Can someone tell me step by step how to install new rockers?
Thread Starter
Supreme Member
iTrader: (8)
Joined: Jan 2000
Posts: 3,968
Likes: 1
From: Macedonia ,OH
Car: Formula
Engine: 6.0 LSX
Transmission: 4L60E
Axle/Gears: 9 Bolt 3:27
Can someone tell me step by step how to install new rockers?
I got the Comp Pro Mags. I didnt get the full roller ones, cause I got these cheap. Thanks its on a 350 TPI
Joined: Mar 2000
Posts: 43,187
Likes: 46
From: Littleton, CO USA
Car: 82 Berlinetta/57 Bel Air
Engine: L92/LQ4 (both w/4" stroke)
Transmission: 4L80E/4L80E
Axle/Gears: 12B-3.73/9"-3.89
Remove whatever is in the way of removing the valve covers, then remove the valve covers.
Unscrew the 1st rocker, remove rocker, ball, & nut. Oil up and install new rocker, ball & nut (this would be a good time for new push rods), tighten approximately to point of removed rocker. Repeat for remaining 15.
Adjust the rockers by the book. I'd repeat what the book says, but I'm about 656 miles away from my book right now.
Clean old gasket from valve covers & heads, install new gaskets, replace covers and whatever you removed to get to them.
------------------
82 Berlinetta, orig V-6 car, now w/86 LG4/TH700R. 2.93 limited slip. Cat-back from '91 GTA, Accel HEI SuperCoil. AMSOIL syn lubes bumper-to-bumper. Daily driver, work-in-progress (LG4 w/'87 LB9 block, ZZ3 cam and intake, World 305 heads, Hooker headers & y-pipe, 3" Catco cat).
57 Bel Air, my 1st car. 0.030 over 396, Weiand Action+, Edelbrock 1901 Q-Jet, Jacobs Omnipack, 1-3/4" Hedders, TH400 w/TCI Sat Night Special conv & Trans-Scat shift kit, 3.08 8.2" 10-bolt w/Powertrax, AMSOIL syn lubes bumper-to-bumper. Best 15.1 @ 5800' Bandimere w/open diff & slipping tranny. Daily driver while Camaro was being put together.
[This message has been edited by five7kid (edited April 11, 2001).]
Unscrew the 1st rocker, remove rocker, ball, & nut. Oil up and install new rocker, ball & nut (this would be a good time for new push rods), tighten approximately to point of removed rocker. Repeat for remaining 15.
Adjust the rockers by the book. I'd repeat what the book says, but I'm about 656 miles away from my book right now.
Clean old gasket from valve covers & heads, install new gaskets, replace covers and whatever you removed to get to them.
------------------
82 Berlinetta, orig V-6 car, now w/86 LG4/TH700R. 2.93 limited slip. Cat-back from '91 GTA, Accel HEI SuperCoil. AMSOIL syn lubes bumper-to-bumper. Daily driver, work-in-progress (LG4 w/'87 LB9 block, ZZ3 cam and intake, World 305 heads, Hooker headers & y-pipe, 3" Catco cat).
57 Bel Air, my 1st car. 0.030 over 396, Weiand Action+, Edelbrock 1901 Q-Jet, Jacobs Omnipack, 1-3/4" Hedders, TH400 w/TCI Sat Night Special conv & Trans-Scat shift kit, 3.08 8.2" 10-bolt w/Powertrax, AMSOIL syn lubes bumper-to-bumper. Best 15.1 @ 5800' Bandimere w/open diff & slipping tranny. Daily driver while Camaro was being put together.
[This message has been edited by five7kid (edited April 11, 2001).]
Thread
Thread Starter
Forum
Replies
Last Post
ambainb
Camaros for Sale
11
Apr 25, 2016 09:21 PM
IrocZ'85
Engine/Drivetrain/Suspension Parts for Sale
0
Aug 17, 2015 06:24 PM
