Amp wiring question
#1
Member
Thread Starter
Join Date: Dec 2002
Location: Washington, Seattle
Posts: 203
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1992 Camaro RS
Engine: 3.1 MPFI
Transmission: 700R4
Amp wiring question
ok so i have 2 4-ohm subs and i have a amp that is stable down to 1 ohm.........what i was wondering was what is the best way to wire it so i get the most watts to my subs. i dont really know anything about parallel and series so if u can like draw a pic or descibe to me thad be most great. Thanks!!
#2
TGO Supporter
Join Date: Jul 1999
Location: Another world, some other time
Posts: 3,838
Likes: 0
Received 4 Likes
on
4 Posts
Car: 86 LG4 & 92 TBI Firebird
Engine: The Mighty 305!
Transmission: 700R4
Axle/Gears: 3.42
The lowest ohms you can get with two 4 ohm subs is 2 ohms. Wire both + terminals on the subs to + on the amp. Then wire both - terminals on the subs to the - on the amp. That will give you a parallel cct.
#3
Member
Thread Starter
Join Date: Dec 2002
Location: Washington, Seattle
Posts: 203
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1992 Camaro RS
Engine: 3.1 MPFI
Transmission: 700R4
do you mean like have the 2 + wires combine before it gets to my amp or connect them to my amp seperatly?
#6
Member
Join Date: Aug 2003
Location: Bakersfield
Posts: 466
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 IROC-Z
Engine: 1989 350 4 bolt roller block
Transmission: ProBuilt 700R4 Road Race with Edge 9.5" 2800 stall lockup converter
"Tab A" is positive wire (+) connection on speaker 1. Run a wire from the positive (+) on speaker 1 to the positive (+) on speaker 2. Run a wire from Speaker 2 positive (+) to To "Slot A" which is the Amp positive (+).
"Tab B" is negative wire (-) connection on speaker 1. Run a wire from the negative (-) on speaker 1 to the negative (-) on speaker 2. Run a wire from Speaker 2 negative (-) to To "Slot B" which is the Amp negative (-).
Does this work for you? I could draw you an actual picture but I have no place to post the drawing, sorry.....
Speaker 1+---------->Speaker 2+----------->Amp positive terminal
Speaker 1- ---------->Speaker 2- ----------->Amp negative terminal
"Tab B" is negative wire (-) connection on speaker 1. Run a wire from the negative (-) on speaker 1 to the negative (-) on speaker 2. Run a wire from Speaker 2 negative (-) to To "Slot B" which is the Amp negative (-).
Does this work for you? I could draw you an actual picture but I have no place to post the drawing, sorry.....
Speaker 1+---------->Speaker 2+----------->Amp positive terminal
Speaker 1- ---------->Speaker 2- ----------->Amp negative terminal
#7
Member
Thread Starter
Join Date: Dec 2002
Location: Washington, Seattle
Posts: 203
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1992 Camaro RS
Engine: 3.1 MPFI
Transmission: 700R4
so i actually should splice the 2 +'s and -'s before they get to the amp so there is acutally only 2 direct imputs going to the amp instead of 4? will that make it 2 ohms? is 4 imputs 4 ohms or 8? thanks a ton guys!!
Trending Topics
#9
Senior Member
Join Date: Jan 2000
Location: Ft. Lauderdale, FL
Posts: 528
Likes: 0
Received 0 Likes
on
0 Posts
Thread
Thread Starter
Forum
Replies
Last Post
db057
TBI
10
08-11-2015 10:11 PM