well after sitting in my back yard for a year and a half, the iroc is almost done, has an hsr swap not with some c6 rims 19X10 rear, 18X8.5 front with 315's rear and 255's up front, still needs alot of work but i like the way it looks with the c6's just needs a fresh coat of paint as the clear coat faded up top



full shot(don't mind my cat)



the c6's with 315's corsas tucks in nicely with 2" drop



just lookign for some friendly criticism, for future mods

 

personally i like the iroc rims and the drop dosent sit well with me, but to each his own. looks like a very clean car. you should add the stripe kit to really make it pop

 

I am not a fan of those wheels on anything.

 

i plan on adding an ss hood when i get a new coat of paint on, but im still workign on the car mechanically, stripes im not sure on that 1 im not into decals nor stipes that is why i removed all the decals & emblems

 

I love those wheels! I need some in 17s.....Drop is not my thing, but definatly looks great on your car!

 

Looks good. Maybe a shot from the back so we can see those 315's tucking?

 

Not a huge fan of the C-6 rims, in fact really don't like them. However WOW looks great. Only Camaro I have EVER seen where I liked them. GOOD JOB, I hope someday my Camaro looks even Close to that good.

Trey

 

Looks good , but it seems the car has alot of orange peel on it already. Might want to really wet sand/buff that out before you repaint it. It might come out real good. w/o a repaint.

 

yeah i kinda figured i could just wet sand an dmaybe a polish would do the car soem justice until paint time rolls around, but the front clip has soem chips so thats why its in need of a new paint job along with the new ss hood i plan on tossing on.

 

i really really like it, post some more pics! what offset are the rears to tuck 315s?

 

correction rear tires are 305's not sure why i had 315 in mind, neways heres a shot of the rear, off set is whatever and oem 19X10 c6 rim is along with a 2" spacer. i had to knock in some of the inner fender wall, clearance is minimal heres a pic

 

im still working with tuning and troubleshooting after the hsr swap, then will come suspension mods including a 4th gen rear end. im kind of already shopping looking to come across a good deal but it's soon to come, still many mods to do not enough time though

 

haha I must of looked at these pictures 6 different times and I'm just now noticing the cat...

I'd put a disk rear end it in to fill out the wheel better. Looks good though.

 

looks pretty good you just need some c6 door handles than it would really set off with those wheels. Do you have any engine bay pics? Do you drive your car much on the street?

 

car has not been driven for about a year and a half now, barely got the car running but i have a small water leak from my intake and are waiting for replacements gasket as well as a few other goodies. has a very rough idle car will not stay running, which i will trouibleshoot once i replace the intake gaskets, heres a shot of the engine bay, stock heads will soon be reaplced by 113 heads and new cam just want to get the car running before i dump ne more money

 

i just noticed that your handles were shaved!

 

yup no handles, nor antenna, i hate 3rd gen handles makes the car look old, i have each window hooked up individually to y alarm, its a hassle but eh... and i've looked into getting poppers for the doors but there damn so heavy,

 

wheels look really really good! the car looks great good choice in color stance and wheels, just redo that $100 paint job down the line.

 

Love all the work you have done...it's definitely a winner. Great color. Maybe a wetsand to make the paint really shine
Love the rims and wire width !

 

Sir your car looks great. What springs are you using? Also do you have pics of the inner fender wells that you had to beat to death?

 

grover85 il take a pic of the inner fender laters. all i did was grab a hammer and begin the pounding, wasnt much but i only have about 1/4" clearence, thats only enough to roll the car but im sure i will need more clearance therefore i will later have to do soem cutting and rewelding, also need to replace my lca's which is the next mod in line to get soem more room, thanks every1 for the complememts, a few more parts arrived from summit yesterday so most important is to do some tunning on the hsr and get the car in good running condition

 

thats a really nice car

 

i have a few questions if you dont mind. i was wonderind what all did you have to do to get those c6 wheels to bolt up? because from what i understand the c5 wheels wont even bolt up. and how much were they?

 

The rims would look beter if they were Chrome. And I thought all Irocs had 4 wheel disc?

 

rims bolted right up just added 2" adapters all the way around, could of maybe used 1.7" in the rear but didnt want to have to cut my inner fender wall(2 much) and i only paid 225 on ebay from a local seller so shipping was free, most expensive and hard to find are the rear 19"wheels. i opted to buy used since 300 a tire is a bit much, and after a month or 2 of looking around my tire shop got me a used but in great shape of pirrelli's for 120 the set hope that helps

 

What kind of springs did you use to drop it 3"?

 

springs are cut, had to do alot of trial and error, it used to sit even lower on my old 17's but the 18's up front raised it up a bit which is good considering i've had clearence issue with the y pipe and constantly having to replace header gaskets, i know dropped isn't every1's style but it sure is mine

 

I seen this car and its really nice. The owner is a cool dude. By the way godreject i finally found an intake on ebay. Thanks for your help! ROC-ON BRO!

 

what he said ROC N ROLL BROTHER!!!

 

Cool i got a set of coilovers & wondering how high I should put them.

 

witch door popper kit did u get ? can u give me a link

 

im actually not using poppers, tacky as it sounds i use my alarm to roll the windows up and down to gain entry to the car, i think its kinda cool to have to reach in to open the door(exept when it rains) but thats hardly ever here in sunny southern cali. i eventually want poppers when i begin driving the car on a regular but with those heavy *** doors im unsure what might work, but shaved is definitely he way to go much cleaner look

 

What size are your tires? 255 & 305/40's?

 

dude, this is the first time i've seen this post. i love it man. car is just clean. not over the top, not over done, not underdone. very well put together. the drop looks great, not like import low, more muscle low. lol. those rims look really nice. i wish they made them in a polished billet aluminum style, instead of just silver or chrome. that would really set it off.

how hard was it to shave the handles? im considering that and my antenna and 3rd BL as well. when i get to that point. haha

anyway. killer car man. keep up the good work.

 

Those rims come in polished aluminum also.