*HEAVY ITEMS ARE PICKUP ONLY*

Pair of 083 heads rebuilt not too long ago - 100

Stock tpi runners (a couple tiny dents) - 25

Ported tpi plenum (egr walls gone, tb opening enlarged, siamesed ports) - 50

Ported stock tpi lower base (opened up throughout the entire ports) - 50

K&N speed density tpi tb mounted filter (brand new) - 20

Dynomax 2.5" inlet dual 2.5" outlet muffler (5k miles no rust) - 20

4th gen stainless steel muffler 3" inlet dual 2.5" outlets (50 miles) - 30

91-92 speed density tpi wiring harness for camaro (full harness no cuts) - 50

Comp cams XE-268H camshaft (NIB) - 75

Comp cams 7949-16 set of 16 1 piece chromoly 5/16 7.300" pushrods(NIB) - 80

Manley 1.250" diameter valve springs with matching Manley +0.050" clearance retainers(good for more lift with no head work)(2k miles) - 125

Vortech 30Ib fuel injectors(set of 8, great condition, new o rings, i just needed larger ones, black with a red ring on top) - 125

TBI ECM with stock memcal for an 89 firebird with VATS - 25

TPI factory fuel rails(no dents in tubes) - 25

TPI firebird fuel lines crossover from rubber-rails(no rust painted to keep it away) - 15

TPI firebird factory air intake canister modded for more airflow - 20

TPI firebird factory air intake rubber piece off of the canister to MAF sensor - 15

TPI firebird factory air intake rubber piece from MAF to TB (modded for nitrous nozzles) - 15

 

Could you post or send pics of the last 3 items to gaccett@yahoo.com

 

I sent you a PM.

Thanks!

 

do you have a TPI ECM to go with that harness?

 

pictures as requested by all. Gaccett just a note remember the elbow that goes on the tb has 2 holes near the throttle body one underneath and one driverside on top but they can be plugged if you need. I however at this time dont have a picture of the rubber piece from MAF to canister at this time but i garauntee mint condition and can get pictures at work if youd like tomorrow. Luke no i do not have the computer im keeping it sorry. The picture of the ported base was before it was ported even more the second time if you wish i can go down to work tomorrow and take more pictures of it from all sides. It is now ported to fit a 1205 intake manifold gasket on that side and ported as large as i felt comfortable with on the runner side. Also the plenum picture shows the porting in progress not the egr walls are smooth and dont intrude into the throttle bore area anymore and the sides are even ported down a little smoother.

 

----------

 

pm'd you i think i can help u out lol

 

I actually needed the intake duct to be straight not angled. Sorry.

 

pics of harness??? im very interested

 

Still have the fuel rail assembly? camaro87-alex may need it. PM him for the sale.

 

what size valves are in those heads? and what cc is the chambers?

 

harness sale is SOLD

ported plenum and base is SOLD

fuel rail is still available i will pm him. thankyou

the 083's have 64cc chambers with 1.94/1.50 valves.

 

Where in CT are you?

 

im 10 minutes from hartford.

 

items updated on whats sold.

also for sale a black Marshal nitrous pressure gauge(mechanical 1/8npt port)

 

bump for a boring snowy day

 

Wondering if the K&N filter will fit a holley 58 mm TB as the one i had on the stock TB is too small and am forced to now use the stock intake tubing....

 

pm sent