I dont know what to do on My SLPS 1 3/4 inch headers.I got a quote from HPC for $180 for the two shorties.Feedback please any anywhere I can get my headers coated cheaper?Thanks

 

https://www.thirdgen.org/messgboard/...ML/001708.html

 

Get them coated. The header wrap sucks.

------------------
West Coast GM Shootout 2001!
1991 Camaro Z28
5.7L 5-Speed (originally 305)
13.23 @ 107.62 MPH
Southern California
Member: SoCal 3rd Gen F-Bodies
Webmaster: SoCal F-Bodies
-=ICON Motorsports=-

 

Yeah, LOL!!

 

I got mine done @ Paul Barry Motorsports....cost $220 for both headers, Y-pipe, and shipping. Service and email response was great.

------------------
92 Camaro RS LO3, 5-spd, T-tops
Performance:
SLP 1 3/4" Headers (Coated by Paul Barry Motorsports), Flowmaster Catback Exhaust, Fastchip Performance PROM, Centerforce Dual Friction Clutch, Xact 8mm wires, Open Air Element w/K&N Filter, Z28 Grille w/aftmkt fog lamps
Electronics:
Alpine 8030 Alarm System, Valentine One Radar Detector (How did I ever drive without one?), Pioneer DEH 7450 Head Unit w/6-pack CD changer, Pioneer DEQ 7600 Sound Processor, 2 Kenwood KAC-846 Amps powering 2 12" Pro Red subs, 2 Pioneer 6x9 and 2 MTX 4x6 speakers.
NEXT UP: TBI mods, Edelbrock performer intake

 

Hey procharged go to the J.C whitney catolog and they sell Pace Setters headers for 85-92 camaro/firebirds, there also ceramic coated comes with a 3 inch y pipe and it goes for $369.00 not bad if i say so myself.

------------------
92' camaro
New 305 block TPI conversion, Flat top pistons,Bore over .30 Forged parts all around,Edelbrock intake,ported plennum,ported corvette alluminum heads, accel cam,52mm throttle bodie, SLP runners Home aid cold air induction, Air foil,ford SVO 19lb injectors,fuel regulator,cloys timing chain, comp alluminum roller rocker arms and pushrods MSD 8.5 mm wires, bosch plattinum plugs, hypertech cap & rotor and coil, Edelbrock TES headers, free flowing catalytic converter and a 3 inch force II flowmaster exhaust system, and a 3 inch cutout,Zoom multi friction clutch, T-5 tranny,billenstien shocks&struts.
Soon to come!!!
Procharger system 12lbs o boost.
New paint job(hawaiin orchid purple)Cast alluminum ZR1 rims w/ 275 tires.
Favorite quote: "where ever u go, there u are"

Other car;
1971 plymouth Duster
Mods:340,edelbrock victor jr. intake, 650 4 barrel holley, heddman headers,40 series dual flowmasters, cold air intake,4:10 gears, just got a new paint job and cragar rims with 315 tires in the back.
:Yeah its not a chevy but damn how many 71' dusters have u seen in the streets.

 

http://www.toefco.com/
i think it was them,
I was going to get some hooker shorties coated by them for $150, but ended up going with SLP's and got them and pipes coated for like $200 from jet hot on the GP

------------------
90 IROC 5.7l (L98)
ram air, K&N's, air foil,Flows

LIKE A ROC

 

A guy with a V6 wrapped his headers... after they caught fire, and went through hell getting the car back together, he never used them again. Just something to think about!


------------------
-Tom P (Hot rodded 1986 Firebird 2.8l) from http://www.f-body.net/mailbag/3rd/3rd_mailbag.html message boards
---Think your car could be pic of the week? Visit http://www.f-body.net for details!

 

Send them to jet-hot. If they're new headers, they'll give you a lifetime warranty against rust. Well worth the money.

 

I'm in the process of baking my headers right now. One is in the oven the other will go in as soon as I complete this post. Check out these coatings that you can do yourself. It only cost $25 and the time to prep them and cookem. http://www.techlinecoatings.com/Exhaust.htm

Steve

 

as long as you got an oven that's cool, if not, and still wanta do it yourself, apparently por 20 doesn't need to be baked, someone on here did it, can't remember who though