: (2)
Joined: Jul 1999
Posts: 13,579
Likes: 9
From: Readsboro, VT
Car: 85 IROC-Z / 88 GTA
Engine: 403 LSx (Pending) / 355 Tuned Port
Transmission: T56 Magnum (Pending) / T5
Axle/Gears: 3.42 / ?
If it's a 5 speed, I need the lower rubber shifter boot that bolts to the floor. Thanks.
Thread
Thread Starter
Forum
Replies
Last Post
