Auto Detailing and Appearance Share tips and tricks on how to make your Third Gen shine! Get opinions on products or how something tasteful looks on your Chevrolet Camaro or Pontiac Firebird.

Firebird 6" thick parts book

Thread Tools
 
Search this Thread
 
Old Mar 1, 2003 | 09:31 AM
  #1  
joshp14's Avatar
Thread Starter
Supreme Member
 
Joined: Sep 2002
Posts: 1,834
Likes: 0
From: Norwalk, Iowa
Firebird 6" thick parts book

Novass has bought the book from me, so he will now be taking over these fullfillments. Thanks!

I aquired a 6" thick parts and illustrations manual from an old pontiac dealer. It covers all Firebirds, Formula's, and Trans Am's for the third generation (82-92). It has every part number known to man for every firebird car between 82-92. The book weighs in at 13 Ibs.

So if you need any GM part number for any reason for any firebird, let me know. I just got this book so I will have to learn how to use it cause it's almost 2,000 pages.
Attached Thumbnails Firebird 6" thick parts book-bk1.jpg  

Last edited by joshp14; Jan 5, 2005 at 05:59 PM.
Reply
Old Mar 1, 2003 | 10:59 AM
  #2  
lock's Avatar
Senior Member
 
Joined: Jul 1999
Posts: 768
Likes: 0
From: Concord, NC
Car: 86 IROC-Z
Engine: Superramed 355 w/ intercooled T72
Transmission: T56 -=- www.iroc-ss.com
Need GM part number for the Idle Air Control sensor and the Throttle Position Sensor on an 85 IROC (305 tpi)
Reply
Old Mar 1, 2003 | 10:26 PM
  #3  
joshp14's Avatar
Thread Starter
Supreme Member
 
Joined: Sep 2002
Posts: 1,834
Likes: 0
From: Norwalk, Iowa
Originally posted by lock
Need GM part number for the Idle Air Control sensor and the Throttle Position Sensor on an 85 IROC (305 tpi)
IAC Valve - 17111288
TPS - 17111606

NOTE: These #'s are for Firebird, but since the 1985 LB9 is the same, I am 99% sure that these numbers are correct for the Iroc as well.
Reply
Old Mar 1, 2003 | 10:35 PM
  #4  
TimRS's Avatar
Senior Member
25 Year Member
Liked
 
Joined: Sep 2000
Posts: 699
Likes: 32
From: McDonough, GA
Car: 1991 Camaro RS
Engine: 305 TBI
Transmission: 700R4
Axle/Gears: 3.42
Josh, how about a part number for the distributor cover that mounts at the rear of a TPI plenum for a 1990. Will the book tell you if it's the plastic or aluminum cover? Thanks.
Reply
Old Mar 1, 2003 | 10:41 PM
  #5  
83crossfireZ28's Avatar
Member
 
Joined: Dec 2002
Posts: 195
Likes: 0
ive got the 82 - 85 parts book for camaros... and my dad has hundreds of parts books and thousands of shop manuals...
Reply
Old Mar 1, 2003 | 10:53 PM
  #6  
joshp14's Avatar
Thread Starter
Supreme Member
 
Joined: Sep 2002
Posts: 1,834
Likes: 0
From: Norwalk, Iowa
Originally posted by TimRS
Josh, how about a part number for the distributor cover that mounts at the rear of a TPI plenum for a 1990. Will the book tell you if it's the plastic or aluminum cover? Thanks.
Well, since f-bodies didnt come with aluminum plenum extensions, it wont be in this book, so it only lists the plastic one. However, the corvette did use the aluminum extension, and i do have that part number. I will give you the plastic and aluminum one:

*Keep in mind that the aluminum extension uses different screws than the plastic one.

Plastic Extension - 14083696
Screws for plastic extension(3X) - 14083852

Aluminum Extension - 10108425
Screws for aluminum extension(3X) - 14082425

Hope this helps.

-Josh
Reply
Old Mar 1, 2003 | 10:56 PM
  #7  
TimRS's Avatar
Senior Member
25 Year Member
Liked
 
Joined: Sep 2000
Posts: 699
Likes: 32
From: McDonough, GA
Car: 1991 Camaro RS
Engine: 305 TBI
Transmission: 700R4
Axle/Gears: 3.42
Thanks Josh...and yes it helps alot.
Reply
Old Mar 1, 2003 | 11:48 PM
  #8  
joshp14's Avatar
Thread Starter
Supreme Member
 
Joined: Sep 2002
Posts: 1,834
Likes: 0
From: Norwalk, Iowa
no prob, anyone else? i am willing to help, so keep this thread in mind.
Reply
Old Mar 1, 2003 | 11:50 PM
  #9  
lock's Avatar
Senior Member
 
Joined: Jul 1999
Posts: 768
Likes: 0
From: Concord, NC
Car: 86 IROC-Z
Engine: Superramed 355 w/ intercooled T72
Transmission: T56 -=- www.iroc-ss.com
Thanks! Cant seem to find that IAC part number onthe GM parts sites though .
Reply
Old Mar 2, 2003 | 12:03 AM
  #10  
joshp14's Avatar
Thread Starter
Supreme Member
 
Joined: Sep 2002
Posts: 1,834
Likes: 0
From: Norwalk, Iowa
Originally posted by lock
Thanks! Cant seem to find that IAC part number onthe GM parts sites though .
that is the one that is listed. it says that its a 'Idle Air Control Valve Kit'.

I found it at www.auto-parts-for-less.com. IMO they are 2nd best next to www.gmpartsdirect.com.

when you get to the first mentioned site above, click on ''order gm parts and enter the P/N and make of your car. it will give you a few results at $65 apiece. so this part number is correct.

hope this helps.

-Josh
Reply
Old Mar 8, 2003 | 09:45 PM
  #11  
BWW's Avatar
BWW
Member
iTrader: (2)
 
Joined: Mar 2003
Posts: 107
Likes: 0
From: Detroit, MI
Could you get the # for the oil dipstick tube on a 350 tpi?
Reply
Old Mar 8, 2003 | 10:08 PM
  #12  
TimRS's Avatar
Senior Member
25 Year Member
Liked
 
Joined: Sep 2000
Posts: 699
Likes: 32
From: McDonough, GA
Car: 1991 Camaro RS
Engine: 305 TBI
Transmission: 700R4
Axle/Gears: 3.42
Josh, I have another one. How about the fuse panel door on the lower dash panel for 90-92 Camaro interiors?
Reply
Old Mar 8, 2003 | 11:24 PM
  #13  
joshp14's Avatar
Thread Starter
Supreme Member
 
Joined: Sep 2002
Posts: 1,834
Likes: 0
From: Norwalk, Iowa
Originally posted by TimRS
Josh, I have another one. How about the fuse panel door on the lower dash panel for 90-92 Camaro interiors?
Tim, The book i got was only on firebirds.....but if the fuse door panel is the same as a firebird one, then it will be the same part number.

this is the one in my 88 TA, i dont know if this is the one you want or not, but ill show a pic, and let me know if this is the one or not.

-Josh
Attached Thumbnails Firebird 6" thick parts book-fusepanel.jpg  
Reply
Old Mar 18, 2003 | 08:25 PM
  #14  
87GTA Runner's Avatar
Senior Member
 
Joined: Oct 2002
Posts: 530
Likes: 0
From: Nazareth, PA
Car: 87 GTA
Engine: L98
Transmission: 700R4
Thanks for doing such a great service Josh. Can you get me a PN for the bushings that the front turn signal lights assembly screw in to. It's just a little plastic/rubber bushing that the screw goes in to. Thanks.
Reply
Old Mar 18, 2003 | 08:45 PM
  #15  
joshp14's Avatar
Thread Starter
Supreme Member
 
Joined: Sep 2002
Posts: 1,834
Likes: 0
From: Norwalk, Iowa
Originally posted by 87GTA Runner
Thanks for doing such a great service Josh. Can you get me a PN for the bushings that the front turn signal lights assembly screw in to. It's just a little plastic/rubber bushing that the screw goes in to. Thanks.
3999700 - Nut, Park and signal lamp

$2.14 - www.GMpartsdirect.com + s/h
$3.21 - www.auto-parts-for-less.com + s/h


-Josh
Reply
Old Mar 23, 2003 | 12:52 PM
  #16  
1fasZ's Avatar
Junior Member
 
Joined: Apr 2001
Posts: 35
Likes: 0
From: Birmingham,AL
Complicated P/N

Josh, can you get me a part number on front and back ujoint that will fit an aluminum driveshaft that came out of an 871le transam and is going in a 84 transam with a 10 bolt rear and a t5 tranny?:hail:
Reply
Old Mar 23, 2003 | 04:24 PM
  #17  
89_305TransAm's Avatar
Member
 
Joined: Jun 2002
Posts: 191
Likes: 0
From: New Jersey
Car: '89 Firebird Trans Am WS6
Engine: 305 TBI (L03)
Transmission: 700r4
hey could you tell me the part number for for the fog lights on a 89 trans am?

Also the fuse panel door on the same year car?:d

Thanks a ton!:hail: :hail:
Reply
Old Mar 24, 2003 | 03:54 AM
  #18  
12 Sec GTA's Avatar
Senior Member
 
Joined: Jan 2002
Posts: 600
Likes: 0
From: orlando
Car: 98 Camaro SS
Engine: LS1
Transmission: M6
87 - fuse hold cover (like the pic you posted)
87- 350 TPI oil dipstick tube

Thanks.
Reply
Old Mar 24, 2003 | 05:43 AM
  #19  
novass's Avatar
TGO Supporter
iTrader: (1)
 
Joined: Nov 2002
Posts: 1,132
Likes: 1
From: Grand Island, NY
Car: 1990 Formula
Engine: 305 TPI
Transmission: WC T5
Josh, How about underhood insulation for a 90 formula firebird.

Thanks
Reply
Old Mar 24, 2003 | 07:01 AM
  #20  
NJITIROC's Avatar
Senior Member
iTrader: (2)
 
Joined: Jun 2002
Posts: 842
Likes: 1
From: Bergen County, NJ
Car: 1989 IROC-Z
Engine: L98
Transmission: T-56
where can i get a book like that for 3rd gen Camaros?
Reply
Old Mar 24, 2003 | 12:48 PM
  #21  
joshp14's Avatar
Thread Starter
Supreme Member
 
Joined: Sep 2002
Posts: 1,834
Likes: 0
From: Norwalk, Iowa
1) '87 350 TPI Dipstick tube - 14101124
2) Fuse Panel cover (pictured above) - 10019617 (discontinued)
3) 89 TA foglights - Lens - 16502945, Housing - 16503526, if you need any screws, retainers, brackets, clips, washers, or whatever else you need for it let me know.
4) '90 Formula hood insulation - 14099508
5)And for the U-Joint, all i could find is the U-joint for the 88 JG1 TA, i couldnt find the 87 w/a JG1 option.

NJITIROC - I picked mine up on ebay for $30, it came straight off of the shelf of a bankrupt Pontiac dealership. I have seen a few brand new ones on ebay as well, but they went for a little bit more money and didn't come with a fancy thick metal binder.

-Josh
Reply
Old Mar 24, 2003 | 02:21 PM
  #22  
FIII's Avatar
Junior Member
iTrader: (1)
 
Joined: Jun 2002
Posts: 46
Likes: 0
From: Vermont
Car: 88 Formula
joshp14,

Any idea on part number/name for the air deflector/spoiler thing on the front of this firebird? It just before the front tire on the bottom. I can't find it anywhere and I need a new one for my 88 Formula. This is not my car BTW, it's justins86bird's car. It was the best picture in the Reader's Rides I could find. Thanks.
Rick
Reply
Old Mar 24, 2003 | 03:22 PM
  #23  
joshp14's Avatar
Thread Starter
Supreme Member
 
Joined: Sep 2002
Posts: 1,834
Likes: 0
From: Norwalk, Iowa
Originally posted by FIII
joshp14,

Any idea on part number/name for the air deflector/spoiler thing on the front of this firebird? It just before the front tire on the bottom. I can't find it anywhere and I need a new one for my 88 Formula. This is not my car BTW, it's justins86bird's car. It was the best picture in the Reader's Rides I could find. Thanks.
Rick
If your car has the RPO W62 (aero package) and i assume it does being it's a formula, then you need p/n 10118484. Keep in mind that this is the part that i have circled below. There is also another piece that mounts in the same relative location that is maybe only 24 inches wide. let me know if the one below is the right piece or not.

It lists for 21.60 at www.auto-parts-for-less.com and it doesnt show up at gmpartsdirect.com
Reply
Old Mar 24, 2003 | 03:23 PM
  #24  
joshp14's Avatar
Thread Starter
Supreme Member
 
Joined: Sep 2002
Posts: 1,834
Likes: 0
From: Norwalk, Iowa
here is the pic...
Attached Thumbnails Firebird 6" thick parts book-poop.jpg  
Reply
Old Mar 24, 2003 | 03:29 PM
  #25  
omnipotentgoku's Avatar
TGO Supporter
iTrader: (1)
 
Joined: May 2002
Posts: 2,480
Likes: 2
From: El Paso, Texas
Car: 1987 IROC Z
Engine: 350 TPI L98 block
Transmission: 700R4
Its an Air Dam
Reply
Old Mar 24, 2003 | 03:34 PM
  #26  
joshp14's Avatar
Thread Starter
Supreme Member
 
Joined: Sep 2002
Posts: 1,834
Likes: 0
From: Norwalk, Iowa
GM calls it an 'Air deflector'.
Reply
Old Mar 24, 2003 | 03:49 PM
  #27  
FIII's Avatar
Junior Member
iTrader: (1)
 
Joined: Jun 2002
Posts: 46
Likes: 0
From: Vermont
Car: 88 Formula
Joshp14,

I don't have the aeropackage (mine looks like the car in the pic), but you did point me in the right direction and I found most of the part I needed in about 30 seconds. Thanks for helping me out!

Rick
Reply
Old Mar 24, 2003 | 04:11 PM
  #28  
83crossfireZ28's Avatar
Member
 
Joined: Dec 2002
Posts: 195
Likes: 0
Originally posted by NJITIROC
where can i get a book like that for 3rd gen Camaros?
we have like 10,000 shop manuals and parts books in a semi trailer... gm, ford, dodge.... cars, trucks... bla bla bla... we dont sell our parts books tho
Reply
Old Mar 24, 2003 | 04:12 PM
  #29  
joshp14's Avatar
Thread Starter
Supreme Member
 
Joined: Sep 2002
Posts: 1,834
Likes: 0
From: Norwalk, Iowa
Originally posted by 83crossfireZ28
we have like 10,000 shop manuals and parts books in a semi trailer... gm, ford, dodge.... cars, trucks... bla bla bla... we dont sell our parts books tho
well that doesnt do anyone any good if they just sit in there....
Reply
Old Mar 26, 2003 | 08:01 PM
  #30  
87GTA Runner's Avatar
Senior Member
 
Joined: Oct 2002
Posts: 530
Likes: 0
From: Nazareth, PA
Car: 87 GTA
Engine: L98
Transmission: 700R4
Hey Josh. I received my parts today from the first question I asked you. Perfect!!!! Thanks a million. Well, I got another one. How about the four bolts/screws for the radiator shroud on top. 87 GTA. Thanks again in advance.
Reply
Old Mar 26, 2003 | 08:41 PM
  #31  
joshp14's Avatar
Thread Starter
Supreme Member
 
Joined: Sep 2002
Posts: 1,834
Likes: 0
From: Norwalk, Iowa
Originally posted by 87GTA Runner
Hey Josh. I received my parts today from the first question I asked you. Perfect!!!! Thanks a million. Well, I got another one. How about the four bolts/screws for the radiator shroud on top. 87 GTA. Thanks again in advance.
I need a little clarification here first...What do the screws actually hold in place...the shroud? does it bolt to the radiator mount? Is it 4 screws accross the top? Also, is your car an LB9 or L98?
Reply
Old Mar 27, 2003 | 03:14 PM
  #32  
87GTA Runner's Avatar
Senior Member
 
Joined: Oct 2002
Posts: 530
Likes: 0
From: Nazareth, PA
Car: 87 GTA
Engine: L98
Transmission: 700R4
The four across the top I circled in the picture. I hope this helps. L98.
Attached Thumbnails Firebird 6" thick parts book-hood.jpg  
Reply
Old Mar 27, 2003 | 04:24 PM
  #33  
91DropTopTA's Avatar
Member
 
Joined: Dec 2000
Posts: 360
Likes: 0
From: Alexandria, LA
Car: 91 Trans Am Convertible
Engine: 300 HP 350 CI
Transmission: 700R4
Axle/Gears: Drums?
Ok, here's a couple. I need numbers for the plastic contact switches for the horn that are inside the airbag assembly on a 91 TA. I also need numbers for the bolts that attach the runners to the plenum on the TPI system.
Reply
Old Mar 27, 2003 | 06:25 PM
  #34  
joshp14's Avatar
Thread Starter
Supreme Member
 
Joined: Sep 2002
Posts: 1,834
Likes: 0
From: Norwalk, Iowa
87GTA Runner - Bolt for upper radiator mount - 11516594


91DropTopTA - Plastic Contact switch w/wire - 17989608, there are 3 different size bolts that are used when attaching the runners to the plenum/manifold. My book doesn't say where exactly they go...but i will give you EXACTLY what my book says for the description of each bolt:

14081016 (PAN HD, TORX, M8x1.25x39.5)
14081017 (TORX, 8x1.25x54)
14081014 (M8x1.25x30)

i also have a question for you 91droptopta, how many bolts TOTAL hold the runners to the engine..both sides together, and this includes to the manifold?
Reply
Old Mar 27, 2003 | 10:16 PM
  #35  
87PontiacBeast's Avatar
Member
 
Joined: Sep 2002
Posts: 390
Likes: 0
From: hazlet NJ
Car: 92 firebird
Engine: 305 tbi
Transmission: t-5
i need the pn for the gfx on the bottom of the doors of a 92 f-bird.(car in pic is not my car)
Reply
Old Mar 27, 2003 | 10:36 PM
  #36  
joshp14's Avatar
Thread Starter
Supreme Member
 
Joined: Sep 2002
Posts: 1,834
Likes: 0
From: Norwalk, Iowa
Right - 12503276
Left - 12503277
Reply
Old Apr 6, 2003 | 09:35 PM
  #37  
87GTA Runner's Avatar
Senior Member
 
Joined: Oct 2002
Posts: 530
Likes: 0
From: Nazareth, PA
Car: 87 GTA
Engine: L98
Transmission: 700R4
Hey Josh, me again. How about hood insulation and window weatherstripping, both sides, for 87 GTA. The weatherstripping is the ones that go on the door opening up to and around the windows, not the ones actually that mount on the doors. Thanks again Josh.
Reply
Old Apr 6, 2003 | 11:12 PM
  #38  
joshp14's Avatar
Thread Starter
Supreme Member
 
Joined: Sep 2002
Posts: 1,834
Likes: 0
From: Norwalk, Iowa
Originally posted by 87GTA Runner
Hey Josh, me again. How about hood insulation and window weatherstripping, both sides, for 87 GTA. The weatherstripping is the ones that go on the door opening up to and around the windows, not the ones actually that mount on the doors. Thanks again Josh.
Hood Insulation - 14099508
Hood Insulation Clips (just in case) - 3977775
RH Upper Door WS - 20606242
LH Upper Door WS - 20606243
Reply
Old Apr 7, 2003 | 02:00 PM
  #39  
underdave's Avatar
Member
20 Year Member
 
Joined: Mar 2002
Posts: 349
Likes: 7
From: KS
Car: '91 Firebird vert
Engine: 305 TBI
Transmission: auto
got one for you josh:

3rd brake light for a '92 firebird convertible (same as '91/92 bird and T/A verts..........also same as IROCs). it's built into the spoiler on the decklid. here's a pic

also the right spoiler piece for the same car. the spoiler is actually 3 pieces, and all i need is the passenger side piece (or if they come together, that's fine).

thanks bro
Attached Thumbnails Firebird 6" thick parts book-bird7.jpg  
Reply
Old Apr 7, 2003 | 02:18 PM
  #40  
joshp14's Avatar
Thread Starter
Supreme Member
 
Joined: Sep 2002
Posts: 1,834
Likes: 0
From: Norwalk, Iowa
.

Last edited by joshp14; Apr 7, 2003 at 02:31 PM.
Reply
Old Apr 7, 2003 | 02:40 PM
  #41  
joshp14's Avatar
Thread Starter
Supreme Member
 
Joined: Sep 2002
Posts: 1,834
Likes: 0
From: Norwalk, Iowa
brake light - 919872 - $120.00 f/ www.auto-parts-for-less.com
RH Molding - 12510812 (discontinued)
Reply
Old Apr 7, 2003 | 03:44 PM
  #42  
87LTcamaro's Avatar
Member
 
Joined: Jan 2003
Posts: 198
Likes: 1
From: Sherman, TX
josh you rock

hey josh, i wish you had one for camaros. but anyway i just wanted to say thats its great to see ppl helping eachother.....all i ever see on the net is ppl screwin eachother....so good job and keep helping ppl! you rock dude.
-Ryan-
Reply
Old Apr 8, 2003 | 06:39 PM
  #43  
TimRS's Avatar
Senior Member
25 Year Member
Liked
 
Joined: Sep 2000
Posts: 699
Likes: 32
From: McDonough, GA
Car: 1991 Camaro RS
Engine: 305 TBI
Transmission: 700R4
Axle/Gears: 3.42
Josh, can you get the part number for the spring that goes with latch on the console lid?
Reply
Old Apr 8, 2003 | 09:54 PM
  #44  
joshp14's Avatar
Thread Starter
Supreme Member
 
Joined: Sep 2002
Posts: 1,834
Likes: 0
From: Norwalk, Iowa
Originally posted by TimRS
Josh, can you get the part number for the spring that goes with latch on the console lid?
1985-1992 firebird console spring - 10036765
Reply
Old Apr 8, 2003 | 10:09 PM
  #45  
TimRS's Avatar
Senior Member
25 Year Member
Liked
 
Joined: Sep 2000
Posts: 699
Likes: 32
From: McDonough, GA
Car: 1991 Camaro RS
Engine: 305 TBI
Transmission: 700R4
Axle/Gears: 3.42
Josh you are the man.:hail: :hail:
Reply
Old Apr 10, 2003 | 07:17 PM
  #46  
87GTA Runner's Avatar
Senior Member
 
Joined: Oct 2002
Posts: 530
Likes: 0
From: Nazareth, PA
Car: 87 GTA
Engine: L98
Transmission: 700R4
Hi Josh. I'm going to pick up my weather strips and hood insulation tomorrow. I'm glad you remembered about the clips, because I didn't. I'm getting them , too. Thanks a bunch. Well, I've got another one. How about a radio pod for an 87. This might be a tough one.
Reply
Old Apr 10, 2003 | 07:32 PM
  #47  
joshp14's Avatar
Thread Starter
Supreme Member
 
Joined: Sep 2002
Posts: 1,834
Likes: 0
From: Norwalk, Iowa
If this is what you are talking about, then the number is 10125293. The vents in the side, and the bracket inside the top come with this pod too. Keep in mind that it doesnt come with the radio trim plate.
Attached Thumbnails Firebird 6" thick parts book-dsc00130-1.jpg  
Reply
Old Apr 10, 2003 | 07:39 PM
  #48  
87GTA Runner's Avatar
Senior Member
 
Joined: Oct 2002
Posts: 530
Likes: 0
From: Nazareth, PA
Car: 87 GTA
Engine: L98
Transmission: 700R4
That's it buddy. You came through again. Nice gauges BTW. I also notice you have the rare badge signifying a premium sound system. Do you know if you can get them anywhere. I'm putting in a killer system and it would be a nice little touch.
Reply
Old Apr 10, 2003 | 07:44 PM
  #49  
joshp14's Avatar
Thread Starter
Supreme Member
 
Joined: Sep 2002
Posts: 1,834
Likes: 0
From: Norwalk, Iowa
not sure man. i have the p/n for the little 'performace sound' badge, and that is 10041405, but im not sure if its discontinued or not. On mine it looks like it's riveted or the prongs are melted into the back of the trim plate. only other place you could try is ebay or a boneyard.
Reply
Old Apr 12, 2003 | 05:16 AM
  #50  
LIDNR2's Avatar
Junior Member
20 Year Member
 
Joined: Apr 2003
Posts: 78
Likes: 0
From: N.E. Pennsylvania
Car: '89 Formula 350, T-Top
Engine: L98
Transmission: 700r4
Axle/Gears: Stock 3.73's
89 WS6 wheel centers

Hi Josh, Jim here, would you be able to tell me the number for a 1989 Formula 350 w/ WS6 silver wheel center cap. I lost one with the black WS6 logo on it and can't find it any where. My car only has 16,000 miles on it. thanks in advance.
Reply



All times are GMT -5. The time now is 02:47 PM.