Ignition issue
#1
Junior Member
Thread Starter
iTrader: (1)
Join Date: Jan 2008
Location: Lancaster, Pa
Posts: 45
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1987 Iroc-Z
Engine: SD360 350 Vortec
Transmission: 700R4
Ignition issue
Hello all-
I have just performed an engine swap and I am having an issue getting the starter to work. I am getting 12 volts to the starter, when I turn the key on the radio and lights all turn on, but my fuse for my gauges blows out and nothing happens to engage my starter/solenoid. I have looked at all my grounds (I think I covered them all, but could be missing a ground somewhere), but have not been able to turn up anything? I am not sure what is causing my fuse blow out, is that what is also inhibiting my starter from working too? Any suggestions or help would be greatly appreciated.....
Thanks,
Tony
I have just performed an engine swap and I am having an issue getting the starter to work. I am getting 12 volts to the starter, when I turn the key on the radio and lights all turn on, but my fuse for my gauges blows out and nothing happens to engage my starter/solenoid. I have looked at all my grounds (I think I covered them all, but could be missing a ground somewhere), but have not been able to turn up anything? I am not sure what is causing my fuse blow out, is that what is also inhibiting my starter from working too? Any suggestions or help would be greatly appreciated.....
Thanks,
Tony
#2
Junior Member
iTrader: (1)
Join Date: Jun 2008
Location: Kentucky/Tennessee
Posts: 95
Likes: 0
Received 0 Likes
on
0 Posts
Car: 91 Camaro RS/2005 Dodge 1500 4X4
Engine: 305/ 5.7 HEMI
Transmission: 700r4
Re: Ignition issue
No i doubt it, But I do beleive there is a short (ie: Pinched wire, bad connection) That is causing that fuse to blow. And it probably has a role in the ignition switch, wich is prolly why you have no start. These little things will drive a man crazy. I am pretty confident in this opinion, Find that short and you will have fixed your problem..Goodluck
#3
Supreme Member
iTrader: (7)
Join Date: May 2004
Location: Lexington, SC
Posts: 5,291
Likes: 0
Received 58 Likes
on
52 Posts
Car: 1987 SC/1985 TA
Engine: 350/vortec/fitech
Transmission: T56
Axle/Gears: 3.27 9-bolt
Re: Ignition issue
The guage fuses blow when the key is on AND the starter won't engage or when you hit the starter the guage fuse blows?
If it's number one, sounds like two problems. Short in your guage wiring somewhere and check your starter-make sure the little wire's on the right terminal.
If fuses are blowing when you try to turn the starter trace down the starter solenoid wire it's shorting somewhere.
If it's number one, sounds like two problems. Short in your guage wiring somewhere and check your starter-make sure the little wire's on the right terminal.
If fuses are blowing when you try to turn the starter trace down the starter solenoid wire it's shorting somewhere.
#4
Junior Member
Thread Starter
iTrader: (1)
Join Date: Jan 2008
Location: Lancaster, Pa
Posts: 45
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1987 Iroc-Z
Engine: SD360 350 Vortec
Transmission: 700R4
Re: Ignition issue
okay, I did a little more investigating and found that the fuse is infact popping when the key is the on position and not in the starting position. So, will this inhibit me from starting the car was well? or do I have two problems?
#5
Supreme Member
iTrader: (7)
Join Date: May 2004
Location: Lexington, SC
Posts: 5,291
Likes: 0
Received 58 Likes
on
52 Posts
Car: 1987 SC/1985 TA
Engine: 350/vortec/fitech
Transmission: T56
Axle/Gears: 3.27 9-bolt
Re: Ignition issue
Find out which fuse, get a wiring diagram and trace down everything connected to it. Could be as simple as a bad cig lighter, lamp, etc.
Thread
Thread Starter
Forum
Replies
Last Post