Power Adders Getting a Supercharger or Turbocharger? Thinking about using Nitrous? All forced induction and N2O topics discussed here.

nitrous on ZZ4

Thread Tools
 
Search this Thread
 
Old May 2, 2002 | 10:36 PM
  #1  
Dauntless's Avatar
Thread Starter
Junior Member
20 Year Member
 
Joined: Oct 2001
Posts: 61
Likes: 0
From: Hoover, AL
nitrous on ZZ4

Does anyone know how much nitrous power the ZZ4 engine can hold? It does have a forged crank, but the pistons are silicon coated aluminum. I'd like to spray maybe a 125 shot. Should I just throw in some forged pistons and go with a bigger shot, or could those al. pistons hold that shot? Any thoughts?

Dauntless
Reply
Old May 3, 2002 | 09:54 PM
  #2  
B4Ctom1's Avatar
TGO Supporter
Veteran: Air Force
20 Year Member
 
Joined: Jul 2001
Posts: 4,991
Likes: 1
From: Cheyenne, Wyoming
Car: 1992 B4C 1LE
Engine: Proaction 412, Accel singleplane
Transmission: built 700R4 w/custom converter
Axle/Gears: stock w/later 4th gen torsen pos
Re: nitrous on ZZ4

Originally posted by Dauntless
just throw in some forged pistons and go with a bigger shot Dauntless
sounds good to me and safe too for like 100 to 200 hp shots
Reply
Old May 8, 2002 | 07:34 AM
  #3  
91-ZZ4-Z28's Avatar
Member
 
Joined: May 2001
Posts: 258
Likes: 0
From: Raleigh, NC
If you take all the safety precautions (window switch, good ignition, good plugs, good fuel pump) 125 is fine. But I would not go much higher.
Reply
Old May 8, 2002 | 07:45 AM
  #4  
12 Sec GTA's Avatar
Senior Member
 
Joined: Jan 2002
Posts: 600
Likes: 0
From: orlando
Car: 98 Camaro SS
Engine: LS1
Transmission: M6
125 shouldn't be a problem as long as you don't go lean.
Reply
Old May 8, 2002 | 02:59 PM
  #5  
IROC4LIFE's Avatar
Member
 
Joined: Jan 2001
Posts: 142
Likes: 0
From: In The Garage
Car: 1986 IROC-Z
Engine: SBC
Transmission: Manual Th-350
Axle/Gears: 9" Moser 3.89's Spool.
ZZ4 on Nitrous

The ZZ4 is a pretty tough motor but 125hp shot should be good. Persoanlly I think that a 150hp shot could work well with the proper engine support i.e FUEL PUMP)

When pushing that much HP a MSD 6AL or Equivlent Ignition would be recommended.

Last edited by IROC4LIFE; May 8, 2002 at 03:01 PM.
Reply
Old Mar 17, 2009 | 09:12 PM
  #6  
85ZzZ4's Avatar
Junior Member
 
Joined: Dec 2007
Posts: 29
Likes: 0
From: Indianapolis
Car: 2005 Chevy Colorado/ 1985 Z28
Engine: fast burn zz4
Transmission: th350
Axle/Gears: 10 bolt (has to go) 3:23 gears
Re: nitrous on ZZ4

stirring up an old thread here i know, but did you ever put the 125 shot through the zz4? i'm looking into it too, i tore my fast burn zz4 down this winter and freshened it up a bit... i replaced the rings with the speed pro plazma molly rings just incase i decided to run nitrous... also i have an msd 6A not the 6AL as mentioned above, will that be a problem?
Reply
Old Mar 18, 2009 | 02:39 PM
  #7  
91-ZZ4-Z28's Avatar
Member
 
Joined: May 2001
Posts: 258
Likes: 0
From: Raleigh, NC
Re: nitrous on ZZ4

Originally Posted by 85ZzZ4
stirring up an old thread here i know, but did you ever put the 125 shot through the zz4? i'm looking into it too, i tore my fast burn zz4 down this winter and freshened it up a bit... i replaced the rings with the speed pro plazma molly rings just incase i decided to run nitrous... also i have an msd 6A not the 6AL as mentioned above, will that be a problem?
I sold my car a few years ago but I did run a 125hp Zex dry system system with a Walbro 255lph fuel pump, Ford Motorsport injectors (it's been a few years I can't remember exactly what lbs rating was), MSD window switch, NOS fuel pressure safety switch, Accell high output coil, one step colder plugs, and a custom PROM, .

I never used more than the 50hp jetting because of traction issues (and that was mostly just for testing and to get a good looking dyno sheet but I felt like it would have been fin at 125hp.
Reply
Old Mar 21, 2009 | 07:49 AM
  #8  
85ZzZ4's Avatar
Junior Member
 
Joined: Dec 2007
Posts: 29
Likes: 0
From: Indianapolis
Car: 2005 Chevy Colorado/ 1985 Z28
Engine: fast burn zz4
Transmission: th350
Axle/Gears: 10 bolt (has to go) 3:23 gears
Re: nitrous on ZZ4

thanks, i'm still going back and forth on whether or not i should run nitrous
Reply
Old Mar 21, 2009 | 01:38 PM
  #9  
THE HOFFMEISTER's Avatar
Junior Member
 
Joined: Apr 2007
Posts: 48
Likes: 0
Car: 89 Trans Am GTA
Engine: 350
Transmission: 700r4
Re: nitrous on ZZ4

Nothing to worry about at all.
Just make sure it dont run lean and you will completely fine.
100hp shot easy, should be fine at 150 really, again, just make sure
it dont run lean and it should be fine.
MAke sure your fuel pump is ok, have you a fuel pressure guage?
Reply
Old Mar 21, 2009 | 03:00 PM
  #10  
92droptopws6's Avatar
Senior Member
20 Year Member
Liked
Loved
Community Favorite
iTrader: (10)
 
Joined: Jun 2004
Posts: 915
Likes: 29
From: Las Vegas
Car: '88 Trans Am
Engine: 5.7L TPI
Transmission: Slushbox
Axle/Gears: 3.27
Re: nitrous on ZZ4

sprayed my old ZZ4 for a while on the 150 tune and fuel delivery is everything
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
lt500r55
Tech / General Engine
6
Sep 1, 2021 01:30 PM
italiano67
Tech / General Engine
1
Sep 22, 2015 08:42 AM
anesthes
Power Adders
3
Sep 18, 2015 12:34 PM
Magman
Engine/Drivetrain/Suspension Parts for Sale
0
Sep 13, 2015 12:14 AM
NastyEngines
Group Purchases
4
Sep 8, 2015 10:14 AM




All times are GMT -5. The time now is 08:38 AM.