Convertible Top Fitment Examples
#1
Junior Member
Thread Starter
iTrader: (6)
Join Date: Feb 2008
Location: Florida
Posts: 87
Likes: 0
Received 4 Likes
on
4 Posts
Car: 1989 Chevorolet Iroc-z convertible
Engine: 383, holley terminator efi
Transmission: T-56
Axle/Gears: stock 10 bolt w/ 3.73
Convertible Top Fitment Examples
I am looking to get a new top installed on my 1989 Camaro. I am wondering about the fitment of my top compared to others. I have attached photos below of the B pillar bow width and of how the top sits near the B pillar. Measuring my top along the B pillar Bow as the diagram on topsonline states it comes in at 51 3/4" wide, but the top does make a sharp angle down where the B pillar is. Just in front of the B pillar bow the top measures 51 1/4", which makes me think I need a 51" wide top. My window just barely clears/touches the top when I open and close the door so I think the 52" wide top would be to wide. I also called topsonline and he believes a 51" top would be the one to go with but before I drop $700 for a new top I want to make sure I am getting the correct one.
Also, where my top is glued to the B pillar, the seam sits way back, which looks like it should be farther forward on my B pillar. Do your tops look like this where it meets the B pillar? Also has anyone replaced their top with measurements similar to mine? If so, could you point me in the right direction for what top to get?
Thanks for your help in advance. Here are some photos of my top with a measuring tape.
Also, where my top is glued to the B pillar, the seam sits way back, which looks like it should be farther forward on my B pillar. Do your tops look like this where it meets the B pillar? Also has anyone replaced their top with measurements similar to mine? If so, could you point me in the right direction for what top to get?
Thanks for your help in advance. Here are some photos of my top with a measuring tape.
#3
Senior Member
iTrader: (1)
Join Date: Jan 2008
Location: Destin, Florida
Posts: 618
Likes: 0
Received 11 Likes
on
11 Posts
Car: 91 Trans Am Convertible
Engine: LB9 5.0 TPI
Transmission: 5 SPD
Axle/Gears: Posi Rear
Re: Convertible Top Fitment Examples
I threw caution to the wind when I replaced my top and found, and worked with, a shop that knew what they were doing. They did an excellent job and as soon as I stopped worrying about all the potential "fit" issues, my stress level went way down. Cost me a little more but I got the satisfaction that the job (and fit) was right.
#4
Supreme Member
iTrader: (2)
Join Date: Jan 2005
Location: S. UTAH
Posts: 1,246
Likes: 0
Received 163 Likes
on
135 Posts
Car: 1989 IROC-Z 305 LB9 AT Convertible
Engine: LB9 305
Transmission: AT
Re: Convertible Top Fitment Examples
Me too! My '89 desperately need a new top!
How much is the top R&R labor, in Destin , Florida?
How much is the top R&R labor, in Destin , Florida?
#6
Supreme Member
iTrader: (2)
Join Date: Jan 2005
Location: S. UTAH
Posts: 1,246
Likes: 0
Received 163 Likes
on
135 Posts
Car: 1989 IROC-Z 305 LB9 AT Convertible
Engine: LB9 305
Transmission: AT
Re: Convertible Top Fitment Examples
FWIW, Someone asked the youtube guy(above) which of the two sizes , below is that exchange..
Hey bro I got an 89 camaro convertible RS and I'm tryna order that material but it says they got the 50 inch and 51.5 inch which should I get
REPLY
Hide 4 replies
MECA Upholstery Tips1 year ago
51 inchesREPLY
MECA Upholstery Tips1 year ago
Are you going to make it from scratch because it is better to buy a ready makeREPLY
@MECA Upholstery Tips I think it's a ready makeREPLY
@MECA Upholstery Tips is stay fast cloth decent thier selling it for 289REPLY
Hey bro I got an 89 camaro convertible RS and I'm tryna order that material but it says they got the 50 inch and 51.5 inch which should I get
REPLY
Hide 4 replies
MECA Upholstery Tips1 year ago
51 inchesREPLY
MECA Upholstery Tips1 year ago
Are you going to make it from scratch because it is better to buy a ready makeREPLY
Ogc Constrictors
1 year ago@MECA Upholstery Tips I think it's a ready makeREPLY
Ogc Constrictors
1 year ago@MECA Upholstery Tips is stay fast cloth decent thier selling it for 289REPLY
Last edited by mikeceli; 01-11-2022 at 10:42 PM.
#7
Senior Member
iTrader: (1)
Join Date: Jan 2008
Location: Destin, Florida
Posts: 618
Likes: 0
Received 11 Likes
on
11 Posts
Car: 91 Trans Am Convertible
Engine: LB9 5.0 TPI
Transmission: 5 SPD
Axle/Gears: Posi Rear
Re: Convertible Top Fitment Examples
I paid about $350 for labor and was very happy with the work. I paid about $100 less back in 2004 at a different shop but also was a good job. Unfortunatly the gentleman that did that one died about 10 years ago and I went looking for another installer. Found this one in Pensacola.
Trending Topics
#8
Supreme Member
iTrader: (2)
Join Date: Jan 2005
Location: S. UTAH
Posts: 1,246
Likes: 0
Received 163 Likes
on
135 Posts
Car: 1989 IROC-Z 305 LB9 AT Convertible
Engine: LB9 305
Transmission: AT
Re: Convertible Top Fitment Examples
Three hundred, fifty sounds like a great price. I don't suppose they painted the frame, at that price?
#9
Senior Member
iTrader: (1)
Join Date: Jan 2008
Location: Destin, Florida
Posts: 618
Likes: 0
Received 11 Likes
on
11 Posts
Car: 91 Trans Am Convertible
Engine: LB9 5.0 TPI
Transmission: 5 SPD
Axle/Gears: Posi Rear
Re: Convertible Top Fitment Examples
No. Strictly the installation of the material top. Also, the headliner did not need to be replaced.
Thread
Thread Starter
Forum
Replies
Last Post