kicker l7
#3
Re: kicker l7
sure there is enough room to physically fit them there in the well, but the sub requirements call for too much air space to sound good. The available air space in the well is barely enough for a sealed box. The L7s sound way better ported, but that needs almost twice the space as a sealed box.
#4
Supreme Member
iTrader: (2)
Join Date: May 2002
Location: Everett, WA
Posts: 4,449
Likes: 0
Received 7 Likes
on
7 Posts
Car: 87' IROC
Engine: L98
Transmission: T56
Re: kicker l7
A single L7 15 calls for a minimum of 1.5 cu ft for sealed and 3.0 cu ft for ported. 3.0 is probably a little big for a thirdgen, especially after the port. Why anyone needs a 15 inside a thirdgen is beyond me anyways.
#6
Junior Member
Join Date: Dec 2009
Location: Ohio
Posts: 80
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1988 Camaro IROC-Z and 91 Z28
Engine: 305 TPI and 350 TPI
Transmission: 700r4
Axle/Gears: unsure of ratio but POSI (:
Re: kicker l7
i have 2 15 hx2s in my 91 z and they sound awesome im bout to have a box built for my subs and ported tuned to 30 hertz (: just something you gotta love lol
Trending Topics
#8
Supreme Member
iTrader: (8)
Join Date: Jul 2001
Location: New Boston, IL, USA
Posts: 3,204
Likes: 0
Received 6 Likes
on
6 Posts
Car: '90 Formula 350
Engine: 383 SBC
Transmission: ProBuilt S/S 700-R4 & ACT 9" Stall
Axle/Gears: 10 bolt 3.23
Re: kicker l7
I'm running 2 18"s sealed and there around 3.0 cubic or so each (seperated chambers of course). I cut out most of the plastic pieces though.
To get an L7 15" to fit you'll probably have to mount it off to one side because I doubt you'll have enough room with the pulldown motor. You could always find the specs and make a mock-up piece from cardboard that'll give you a better idea on sub placement.
To get an L7 15" to fit you'll probably have to mount it off to one side because I doubt you'll have enough room with the pulldown motor. You could always find the specs and make a mock-up piece from cardboard that'll give you a better idea on sub placement.
#9
Supreme Member
iTrader: (2)
Join Date: May 2002
Location: Everett, WA
Posts: 4,449
Likes: 0
Received 7 Likes
on
7 Posts
Car: 87' IROC
Engine: L98
Transmission: T56
Re: kicker l7
I'm running 2 18"s sealed and there around 3.0 cubic or so each (seperated chambers of course). I cut out most of the plastic pieces though.
To get an L7 15" to fit you'll probably have to mount it off to one side because I doubt you'll have enough room with the pulldown motor. You could always find the specs and make a mock-up piece from cardboard that'll give you a better idea on sub placement.
To get an L7 15" to fit you'll probably have to mount it off to one side because I doubt you'll have enough room with the pulldown motor. You could always find the specs and make a mock-up piece from cardboard that'll give you a better idea on sub placement.
#10
Supreme Member
iTrader: (8)
Join Date: Jul 2001
Location: New Boston, IL, USA
Posts: 3,204
Likes: 0
Received 6 Likes
on
6 Posts
Car: '90 Formula 350
Engine: 383 SBC
Transmission: ProBuilt S/S 700-R4 & ACT 9" Stall
Axle/Gears: 10 bolt 3.23
Re: kicker l7
It's purely a street pounding toy car. I found the subs and stuff super cheap on eBay. One of my friends was using a ported 12" W7 in his Monte Carlo. I was just looking for something no one back home had or even thought of yet. One of the local shops told me there was no way to get 18"s to fit and even if I did it would rip the hinges on the hatch. The first shop I had build the box was horrible so I decided I might as well give it a try myself. Like anything I do I always seem to go over board.... At least I can hear something more than the "budget 383" motor screaming through 4" exhaust and race muffler.
#11
Supreme Member
iTrader: (2)
Join Date: May 2002
Location: Everett, WA
Posts: 4,449
Likes: 0
Received 7 Likes
on
7 Posts
Car: 87' IROC
Engine: L98
Transmission: T56
Re: kicker l7
It's purely a street pounding toy car. I found the subs and stuff super cheap on eBay. One of my friends was using a ported 12" W7 in his Monte Carlo. I was just looking for something no one back home had or even thought of yet. One of the local shops told me there was no way to get 18"s to fit and even if I did it would rip the hinges on the hatch. The first shop I had build the box was horrible so I decided I might as well give it a try myself. Like anything I do I always seem to go over board.... At least I can hear something more than the "budget 383" motor screaming through 4" exhaust and race muffler.
#12
Junior Member
Join Date: Dec 2009
Location: Ohio
Posts: 80
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1988 Camaro IROC-Z and 91 Z28
Engine: 305 TPI and 350 TPI
Transmission: 700r4
Axle/Gears: unsure of ratio but POSI (:
#13
Member
Join Date: Mar 2010
Location: charlotte
Posts: 284
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 Camaro
Transmission: T5
Axle/Gears: 411
Re: kicker l7
If You Need A Ported Box For L7 Kickers On Your Third Gen, You Can Get Them On eBay, They Work A Lot Better Than The Sealed Ones Because There's Not Enough Space To have Two Of Them Hitting As It Is And With No Air Flow To Them You have To Make Them Work A Lot Harder & They Blow Out So If Anyone Plans On have More Than 1 L7 I Would Reccomend The Ported Box You Can Buy On eBay, Or Get 1 12" JL Audio W7 In A Sealed Box And You'll Be Hitting A Lot Harder Than 2 L7's In A Ported Box.
Thread
Thread Starter
Forum
Replies
Last Post
Joey
Car Audio
10
06-05-2001 01:35 PM