HELP...running many codes
Thread Starter
Supreme Member
Joined: Mar 2000
Posts: 1,777
Likes: 0
From: First one out of liberty city, burn it to the ground
HELP...running many codes
running codes 22, 32, and 34. I have a new MAF, TPS on there. Started today. Wont idle unless i unplug the MAF and when i do it will save itself instead of just dying. IDEAS? I need the car soon!
------------------
1989 Firebird
2.8 v6, t5 swapped in
Ram Hi-po clutch, Cold Air, 1.6 rockers (ready to install), Lakewood LCA's, Lakewood Lift bars, 3" y-pipe, Random Tech Cat, 3" I-pipe, Flowmasters, MSd 6a, MSD Coil (Fireball in future) Accel 8.8 wires, MSD Ignition Module, 4th Gen Seats (not front yet)
" I'd rather run last in a full out race, than to NOT run at all ".
------------------
1989 Firebird
2.8 v6, t5 swapped in
Ram Hi-po clutch, Cold Air, 1.6 rockers (ready to install), Lakewood LCA's, Lakewood Lift bars, 3" y-pipe, Random Tech Cat, 3" I-pipe, Flowmasters, MSd 6a, MSD Coil (Fireball in future) Accel 8.8 wires, MSD Ignition Module, 4th Gen Seats (not front yet)
" I'd rather run last in a full out race, than to NOT run at all ".
Thread Starter
Supreme Member
Joined: Mar 2000
Posts: 1,777
Likes: 0
From: First one out of liberty city, burn it to the ground
btt
------------------
1989 Firebird
2.8 v6, t5 swapped in
Ram Hi-po clutch, Cold Air, 1.6 rockers (ready to install), Lakewood LCA's, Lakewood Lift bars, 3" y-pipe, Random Tech Cat, 3" I-pipe, Flowmasters, MSd 6a, MSD Coil (Fireball in future) Accel 8.8 wires, MSD Ignition Module, 4th Gen Seats (not front yet)
" I'd rather run last in a full out race, than to NOT run at all ".
------------------
1989 Firebird
2.8 v6, t5 swapped in
Ram Hi-po clutch, Cold Air, 1.6 rockers (ready to install), Lakewood LCA's, Lakewood Lift bars, 3" y-pipe, Random Tech Cat, 3" I-pipe, Flowmasters, MSd 6a, MSD Coil (Fireball in future) Accel 8.8 wires, MSD Ignition Module, 4th Gen Seats (not front yet)
" I'd rather run last in a full out race, than to NOT run at all ".
Moderator
Joined: Jan 2000
Posts: 19,655
Likes: 309
Graeme,
The '22' is a poor connection to the MAT sensor, the '32' is an EGR fault, and teh '34' is a MAF low-flow error. Either you've lost connections to several sensors, of the ECM edge connector is coming loose from the ECM. Check and clean all connections, test the TPS voltage, and clear the error codes (reinitialize the ECM). Report back with results.
------------------
Later,
Vader
------------------
"I'm'a do Things My Way - It's My way or the Highway."
Adobe Acrobat Reader
The '22' is a poor connection to the MAT sensor, the '32' is an EGR fault, and teh '34' is a MAF low-flow error. Either you've lost connections to several sensors, of the ECM edge connector is coming loose from the ECM. Check and clean all connections, test the TPS voltage, and clear the error codes (reinitialize the ECM). Report back with results.
------------------
Later,
Vader
------------------
"I'm'a do Things My Way - It's My way or the Highway."
Adobe Acrobat Reader
Thread
Thread Starter
Forum
Replies
Last Post
