[WA] pics.WTS.. NOS sportsmen fogger kit $180Shipped!
#1
pics.WTS.. NOS sportsmen fogger kit $180Shipped!
1 .also have a NOS SportsMen fogger Kit (no bottel or Hard lines) easy and cheap to get parts. $180 you get!
8 fogger nzls
16 jets (180 hp Hit at 7psi fuel 900psi nos) have 2 other sets 16 jets ea set
this set of snds have never been used..still new (they have been installed only!!
2 nos snds
2 fuel snds
4 dist blocks 2 fuel 2 nos
(this was on my accel super ram) so you get the hard lines for it
and alot of small parts and hand book that comes with this kit.
easy to set up and use. $180 shipped
Price it out guys..it's a deal!
3.Oil cooler this is a big one Guys holds almost 2qts of oil size 12AN fittings
made BY C&R, cost is over $400 new
give it away for $60 shipped
this is first 48 states. first ill take it gets it
Pay pal is Good add the 4% paypal fee
8 fogger nzls
16 jets (180 hp Hit at 7psi fuel 900psi nos) have 2 other sets 16 jets ea set
this set of snds have never been used..still new (they have been installed only!!
2 nos snds
2 fuel snds
4 dist blocks 2 fuel 2 nos
(this was on my accel super ram) so you get the hard lines for it
and alot of small parts and hand book that comes with this kit.
easy to set up and use. $180 shipped
Price it out guys..it's a deal!
3.Oil cooler this is a big one Guys holds almost 2qts of oil size 12AN fittings
made BY C&R, cost is over $400 new
give it away for $60 shipped
this is first 48 states. first ill take it gets it
Pay pal is Good add the 4% paypal fee
Last edited by articwhiteZ; 09-21-2012 at 04:31 PM.
#3
Re: WTS Aluminum Drive Shaft $100 shipped NOS foger kit $180
handling marks and some dust. it's used but from a stock camaro. i had it for a back up but never used it. got it from hawks.($150)+ shipping, and just have it sitting.no dings all GM stickers are still on it. drop in. has sold to me from Hawks.
wil try to get a pic up in a few..
wil try to get a pic up in a few..
Last edited by articwhiteZ; 09-07-2012 at 06:26 PM.
#5
Senior Member
iTrader: (7)
Join Date: May 2005
Location: Toronto, Ohio
Posts: 722
Likes: 0
Received 1 Like
on
1 Post
Car: 1991 Trans Am GTA
Engine: 355
Transmission: 4L60
Axle/Gears: 4th gen 10 bolt 3.42 posi
Re: WTS Aluminum Drive Shaft $100 shipped NOS foger kit $180
Definitely interested in the Nitrous setup. What would I need to put it on my Superram? I already have a bottle.
#6
Re: WTS Aluminum Drive Shaft $100 shipped NOS foger kit $180
you would drill and tap your top box, like i did. easy easy
you can see in this shot. the nozls fit over the runners,and spray down into them,
you do get the hard lines for this set up. im sure you can make more. they are easy. to make.
the 2 shots also show the way to set up a super ram with a fogger. (even lay out on the 2 sides) you can set them up anyway you like.
just buy 2 silnds and you spent more the the $180...
sorry for the dust..been sitting a few years in my shop when pics was taken
and if you want to remove the kit you plug holes,with 1/4 pipe plugs..they only go in 1 way. and not all the way in..how easy and simple is that, price it out it's a steel! the sale price is less the 6 fogger nozls.. !
you can see in this shot. the nozls fit over the runners,and spray down into them,
you do get the hard lines for this set up. im sure you can make more. they are easy. to make.
the 2 shots also show the way to set up a super ram with a fogger. (even lay out on the 2 sides) you can set them up anyway you like.
just buy 2 silnds and you spent more the the $180...
sorry for the dust..been sitting a few years in my shop when pics was taken
and if you want to remove the kit you plug holes,with 1/4 pipe plugs..they only go in 1 way. and not all the way in..how easy and simple is that, price it out it's a steel! the sale price is less the 6 fogger nozls.. !
Last edited by articwhiteZ; 09-08-2012 at 08:59 PM.
Trending Topics
#8
Re: WTS Aluminum Drive Shaft $100 shipped NOS foger kit $180
you might need to replace a hard line. i will send ss hard lines with the Kit.
the kits sell with just yellow zink plated lines.i replaced every thing with the nos ss lines. you can buff them out to a chrome like finnish.
all the brass fitting you get from any auto parts shop. anyplace(if you need them).when replacing a hard line you need them also.
look at the spacing i have them set at.
look how the kit comes (will ship it put together) for the most part.
will send the TP SAFETY (THINK TPS) but micro switch. see pics
you could install this in one afternoon. you will get everything that comes in a $700 kit but (bottel and hard lines) (hard lines are for a super ram)
and in that case.. yes you get the hard lines. and a few more parts.
you can get more hard lines for this Kit from Summit for under $40 in ss and for reg steel lines under $30 ya only need a few for back up will send what i have. left lines are sold 1 foot long. this kit you only need them 6" to 8" inch long. so you see you always have back up lines left over.
you can flair them your self or take them to a hose shop and have them do it.. cheap!
let me know...
the kits sell with just yellow zink plated lines.i replaced every thing with the nos ss lines. you can buff them out to a chrome like finnish.
all the brass fitting you get from any auto parts shop. anyplace(if you need them).when replacing a hard line you need them also.
look at the spacing i have them set at.
look how the kit comes (will ship it put together) for the most part.
will send the TP SAFETY (THINK TPS) but micro switch. see pics
you could install this in one afternoon. you will get everything that comes in a $700 kit but (bottel and hard lines) (hard lines are for a super ram)
and in that case.. yes you get the hard lines. and a few more parts.
you can get more hard lines for this Kit from Summit for under $40 in ss and for reg steel lines under $30 ya only need a few for back up will send what i have. left lines are sold 1 foot long. this kit you only need them 6" to 8" inch long. so you see you always have back up lines left over.
you can flair them your self or take them to a hose shop and have them do it.. cheap!
let me know...
#10
Senior Member
iTrader: (7)
Join Date: May 2005
Location: Toronto, Ohio
Posts: 722
Likes: 0
Received 1 Like
on
1 Post
Car: 1991 Trans Am GTA
Engine: 355
Transmission: 4L60
Axle/Gears: 4th gen 10 bolt 3.42 posi
Re: WTS Aluminum Drive Shaft $100 shipped NOS foger kit $180
I have a superram on my car now and I have an unused 4 & 6 cylinder fogger nitrous kit here that is complete, so I figure I should be able to throw it right on and not need anything. Does it only come with 180 HP jetting? Where does it tap in for fuel? Does it have purge?
#11
Re: WTS Aluminum Drive Shaft $100 shipped NOS foger kit $180
pics of drive line just dusty
clean stripe is just that, a clean Spot..think from zip tie.
stock steel one on the right from 92 Z28.
close up
clean stripe is just that, a clean Spot..think from zip tie.
stock steel one on the right from 92 Z28.
close up
Last edited by articwhiteZ; 09-08-2012 at 10:18 PM.
#12
Re: WTS Aluminum Drive Shaft $100 shipped NOS foger kit $180
I have a superram on my car now and I have an unused 4 & 6 cylinder fogger nitrous kit here that is complete, so I figure I should be able to throw it right on and not need anything. Does it only come with 180 HP jetting? Where does it tap in for fuel? Does it have purge?
i have alot of jets (a few bucks more)
Purge i do have one but (a few bucks more)
if you have a Kit now you Have the parts for a Purge (nos silnd) just need one.
of you can use one to one (2 for Purge) in front of your other 2
better look at the Nozls you have now, do they spray at a 90deg angl
shooting down into your Runners..they make some many diff ones.. just so ya know.
Jeff
Last edited by articwhiteZ; 09-08-2012 at 10:38 PM.
#13
Senior Member
iTrader: (7)
Join Date: May 2005
Location: Toronto, Ohio
Posts: 722
Likes: 0
Received 1 Like
on
1 Post
Car: 1991 Trans Am GTA
Engine: 355
Transmission: 4L60
Axle/Gears: 4th gen 10 bolt 3.42 posi
Re: WTS Aluminum Drive Shaft $100 shipped NOS foger kit $180
The kit I have now is a ZEX, so they are all in a box and I'd prefer not to mess with it.
Why do you have 2 fuel solenoids and 2 nitrous solenoids? Couldn't you get away with just 2 instead of 4? I'm trying to understand the setup, as it is hard for me to put it all together in my head through the pics, plus my knowledge is not 100% on nitrous yet.
How much for the kit with different jets and purge?
#14
Re: WTS Aluminum Drive Shaft $100 shipped NOS foger kit $180
I'd like to have some jets for between 100-125 HP, because I am still stock motor right now. You can keep the 180's.
The kit I have now is a ZEX, so they are all in a box and I'd prefer not to mess with it.
Why do you have 2 fuel solenoids and 2 nitrous solenoids? Couldn't you get away with just 2 instead of 4? I'm trying to understand the setup, as it is hard for me to put it all together in my head through the pics, plus my knowledge is not 100% on nitrous yet.
How much for the kit with different jets and purge?
The kit I have now is a ZEX, so they are all in a box and I'd prefer not to mess with it.
Why do you have 2 fuel solenoids and 2 nitrous solenoids? Couldn't you get away with just 2 instead of 4? I'm trying to understand the setup, as it is hard for me to put it all together in my head through the pics, plus my knowledge is not 100% on nitrous yet.
How much for the kit with different jets and purge?
you have a fuel and Gas supply on ea side of the motor.
you can get the jets you need from NOS/Summit. i dont think i have anything smaller then 180 Hit. would have to Look at my jet sets.
look at the pics i posted, ea bank is set up to spray. and to get a good flow. you need that many solenoids. ea one only flows so much.
and you need to flow enof that the jets you use slows the flow. and not the supply... you run nos by a set pressure. same with the fuel.
and you run that flow upto your Jets.. if you dont, flow enof... the jets will not do the work, and you will never get it set at the HP Hit you want,
hope that helps
Last edited by articwhiteZ; 09-08-2012 at 10:56 PM.
#15
Senior Member
iTrader: (7)
Join Date: May 2005
Location: Toronto, Ohio
Posts: 722
Likes: 0
Received 1 Like
on
1 Post
Car: 1991 Trans Am GTA
Engine: 355
Transmission: 4L60
Axle/Gears: 4th gen 10 bolt 3.42 posi
Re: pics.WTS Aluminum Drive Shaft $100 shipped NOS foger kit $180
Ok, I get it. I sorta figured it was a flow issue.
How much with the jets I want if you have them and purge?
How much with the jets I want if you have them and purge?
#16
Re: pics.WTS Aluminum Drive Shaft $100 shipped NOS foger kit $180
add $30 more for the Purge. it's also new used 4 or 6 times years ago.
was on this set up.
if i have them (Jets under 125hp set up) add another $35
they run $8.00 ea new, and you need 8 for fuel and 8 for NOS
if you want the jets in kit now and the lower HP Hit jets,
#17
Senior Member
iTrader: (7)
Join Date: May 2005
Location: Toronto, Ohio
Posts: 722
Likes: 0
Received 1 Like
on
1 Post
Car: 1991 Trans Am GTA
Engine: 355
Transmission: 4L60
Axle/Gears: 4th gen 10 bolt 3.42 posi
Re: pics.WTS Aluminum Drive Shaft $100 shipped NOS foger kit $180
no more for smaller jets. i would just swap them out (if i have them)
add $30 more for the Purge. it's also new used 4 or 6 times years ago.
was on this set up.
if i have them (Jets under 125hp set up) add another $35
they run $8.00 ea new, and you need 8 for fuel and 8 for NOS
if you want the jets in kit now and the lower HP Hit jets,
add $30 more for the Purge. it's also new used 4 or 6 times years ago.
was on this set up.
if i have them (Jets under 125hp set up) add another $35
they run $8.00 ea new, and you need 8 for fuel and 8 for NOS
if you want the jets in kit now and the lower HP Hit jets,
Ok cool, thanks for all the info. man. I am supposed to get paid for a job tomorrow, and then I'll hit you up.
#21
Senior Member
iTrader: (7)
Join Date: May 2005
Location: Toronto, Ohio
Posts: 722
Likes: 0
Received 1 Like
on
1 Post
Car: 1991 Trans Am GTA
Engine: 355
Transmission: 4L60
Axle/Gears: 4th gen 10 bolt 3.42 posi
Re: pics.WTS Aluminum Drive Shaft $100 shipped NOS foger kit $180
Just waiting to get paid and figure out what I have to play with. I should be in touch later today with any luck.
#24
Junior Member
Join Date: Apr 2009
Location: Medina, Ohio
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
Car: 89 Sport Coupe Vert (IROC-Z clone)
Engine: 383 Stroker TPI
Transmission: 700r4
Axle/Gears: 2.73 (3.73's awaiting install)
Re: pics.WTS Aluminum Drive Shaft $100 shipped NOS foger kit $180
If Tibo backs out on you I`ll take it. My cash is waiting on you! I actually need it.
#25
Re: pics.WTS Aluminum Drive Shaft $100 shipped NOS foger kit $180
i have sent PM with Paypal info... i always Give them 24 Hrs to do there thing.. so hold tight. and will let you Know..
and remember there is a fee for the Paypal thing..thats them Not me..
Jeff
#27
Re: pics.WTS Aluminum Drive Shaft $100 shipped NOS foger kit $180
just got home from work,tue.9/11/12 funds are good it's going out wed the 12th.
will get you a tracking # about this same time (home from work) wed the 12th.
would have sent it out today...but i was in bed when you sent it..LOL
COULD NOT check my paypal till i got home from work..
Jeff
will get you a tracking # about this same time (home from work) wed the 12th.
would have sent it out today...but i was in bed when you sent it..LOL
COULD NOT check my paypal till i got home from work..
Jeff
Last edited by articwhiteZ; 09-11-2012 at 06:22 PM.
Thread
Thread Starter
Forum
Replies
Last Post
1Aauto
Sponsored Vendors
1
01-15-2016 06:26 AM
1Aauto
Sponsored Vendors
0
09-02-2015 01:35 PM