where's an article on modifing a LT1 intake for an older small block
Thread Starter
Member
Joined: Nov 2001
Posts: 125
Likes: 0
From: Blue Mountain, MS, US
where's an article on modifing a LT1 intake for an older small block
I was surfing the internet the other day and I saw a topic where they were telling how to modify a LT1 intake to fit a older small block.
I thought I book marked it, but didn't. It was on one of these gm sites. Could any body tell me were it is?
I thought I book marked it, but didn't. It was on one of these gm sites. Could any body tell me were it is?
Member
Joined: Dec 2000
Posts: 437
Likes: 1
From: Jacksonville ,Fl
Here ya go
http://sethirdgen.org/LT1.htm
http://sethirdgen.org/LT1.htm
Senior Member
Joined: Jul 1999
Posts: 851
Likes: 1
From: Shelby Twp., Mi., USA
Car: '84 Fiero ('01 GA interior)
Engine: '96 4.0 Aurora
Transmission: '96 4T80E
Find the original here: http://members.home.net/millicanga/ on John Millican's website.
Supreme Member
Joined: Jul 1999
Posts: 2,767
Likes: 2
From: Vereinigten Staaten
Car: Take
Engine: Your
Transmission: Pick
Its just about the same thing.
------------------
If you live in Southeastern US, check us out!
South East Thirdgen
1987 Trans Am 305
14.88 @ 92.81
[This message has been edited by GMTech (edited November 13, 2001).]
------------------
If you live in Southeastern US, check us out!
South East Thirdgen
1987 Trans Am 305
14.88 @ 92.81
[This message has been edited by GMTech (edited November 13, 2001).]
Supreme Member
iTrader: (1)
Joined: Feb 2000
Posts: 2,361
Likes: 1
From: Savannah, GA
Car: 1997 Jeep Wrangler
Engine: 4.0L
Transmission: 5 speed
Axle/Gears: 8.8 rear, 4.56 gears, 4:1 transfer
------------------
86 Camaro Sport
LT1 Induction
383 Speed-O-Motive Crate Engine, Raptor 700R4 Tranmission, Trick Flow Twisted Wedge G2's, 58mm Accel TB, 3.73 Auburn Pro, SLP Cold Air Induction and Headers, Hooker Cat-back, Serpentine Belt Setup, Dual IROC Fans, Jamex springs, 16" IROC Rims, 36mm/24mm Sway Bars, Global West Steering Brace. Hotchkis Rear LCA's,Panhard Bar and SFC's.
My Camaro Project
Moderator at SE ThirdGen
Trending Topics
Thread Starter
Member
Joined: Nov 2001
Posts: 125
Likes: 0
From: Blue Mountain, MS, US
Hey John,
will I need the LT1 fuel rails also or will my tuneport rail fit?
What about the throttlebody will the tuneport fit or do I need the LT1 throttlebody?
[This message has been edited by zboss86 (edited November 14, 2001).]
will I need the LT1 fuel rails also or will my tuneport rail fit?
What about the throttlebody will the tuneport fit or do I need the LT1 throttlebody?
[This message has been edited by zboss86 (edited November 14, 2001).]
Supreme Member
iTrader: (1)
Joined: Feb 2000
Posts: 2,361
Likes: 1
From: Savannah, GA
Car: 1997 Jeep Wrangler
Engine: 4.0L
Transmission: 5 speed
Axle/Gears: 8.8 rear, 4.56 gears, 4:1 transfer
<font face="Verdana, Arial" size="2">Originally posted by zboss86:
Hey John,
will I need the LT1 fuel rails also or will my tuneport rail fit?
What about the throttlebody will the tuneport fit or do I need the LT1 throttlebody?
</font>
Hey John,
will I need the LT1 fuel rails also or will my tuneport rail fit?
What about the throttlebody will the tuneport fit or do I need the LT1 throttlebody?
</font>
You can use either the TPI TB or the LT1 TB.
[This message has been edited by John Millican (edited November 14, 2001).]
Thread Starter
Member
Joined: Nov 2001
Posts: 125
Likes: 0
From: Blue Mountain, MS, US
Is there any specific sensors I'll need when I find an intake? I'm not sure what came with the LT1 intake. I see alot of bare intakes. I can get the fuelrails seperate. It's getting hard to find a complete LT1 intake.
I still have the sensors on the Tuneport intake. I don't know if there the same.
I won't be running egr. I'll also be running fel-pro speed-pro unit.
I still have the sensors on the Tuneport intake. I don't know if there the same.
I won't be running egr. I'll also be running fel-pro speed-pro unit.
Supreme Member
Joined: Jul 1999
Posts: 2,767
Likes: 2
From: Vereinigten Staaten
Car: Take
Engine: Your
Transmission: Pick
<font face="Verdana, Arial" size="2">Originally posted by zboss86:
What about the throttlebody will the tuneport fit or do I need the LT1 throttlebody?
</font>
What about the throttlebody will the tuneport fit or do I need the LT1 throttlebody?
</font>
Depends on what throttle cable you want to use. If you use the TPI Throttle body, you can use the stock throttle cable. If you use the LT1 throttle body, you will have to buy the LT1 throttle cable. John and I found this out the hard way. If you need an LT1 throttle cable, I have one for cheap!
------------------
If you live in Southeastern US, check us out!
South East Thirdgen
1987 Trans Am 305
14.88 @ 92.81
Thread
Thread Starter
Forum
Replies
Last Post
9192camaro
Engine/Drivetrain/Suspension Parts for Sale
16
Feb 3, 2019 12:21 AM
theshackle
Tech / General Engine
4
Mar 5, 2017 06:37 PM
Fast355
DFI and ECM
14
Dec 2, 2016 06:33 PM
Mickeyruder
Engine/Drivetrain/Suspension Parts for Sale
3
Sep 2, 2015 02:45 PM
