car kind of studders and jerks at WOT
#1
Senior Member
Thread Starter
Join Date: Apr 2001
Location: waukesha, WI USA
Posts: 668
Likes: 0
Received 0 Likes
on
0 Posts
car kind of studders and jerks at WOT
what could it be, i dont think its int he drivetran, i replaced u-joings and everything seems to be ok, what can i check?
#3
Senior Member
Thread Starter
Join Date: Apr 2001
Location: waukesha, WI USA
Posts: 668
Likes: 0
Received 0 Likes
on
0 Posts
Trent
---Car---
1990 Camaro IROC-Z / 350 GM Crate/TH400 Tranny/B&M Shift Kit & Mega Shifter/K&N/3.73 *** gears/Adj Fuel Pressure reg/ Air Dam/ Crazy Bitch Scratches
---Car---
1990 Camaro IROC-Z / 350 GM Crate/TH400 Tranny/B&M Shift Kit & Mega Shifter/K&N/3.73 *** gears/Adj Fuel Pressure reg/ Air Dam/ Crazy Bitch Scratches
#7
Member
Join Date: Sep 2001
Location: winter springs, FL
Posts: 484
Likes: 0
Received 1 Like
on
1 Post
Car: 2006 Pontiac GTO
Transmission: rowing through 6 gears
had this problem on my car and the problem was that one of the positive wires running down the starter had gotten pressed against the header and was arcing against my header.
Trending Topics
#9
Senior Member
Thread Starter
Join Date: Apr 2001
Location: waukesha, WI USA
Posts: 668
Likes: 0
Received 0 Likes
on
0 Posts
#12
Member
Join Date: Sep 2001
Location: winter springs, FL
Posts: 484
Likes: 0
Received 1 Like
on
1 Post
Car: 2006 Pontiac GTO
Transmission: rowing through 6 gears
i agree with that one too... i had to replace my ignition module but i didnt find out it was my problem until i was at the tracka nd it took a complete poop on me. one AAA tow ride and about 30 bucks later i was good to go.
#15
Member
Join Date: Sep 2001
Location: winter springs, FL
Posts: 484
Likes: 0
Received 1 Like
on
1 Post
Car: 2006 Pontiac GTO
Transmission: rowing through 6 gears
ill try and explain the installation as best i can remember...
undo the two screws that hold down the cap and pull the cap off. the ignition module is at the back of the distributor and there are two wires going to it i believe (might be one). unscrew the ignition module and replace it with the new one (be sure to apply the grease that comes with the new one). reinstall everything else. its really not that hard except it takes some small hands which i dont have but luckily my dad does.
undo the two screws that hold down the cap and pull the cap off. the ignition module is at the back of the distributor and there are two wires going to it i believe (might be one). unscrew the ignition module and replace it with the new one (be sure to apply the grease that comes with the new one). reinstall everything else. its really not that hard except it takes some small hands which i dont have but luckily my dad does.
#16
trent 257 this is susjam I've bought and paid for the parts I requested from you, have not seen the parts and you will not respond to email........I'm sure there is a good explaination, email me asap
Thread
Thread Starter
Forum
Replies
Last Post
novaderrik
Transmissions and Drivetrain
3
08-10-2015 12:44 PM