Since I need to pay rent and alot of bills I am selling off some of the stuff I had sitting around I have been planning on putting on my car but I need to come up with some cash so I guess it has to go.

2.5" Goodmark Cowl induction hood $350 pick up only unless you want to pay for shipping but pick up is way easier. (this is new still in the edp coating)



93-02 Camaro shocks and struts (these are new still in the boxes) $160

set of 4 Camaro SS rims (17") no tires these are stripped to polish $350 ( I can polish these for an additional $40 per rim) I was going to try and inset the iroc center caps into the center caps.


93-02 Camaro convertible tonneau cover $200

2 center console top plastic for 82-92 Camaro console $20 and shipping for either

96 Camaro seats. I have the whole set they are gray and black $250

lots of Camaro interior trim pieces just ask. ?

camaro convertible header trim (I have these on here already with pics but I am dropping price to $100 each).

Complete 82-92 Camaro front end rebuild kit from Moog parts (inner and outer tie rods and new billet adjusters center link and pitman arm. I haven't looked at this stuff in a while so I will need to check and make sure all is still there and didn't get misplaced) $250







I have 2 camaro eq head units also $45 each

My 95 Camaro convertible is also up for sale if I can get $2800 out of it. (I want something bigger)

Custom built 2 cycle gas RC truck 29cc gas motor and 4 wheel steering. $1250 I have over $1900 in it. pics on the flickr link below.


all prices are plus shipping unless we negotiate on a shipped price. I am in NW Ohio I can get pics just too busy right now. after there is interest I can either send or post pics. I am not going to rip anyone off I just need cash

 

i am interested in

"...Complete 82-92 Camaro front end rebuild kit from Moog parts (inner and outer tie rods and new billet adjusters center link and pitman arm. I haven't looked at this stuff in a while so I will need to check and make sure all is still there and didn't get misplaced) $250..."

looking for inner/outer tie rods by Moog

thx

 

what years are the bose radios?

 

one is correct for an 89 the other looks like more than likely 87, so 84-89

 

also on the tie rods I would rather keep it all together unless anyone wants to buy the pieces that are left over after the tie rods.

 

Complete 82-92 Camaro front end rebuild kit from Moog parts (inner and outer tie rods and new billet adjusters center link and pitman arm. I haven't looked at this stuff in a while so I will need to check and make sure all is still there and didn't get misplaced) $250


is this all that comes in the kit? any ball joints? just curious I'm looking for a complete kit ball joints and all.

 

:P

 

Can you post pictures of the rims?

 

Can you get a pic up of the bose radios? i may be interested in one of them, providing it works.

 

I will have them up after I get them resized. I got both of them to do Ipod inputs on them but I need cash and don't have time. both of them came from a board sponser. They were both tested before sent.

 

I live in Columbus Im not sure where Tiffin is but since your in Ohio maybe you give me a good ol Buckeye package deal if I come and pick up the hood, the seats(If they fit a 1990 convertible RS) and dash pad from where ever your at. You can contact me private if you dont want everyone to know the buckeye deal. lol

 

I'd be willing to do $800 for the dash pad seats and hood. I have way more in them but you'll use them faster than me anyway. the dash is somewhat different but it fits just not correct for the year. seats and hood are a direct swap. also you are around an hour and a half away not too bad of a drive.

Here is everything that is included with the front end kit.

Energy Suspension Control Arm bushings
Prothane tie rod end boots
idler arm
ball joints
center link
billet tie rod adjuster
inner and outer tie rods
all the necessary hardware

here is a link to my flickr account with pics of some of the stuff including the front end kit and rims and radio's and convertible trim pieces. http://www.flickr.com/photos/1839044...7622412517185/

 

I didnt even think about the dash pad being different, its just the top part right? I forgot i have the 90-92 gauges but like you said it should still work. I know where another one is correct for my year,but my main interest is the hood and seats could i see a pic of them if possible.THANKS

 

yeah it is just the top pad. I have a complete non a/c dash setup but not positive I want to sell it yet. I will try and get pics later on tonight.

 

that one radio isn't a bose, it would say delco.bose if it did...how about the other one?

 

guess not but they both have an extra plug coming out of the back that is why I just assumed BOSE I guess. guess that makes me the first 3 letter of assume.

 

Do you have any pictures of the seats?

 

check the flickr link above I added pics of the seats and hood and dash. The seats are kind of dirty I can clean them up for whoever buys them. alot of this stuff has just been sitting so it is dusty.

 

Do you have all 4 center caps with those wheels?

 

yeah I have all 4 caps and also a set of spacers I will sell.

 

What size engine did the trannies come off of? any idea how bad shipping would be to 29212 columbia sc?

 

the 700r4 was with a stock 305 carb motor felt like it had a shift kit in it, the th400 was behind a 454 but needs rebuilt. shipping I would guess would be around $125 or so for either one. I will have to check for sure.

 

Can i get a pic of the th400 torque arm and crossmember, and possiby a part #

 

I am trying to get the dash boxed up so I really don't have time right now for a pic. but the part # is 304 the torque arm and Xmember are both brand new never been mounted. They are black. I will try and get a pic later on.

 

use the flickr link above I added pics of the torque arm. I got the torque arm off of ebay but it is brand new though. and I just bought the X member around 3-4 months ago from Spohn.

 

Can you send me pics of the nicer console lid and the seat set. thanks

 

Pics of the quick fuel carb?

 

I added a pic of the carb to the flickr page above. The fuel rail is extra if you want that too. I don't have the butterfly flaps on it but I have them all and all the hardare it will be sent complete (minus boosters). When I talked to the guys at QFT about it they said $200 and they would recolor and a gasket kit and boosters installed.

 

I will probably start listing some of this stuff on Ebay later unless I get some offers on this stuff. I have alot of interior stuff too just ask.

 

PM sent

 

ttt

 

added my RC truck too pics in the Flickr link above.

 

ttt

 

im in parma ohio would you sell just the th400 mount not the arm

 

no I don't want to seperate I may end up just keeping that stuff anyway. Sorry.