Anybody order the pocket programmer ?
Thread Starter
Senior Member
Joined: May 2000
Posts: 980
Likes: 1
Anybody order the pocket programmer ?
If so how long approximately did it take to get your to door ? 
(i'm anxious to get mine... hehe)
------------------
92 Z28 L98 350
---------------
Ported and polished heads, ported stock TPI base, ported plenum, Comp Cams XR270HR-10 cam (lift .495/.502 duration 218/224 lobe separation 110), Edelbrock TES headers, LT4 valve springs, Crane AFPR, Flowmaster catback with LT1 style tips, MSD coil & wires...
"Take that auto, drop it in first, hold the brakes, stomp the gas and grin from ear to ear! :-)
[This message has been edited by Blade (edited October 07, 2000).]
(i'm anxious to get mine... hehe)------------------
92 Z28 L98 350
---------------
Ported and polished heads, ported stock TPI base, ported plenum, Comp Cams XR270HR-10 cam (lift .495/.502 duration 218/224 lobe separation 110), Edelbrock TES headers, LT4 valve springs, Crane AFPR, Flowmaster catback with LT1 style tips, MSD coil & wires...
"Take that auto, drop it in first, hold the brakes, stomp the gas and grin from ear to ear! :-)
[This message has been edited by Blade (edited October 07, 2000).]
Junior Member
Joined: Oct 2000
Posts: 38
Likes: 0
From: Dalton, GA, USA
Blade,
It took about 4-5 days. Did you order a eraser to? If you did where did you get it? I have a very crude device made out of plastic box with a 15 watt 120 volt single bulb flor. fixture using g15t8 bulb
(germacital 15 watt T8 18" long bulb) Its large enough to erase 400 eproms at once. It cost me about $35.00 I made it out of parts I had around the shop. The bulb is most of the cost.
It took about 4-5 days. Did you order a eraser to? If you did where did you get it? I have a very crude device made out of plastic box with a 15 watt 120 volt single bulb flor. fixture using g15t8 bulb
(germacital 15 watt T8 18" long bulb) Its large enough to erase 400 eproms at once. It cost me about $35.00 I made it out of parts I had around the shop. The bulb is most of the cost.
Thread Starter
Senior Member
Joined: May 2000
Posts: 980
Likes: 1
I plan to get the eraser in about 1 week or so. I got the programmer today and I burnt two chips already. So far I get a 51 code from my ECM and the car runs good except the speedo doesnt work and the SES light comes on all the time.... 
[This message has been edited by Blade (edited October 12, 2000).]
[This message has been edited by Blade (edited October 12, 2000).]
Thread Starter
Senior Member
Joined: May 2000
Posts: 980
Likes: 1
Yeah I got the programmer... I burned two chips I found on the internet and they SUCKED. I compared the timing tables and the JET stage 2 chip I had in the car was far superior. LOL The bad thing is... I dont have an eraser yet so I Cant erase them and reburn em. One day in the sun didnt do the trick.. so I gotta go buy one tomorrow lol
I dont even know what to change yet to make my car perform better, but I guess I'll be messing around with the timing and KPA values until it feels better. lol
------------------
92 Z28 L98 350
---------------
Ported and polished heads, ported stock TPI base, ported plenum, Comp Cams XR270HR-10 cam (lift .495/.502 duration 218/224 lobe separation 110), Edelbrock TES headers, LT4 valve springs, Crane AFPR, Flowmaster catback with LT1 style tips, MSD coil & wires...
"Take that auto, drop it in first, hold the brakes, stomp the gas and grin from ear to ear! :-)
lolI dont even know what to change yet to make my car perform better, but I guess I'll be messing around with the timing and KPA values until it feels better. lol
------------------
92 Z28 L98 350
---------------
Ported and polished heads, ported stock TPI base, ported plenum, Comp Cams XR270HR-10 cam (lift .495/.502 duration 218/224 lobe separation 110), Edelbrock TES headers, LT4 valve springs, Crane AFPR, Flowmaster catback with LT1 style tips, MSD coil & wires...
"Take that auto, drop it in first, hold the brakes, stomp the gas and grin from ear to ear! :-)
Thread
Thread Starter
Forum
Replies
Last Post