Third Generation F-Body Message Boards
0 2015/08/22 08:08:31
0 2015/08/22 08:08:43
0 2015/08/22 08:08:47
First cut, just sort of randomly placed.
First cut, just sort of randomly placed.
0 2015/09/01 19:03:03
I think this is about 90% done. Just clean up left.
I think this is about 90% done. Just clean up left.
0 2015/09/01 19:03:12
What the passenger side wheel well looks like. Again, about 90% complete cutting I think.
What the passenger side wheel well looks like. Again, about 90% complete cutting I think.
0 2015/09/01 19:03:19
Passenger side rear shot of wheel well.
Passenger side rear shot of wheel well.
0 2015/09/01 19:03:25
Wolfe minitub kit component test fit into place. No idea if this is mounted at the correct height.
Wolfe minitub kit component test fit into place. No idea if this is mounted at the correct height.
0 2015/09/01 19:03:31
Shot from above inside the car. I think I will have to go a bit wider still. Again about 90% done.
Shot from above inside the car. I think I will have to go a bit wider still. Again about 90% done.
0 2015/09/01 19:03:38
First test fit from above. I think I will need to go a bit wider.
First test fit from above. I think I will need to go a bit wider.
0 2015/09/01 19:21:29
First test fit of Wolfe minitub kit ps side piece.
First test fit of Wolfe minitub kit ps side piece.
0 2015/09/01 19:21:36
ps rear about 90% cut out.
ps rear about 90% cut out.
0 2015/09/01 19:21:43
ps about 90% done.
ps about 90% done.
0 2015/09/01 19:21:52
Front ps, I think about 90% done.
Front ps, I think about 90% done.
0 2015/09/01 19:22:01
First cut to get this thing started.
First cut to get this thing started.
0 2015/09/01 19:22:08
0 2015/10/27 18:10:42
Griffin LS swap 19 x 31 universal combo unit test fit.
Griffin LS swap 19 x 31 universal combo unit test fit.
0 2017/10/03 18:37:45
left side of core support vertical brace trimmed slightly. Needed more cleanse on the passenger side tube outlet. Looks ok now.
left side of core support vertical brace trimmed slightly. Needed more cleanse on the passenger side tube outlet. Looks ok now.
0 2017/10/03 18:39:09
Shot from below. You can see I already started to trim the core support. Center section is cut. Rust and horrible old brackets were welded there. Happy that cancer is gone. All the blue tape represents metal I am considering cutting. What do you guts think? Should be ok.
Shot from below. You can see I already started to trim the core support. Center section is cut. Rust and horrible old brackets were welded there. Happy that cancer is gone. All the blue tape represents metal I am considering cutting. What do you guts think? Should be ok.
0 2017/10/03 18:40:40
0 2017/10/04 13:00:07
0 2017/10/04 13:00:13
0 2017/10/09 04:35:21
0 2017/10/10 17:47:14
Tried using this HF 18" metal brake. Didn't work at all to bend 16 gauge steel. Returned it and fabricated the parts on my trusty bench vice.
Tried using this HF 18" metal brake. Didn't work at all to bend 16 gauge steel. Returned it and fabricated the parts on my trusty bench vice.
0 2017/10/15 04:18:58
PS tacked in place fitment checking.
PS tacked in place fitment checking.
0 2017/10/15 04:21:41
Same with DS.
Same with DS.
0 2017/10/15 04:22:58
Shot of the major work complete.
Shot of the major work complete.
0 2017/10/15 04:24:13
All welded, and cleaned up ready to anti rust paint that will go on before epoxy primer to help prevent rust. Eastwood rust encapsulator. Nice because it is thin so it will run between the side sand lower panels. Will sand accessible areas later before applying epoxy primer.
All welded, and cleaned up ready to anti rust paint that will go on before epoxy primer to help prevent rust. Eastwood rust encapsulator. Nice because it is thin so it will run between the side sand lower panels. Will sand accessible areas later before applying epoxy primer.
0 2017/10/15 04:26:12
Two coats
Two coats
0 2017/10/15 04:30:08
DS
DS
0 2017/10/15 04:30:49
PS
PS
0 2017/10/15 04:31:35
Fitment of the radiator on the new lower core support.
Fitment of the radiator on the new lower core support.
0 2017/10/15 15:22:33
Lower hose clearance seems like it will be ok. This pic makes it look much closer than it is.
Lower hose clearance seems like it will be ok. This pic makes it look much closer than it is.
0 2017/10/15 15:25:05
0 2017/10/31 09:04:50
0 2017/11/07 13:36:44
From basement where compressors are, got plumbed to garage. Top feed is filtered, then desicant/ filtered, then I use a disposable filter on the gun. Lower run is for general use
From basement where compressors are, got plumbed to garage. Top feed is filtered, then desicant/ filtered, then I use a disposable filter on the gun. Lower run is for general use
0 2017/12/11 07:10:43
Craftsman and HF plumbed together, powered on different circuits.
Craftsman and HF plumbed together, powered on different circuits.
0 2017/12/11 07:11:04
Rear frame rail bar to cross tie and corner gusset bar.
Rear frame rail bar to cross tie and corner gusset bar.
0 2018/01/15 05:38:31
Just showing what is going on underneath as a reminder.
Just showing what is going on underneath as a reminder.
0 2018/01/15 05:39:34
0 2018/02/20 07:58:28