Anyone know what size they are. I heard some time ago someone actually bought a set from sears. I forgot was size it was. Lost all mines. Anyway any one know what size they are. Do u think sears will sell screws to fit the runner and plennum?? any imput.

------------------
92' camaro
New 305 block TPI conversion, Flat top pistons,Bore over .30 Forged parts all around,Edelbrock intake,ported plennum,ported corvette alluminum heads, accel cam,52mm throttle bodie, SLP runners Home aid cold air induction, Air foil,ford SVO 19lb injectors,fuel regulator,cloys timing chain, comp alluminum roller rocker arms and pushrods MSD 8.5 mm wires, bosch plattinum plugs, hypertech cap & rotor and coil, Edelbrock TES headers, free flowing catalytic converter and a 3 inch force II flowmaster exhaust system, and a 3 inch cutout,Zoom multi friction clutch, T-5 tranny,billenstien shocks&struts.
Soon to come!!!
Procharger system 12lbs o boost.
New paint job(hawaiin orchid purple)Cast alluminum ZR1 rims w/ 275 tires.
Favorite quote: "where ever u go, there u are"

Other car;
1971 plymouth Duster
Mods:340,edelbrock victor jr. intake, 650 4 barrel holley, heddman headers,40 series dual flowmasters, cold air intake,4:10 gears, just got a new paint job and cragar rims with 315 tires in the back.
:Yeah its not a chevy but damn how many 71' dusters have u seen in the streets.

 

I bought a complete set of Stainless, Allen Head bolts from Ebay. There is a guy that auctions the kits, and they usually go for about $20. It comes w/ all 12 lower intake, all runner bolts, all 7 IAC housing bolts, all four TB bolts, all the TPI emblem bolts, the three bolts for the distibuter cover, the three bolts for the throttle/TV/Cruise cable brackets. They look really good.

You might be able to see them in this pic:



------------------
If you live in Southeastern US, check us out!
South East Thirdgen

GM Master Tech
ASE Master Tech + L1
Savannah, GA

'87 Trans Am
S/D TPI retrofit including functional PassKey,
22# injectors,
Whatever chip I feel like burning,
JET AFPR, Ported Plenum,
TB Coolant Bypass, Custom Cold Air,
SSM SFC, KYB Shocks, Boxed LCAs, Wonder Bar,
8mm Accel wires,
Flowmaster Exhaust,
16" GTA rims,
Corvette Servo,
-->14.97 @ 94.9 MPH<--

'97 Bonneville SSE

[This message has been edited by GMTech (edited April 01, 2001).]

 

anyone else. cant get through

 

The dealer still has them.... if you want the stock ones. I picked some up about 2 months ago.

------------------
Kevin Irving
85 Trans Am WS-6, 305 TPI, custom burned '86 PROM with '87 "165"ECM, Accel Supercoil & 8.8 Wires, MSD 6AL, Aluminum Driveshaft, Wonderbar, TB Coolant Bypass, Ported Plenum, Modified MAF, Syclone Fuel Pump, JET Airfoil

15.556 @ 86.65mph, Nov 10, 2000.... I know it sucks.. but it will get better!

http://www.geocities.com/transam85tpi/

Member - The Tidewater Trans Am Club, Norfolk VA http://www.geocities.com/ttacva/

 

How much did u pay for it.

------------------
92' camaro
New 305 block TPI conversion, Flat top pistons,Bore over .30 Forged parts all around,Edelbrock intake,ported plennum,ported corvette alluminum heads, accel cam,52mm throttle bodie, SLP runners Home aid cold air induction, Air foil,ford SVO 19lb injectors,fuel regulator,cloys timing chain, comp alluminum roller rocker arms and pushrods MSD 8.5 mm wires, bosch plattinum plugs, hypertech cap & rotor and coil, Edelbrock TES headers, free flowing catalytic converter and a 3 inch force II flowmaster exhaust system, and a 3 inch cutout,Zoom multi friction clutch, T-5 tranny,billenstien shocks&struts.
Soon to come!!!
Procharger system 12lbs o boost.
New paint job(hawaiin orchid purple)Cast alluminum ZR1 rims w/ 275 tires.
Favorite quote: "where ever u go, there u are"

Other car;
1971 plymouth Duster
Mods:340,edelbrock victor jr. intake, 650 4 barrel holley, heddman headers,40 series dual flowmasters, cold air intake,4:10 gears, just got a new paint job and cragar rims with 315 tires in the back.
:Yeah its not a chevy but damn how many 71' dusters have u seen in the streets.

 

8mm x 1.25 thread.

Available at any Ace Hardware.



------------------
Kelly 'GhoSSt' Rosato
1996 Impala SS, 383 LT4 (14.65 up here, 13.24 lower)
1984 Firebird, +.060 350 (Vortech Heads, HOT Cam, and schtuff)
1993 Caprice, 5.7 TBI (stock . . . FOR NOW)

"And if you wrong us, shall we not revenge? Revenge. The villany you
teach me, I will execute, and it shall go hard but I will better the
instruction."

Shylock in Act III, Scene I of 'Merchant of Venice' by William Shakespeare

 

ah crap theres no ACE hardware from where i live at least i dont think so. U think they sell those screws at sears or any other hardware.

 

I got the same ones, and they go for about $30-40. They're a good set of bolts!


------------------
West Coast GM Shootout 2001!
1991 Camaro Z28
5.7L 5-Speed (originally 305)
13.25 @ 107.18 MPH
Southern California
Member: SoCal 3rd Gen F-Bodies
Webmaster: SoCal F-Bodies
-=ICON Motorsports=-

 

Kevin, the guy either got wise as to what he could actually get for them, or I just got lucky, because I won the auction at $20 plus shipping. I think the company was Rolling Thunder Classics, or something like that.

------------------
If you live in Southeastern US, check us out!
South East Thirdgen

GM Master Tech
ASE Master Tech + L1
Savannah, GA

'87 Trans Am
S/D TPI retrofit including functional PassKey,
22# injectors,
Whatever chip I feel like burning,
JET AFPR, Ported Plenum,
TB Coolant Bypass, Custom Cold Air,
SSM SFC, KYB Shocks, Boxed LCAs, Wonder Bar,
8mm Accel wires,
Flowmaster Exhaust,
16" GTA rims,
Corvette Servo,
--&gt;14.97 @ 94.9 MPH&lt;--

'97 Bonneville SSE