Need new C-clips
Thread Starter
Supreme Member
iTrader: (1)
Joined: Jul 2004
Posts: 10,763
Likes: 4
From: Calgary, AB, Canada
Car: 1982 Trans-Am
Engine: 355 w/ ported 416s
Transmission: T10, hurst shifter
Axle/Gears: 10 bolt, true-trac, 3.73
Need new C-clips
I managed to lose my C-clips when I was rebuilding my 10 bolt 
Napa and Parts source don't sell these, and I have no idea who would, since it's really not a wear part.
Anyone know who sells them? I really (really!) don't want to go JY diving for these in january. (Although I do remember leaving a set on the ground a few times at the yard...)
Or if anyone is junking their 10 bolt right now, and is willing to toss their c-clips in an envelope and send it to me i'd go for that.
Thanks

Napa and Parts source don't sell these, and I have no idea who would, since it's really not a wear part.
Anyone know who sells them? I really (really!) don't want to go JY diving for these in january. (Although I do remember leaving a set on the ground a few times at the yard...)
Or if anyone is junking their 10 bolt right now, and is willing to toss their c-clips in an envelope and send it to me i'd go for that.

Thanks
Joined: Aug 1999
Posts: 19,282
Likes: 103
From: Lawrence, KS
Car: Met. Silver 85 IROC/Sold
Engine: 350 HO Deluxe (350ci/330hp)
Transmission: T-5 (Non-WC)
Axle/Gears: Limited Slip 3.23's
Re: Need new C-clips
GM p/n 344171. GMPartsDirect still shows it as good.
JamesC
JamesC
Joined: Sep 2005
Posts: 27,881
Likes: 2,434
Car: Yes
Engine: Usually
Transmission: Sometimes
Axle/Gears: Behind me somewhere
Thread Starter
Supreme Member
iTrader: (1)
Joined: Jul 2004
Posts: 10,763
Likes: 4
From: Calgary, AB, Canada
Car: 1982 Trans-Am
Engine: 355 w/ ported 416s
Transmission: T10, hurst shifter
Axle/Gears: 10 bolt, true-trac, 3.73
Re: Need new C-clips
Thanks! I'll try my local stealership if they're open tomorrow, or else a drivetrain specialty place in town. I get really annoyed when I have to drive 20kms across town for a $2 part, especially with the frequency of that situation...
Re: Need new C-clips
The C clip solution is a piece of s#&% to say it mildly ;P
I mounted the Moser C-clip eliminator on my Gm10bolt, with the Auburn differential, runs like a champ, and tight as it should be , with NO sideways movement at all....
I mounted the Moser C-clip eliminator on my Gm10bolt, with the Auburn differential, runs like a champ, and tight as it should be , with NO sideways movement at all....
Thread Starter
Supreme Member
iTrader: (1)
Joined: Jul 2004
Posts: 10,763
Likes: 4
From: Calgary, AB, Canada
Car: 1982 Trans-Am
Engine: 355 w/ ported 416s
Transmission: T10, hurst shifter
Axle/Gears: 10 bolt, true-trac, 3.73
Re: Need new C-clips
Well yea, but for close to $200 I could get something that adds zero functionality to my rear end so.... I can't really justify that.
Thread
Thread Starter
Forum
Replies
Last Post
enigma57
Transmissions and Drivetrain
2
Apr 12, 2001 08:50 PM










