Nice ride man. Let me ask, what did you need to do in order to delete your MAF sensor ?

 

Factory speed density setup...see upper plenum pass side eear. Map sensor right there.

 

SLP headers/Ramair boxes/Accel 8.8's/Strut brace(Hotchkis)...Super clean.

 

<a href="http://s967.photobucket.com/user/ramzero13/media/2015-07-21%2017.00.56.jpg.html" target="_blank"><img src="http://i967.photobucket.com/albums/ae154/ramzero13/2015-07-21%2017.00.56.jpg" border="0" alt=" photo 2015-07-21 17.00.56.jpg"/></a>

 

Helluva job detailing every nook and cranny zero13. Magnificent.

 

thanks for the words.

 

mine is a bit sloppy, but it works just fine, a nice TPI with valve seals to be replaced. Don't have much money nor time, here in Italy, to bring it new
Does it look nice or bad?

 

Can someone tell me what color the engine would've been from the factory?
'89 in my case.

 

Low gloss black.

 

 

here's my 89 tpi. 355 cu in, 4bolt mains, lt4 hot cam, vortec intake, edelbrock e tec heads, hooker headers, 52 mm TB, Large tube runners, 5 sp, 3.73 posi

 

Thought I'd join the fun!

 

Pardon my rats nest of spark plug wires, something I did back in 1992. She's just now coming out of storage after a long, long rest..... its 99% factory baby! Amazingly, the original hood struts still work!

 

well, I like that!...8996Chevy... ...

 

Hooker Shorty headers, k&n, 8mm spark plug wires, throttle body bypass

 

Lot of nice Tpi setups, I noticed a lot of rubber boots with the stainless piping and was wondering what size adapter you used that fits the throttle body when crushed down (to oval shape). PO put a lt1 elbow on mine but the clamps hit the alternator

 

4"

 

All I can say is wow! I did a very similar paint scheme on my engine but I haven't gotten my block back from the machine shop yet so its not currently assembled but ill be a son of a gun if that don't look awesome !!!

 

 

here is mine

 

TPI in my 85 Volvo

 

88 fast how does the car run with the first intake? Looks great

 

Now that is unique. I like it.

 

How about a fully built, balanced and blueprinted 334 TPI stroker!?

 

Whats you car run? ^^^

 

Not sure yet. Haven't tracked it. Only about 1200 miles on the engine since I built it. Just got the tune finished up.

 

Here's my mostly stock 91 TPI. Cleaned up the engine bay and did so added color touches. The red plenum and dist. cover is a vinyl wrap.

 

May I ask where you got that intake plumbing?

 

Getting mine cleaned up. I got the car on 7/12 and moving right along. New exhaust system too.

This engine bay was pretty messy. I'm about 80% done with the clean up.

 

Improving daily....

 

 

This is how it sits now. FIRST TPI, Hooker 2055's into a full 3 inch exhaust minus the cat (previous owner removed it,) Flowmaster 80. CAI with a SU145 MAF. Runs nice, but you can tell the factory heads and cam don't work well with this intake and exhaust.




This is the pile I have been building up in preparation for my next upgrades. Jegs/Profiler 195 heads, Scorpion narrow body 1.6 RRs, Comp 268 XFI, 2400 stall FTI converter, Dynomax 3" in / dual 3" out muffler to replace the restrictive Flowmaster currently on the car and some nice new tips. All the stuff to finish my "LS1" front brake swap, including Earls SS lines for the whole car. Solid Motor mounts. Accel 300+, Racetronix fuel pump harness and an Aeromotive 340 Stealth to replace my ailing Walbro 255. I also have a set of UMI Sfc's ready to be installed when I get the chance. I am excited to get this stuff installed.

And yeah, My engine bay is well past due for a good cleaning. Been on a few gravel roads lately and it really shows lol.

 

 

How so?

 

It runs fine. Stronger than the stock TPI even. But seat of the pants feels like it is happier in an RPM range that the stock iron L98 heads and cam just can't support. Bit of a loss in off idle torque feel, good mid range push and you can tell it's better on the higher end but that's about when the heads and cam drop off. Something my new heads and cam will do much better with when they get installed.

 

I too have a First intake (not on yet, gonna port and siamese the top half), my fully ported - partly siamese-ed tpi/SLP setup - I rev to 5500 (mhp and e.t. the whole way) and sometimes 5600.

I've got LTs and an open Y-pipe, the sound is LEGENDARY to say the least and leaves people worried and nervous. lol

-Procharger also in the works

 

I have been interested to see how the FIRST does with some boost. I am seriously considering going with a single turbo setup down the road as well. Thats a nice shine on that intake.

 

Yep

 

 

Jj do you have a build thread?
I'm assuming not since this looks like your first post?

 

Here's mine as of July 2017. It's changed a bit through the years! 383 with all the good stuff

...details are on the car's Facebook page in my sig below.