rebal_4_ever2003@yahoo.com Thanks

 

i dont know if its needed for the ls1 swap but are you selling the throttle cable?

 

rebal_4_ever2003@yahoo.com Thanks

 

Throttle cable got sent with the HSR. I will get on it now banksGTA.

 

You take 200$ shipped?

 

$250?

 

Willing to. Sell the serpentine setup? I need both brackets,tensionern ac delete if you have it and all bolts and braces for the setup. Lmk I know you said you may seperate if you don't sell motor. Thanks

 

I have all bolts. I have all brackets. I scrapped the tensioner. I left the A/C compressor on for the belt routing. I sold the crank pulley. Smog pump was scrapped.

 

Are the heads still good the l98'heads that were on your engine?

 

Will you sell the rocker arms? if so, how much?

 

can you give me shipping to 02790? thanks

 

I am interested in the harness and the ecu. Can you separate the Moates chip adapter with AUJP memcal?

 

ttt

 

Interested in the oil pan, how big is it? Do you have the part number for it? Any dings or dents? I need one for a 1 pc rms small block into an 88 Camaro. Thanks

 

was wondering if u have the ESC if so how much shipped to 18428?

 

tpi harness speed density $130 shipped
Ecu 730 with burnable chip and Moates chip adapter with AUJP memcal $150 shipped

I am interested in this^^^
Thanks

 

Items added, make offer must go

 

how much without the ecu

 

PM sent

 

bump

 

pm about heads and block

 

I didn't look through all the posts, but private msg me about the starter. I'm building a 12.0:1+ compression, my stock starter might do it, but not likely, 10.75 or 11:1 is usually the limits for "stock"

 

if I read all of the posts correctly, the 730 ECM is still available?
I would be interested in the ECM and Memcal if they are available.
Could you shoot me some info, and pricing to: vrodpete@msn.com?
Thanks,
PK

 

PMs replied

 

I appreciate the "Priavate message" I receibeved, its clearly not there. I didn't buy your parts, because your far away, I boughta whole new motor & its build to handlge 800+ hp, rather than spending gas money to drive 700 miles there, and 700 back. So, clearly now, hope you sold the rest of your s h i t

 

No I dont have a site with the car on it. It is not really presentable. It is a work in progress, LS1 right now, then I want to clean the engine bay up and freshen up the interior before I take pictures of it. Cant wait to see the progress on your engine, sounds like it will be fast. I will check on this pan tomorrow, its hot (110) and the heat pushed me out of the garage and into the house.

Quote:
Originally Posted by cronsformula350
Nice, I'm glad you sold it, I have to use my current one anyway, I am also low on funds, but now have to build a forged motor. Do you have a site with more info on your car? I always like seeing others car guys work and what not, Keith.

Quote:
Originally Posted by camarotucker
Quote:
Originally Posted by cronsformula350
Quote:
Originally Posted by camarotucker
Quote:
Originally Posted by cronsformula350
Quote:
Originally Posted by camarotucker
HSR only? No throttle body?

well what would be ok?

$650 shipped HSR and BBK throttle body

No offense, but I just spent $500 on the strongest GM block, forged rods, bearings, flexplate, solid roller lifters, and some serious other stuff to buy later, but I paid $$500, I'm getting my crank for $400 and $100 for the sfi 19.1 damper, so 500 to finish the bottom end! Thats less for a lot more, I have that intake, but maybe sell it to someone else that wants to spend that much. The economy is ****ed up now, and a lot of guys are selling a lot of **** at a loss, because they need the money. I need money, but I'm building a 800hp bottom end, 1000 on spray lol, lightweight, HIGH compression. 10.96:1 with my current heads. So try to find someone willing to pay that much, I mean I know I spent $680 on mine, but had extra parts

sold

 

I replied to all Private Messages, and to many of yours. My apologizes for missing your question here on the thread, as soon as you asked about the starter I recived a payment for it and a note that came with the payment stated that it was need for a high compression build. I never put it together that it was two diffrent people inquiring about it. Glad to hear that you are closing in on finishing your build and look forward to seeing some pictures posted of it here on the boards.

 

bump

 

Still need an oil pan and a new water pump lol, I even bought a good TPI 305 to drive my car for the rest of the year lol, while I build the other one

 

PM sent

 

heads-assembled sold

 

Did you ever sell the rest of the serpentine setup? I am interested, all of it. You don't have to ship I can get to Wichita. Thanks, John

 

How much for the door dings molding? What color is the underlaying color of the plastic?

 

The serpentine was scrapped. Door ding moldings you can have for shipping costs, they are at the shop with the car, I can look tomorrow at what the plastic color is. They are off of my 91 so they are the wider style. If you send me your e-mail address chevy86 I will send you pictures tommorow night.

 

Sold!!!!!! Silent_for_life@yahoo.com . I need those moldings. Thanks man. I appreciate it. Chevy86 IROC-Z

 

pm sent

 

camarotucker, they look good (ding moldings)! Find out the shipping costs and Ill paypal you a payment. Im in no rush so if you can send it via USPS, that would be perfect. Thanks camarotucker. PM me your Paypal email account so that I can pay for the shipping.