window sweeps problem
#1
Junior Member
Thread Starter
Join Date: Oct 2008
Location: GA
Posts: 6
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1989 RS Camaro
Engine: 305
window sweeps problem
I just replaced the window sweeps on the driver side of 89 camaro. After everything was put back together and the window was rolled back up I noticed that it does not seal evenly and there are gaps that will let water go down into the door. Sweeps were purchaced from Classic Industries, the pack said the restorers choice part #2064. Does anyone have a fix for this.
#2
Senior Member
iTrader: (1)
Join Date: Oct 2008
Location: Western Washington
Posts: 644
Likes: 0
Received 0 Likes
on
0 Posts
Car: 86 T/A
Engine: 5.0 TPI
Transmission: 700R4
Re: window sweeps problem
Have you put the interior trim panel back on yet? That may press the glass out a little more. Is the window adjusted properly? I don't know if there is a fix for your problem, but perhaps it's not as big a problem as you think. Doors have drains in the bottom to let any water out that gets in.
#3
Supreme Member
iTrader: (3)
Join Date: May 2004
Location: Kingsport Tenn
Posts: 1,036
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1992 camaro
Engine: LT1
Transmission: 4L60E
Axle/Gears: 3:73
Re: window sweeps problem
As said above you will have to re-adjust the window I took a water hoes to mine.I seen the leak then re-adjusted ,water..... finally I got it to seal againit will take a little time to get it back to perfect.
#4
Junior Member
Join Date: May 2006
Location: Bedford, VA
Posts: 78
Likes: 0
Received 0 Likes
on
0 Posts
Car: 83 Camaro
Engine: LT1 SD Mode 30lb/hr
Transmission: T56
Axle/Gears: 3.23
Re: window sweeps problem
I too bought the Classic Industries window sweeps and am seeing the same problem.
For the life of me I cannot get them to seal against the window.
For the life of me I cannot get them to seal against the window.
#7
Supreme Member
iTrader: (4)
Join Date: Mar 2009
Location: Pepperell, MA
Posts: 3,079
Likes: 0
Received 3 Likes
on
3 Posts
Car: 1987 Trans Am
Engine: LQ9/L92
Transmission: 4L60E
Re: window sweeps problem
if the window's been adjusted and you're still having issues, check the bolt spacing on the door. i have seen some cases where they are not uniform to mount the outer seal (think friday at 4:59pm at the assembly plant - gotta hurry it up so i can go home!). when this happens, the bolts can pull the sweep a little bit and bunch it up. if that is the case, just enlarge the holes a little and it should fit more flat
Trending Topics
#8
Junior Member
Join Date: May 2006
Location: Bedford, VA
Posts: 78
Likes: 0
Received 0 Likes
on
0 Posts
Car: 83 Camaro
Engine: LT1 SD Mode 30lb/hr
Transmission: T56
Axle/Gears: 3.23
Re: window sweeps problem
Seeing how I have revived a three year old thread. I'm going to start a new one to see if anyone else has had the same problem with the Classic Industries seals.
For 1ADan: The seal is not bunched. I acctually had to drill 2 holes in the seal to align two of the mounting bolts. It is laying flat and looks good untill you shut the door and then you see the gap. Its like I have to choose the leak to be at the cab and window or a the window sweep and window. If I push the window out far enough to close the window sweep gap it no longer seals tight at the top of the car.
For 1ADan: The seal is not bunched. I acctually had to drill 2 holes in the seal to align two of the mounting bolts. It is laying flat and looks good untill you shut the door and then you see the gap. Its like I have to choose the leak to be at the cab and window or a the window sweep and window. If I push the window out far enough to close the window sweep gap it no longer seals tight at the top of the car.
Thread
Thread Starter
Forum
Replies
Last Post
1992 Trans Am
History / Originality
27
05-10-2023 07:19 PM
IROCZDAVE (88-L98)
Interior Parts for Sale
4
10-06-2016 09:08 AM
ambainb
Camaros for Sale
11
04-25-2016 09:21 PM
IROCZDAVE (88-L98)
Interior Parts for Sale
0
08-06-2015 03:51 PM