Electronics Need help wiring something up? Thinking of adding an electrical component to your car? Need help troubleshooting that wiring glitch?

Anybody Mount their MSD Box inside the center console?

Thread Tools
 
Search this Thread
 
Old 02-04-2007, 05:01 PM
  #1  
Senior Member

Thread Starter
 
1 DwnCam's Avatar
 
Join Date: Mar 2002
Location: Azusa, CA
Posts: 741
Likes: 0
Received 0 Likes on 0 Posts
Car: 92 Z28 Camaro
Engine: Procharged 406.
Transmission: T-56
Axle/Gears: Moser 9" 4.11 Gears
Anybody Mount their MSD Box inside the center console?

I was thinking of mounting my MSD Digital 6 ignition box in the center console with a fan blowing air on it. Has anybody done this? From the looks of it I'm going to have to notch the plastic to get the box to fit properly. Any pictures would be appreciated.
Old 02-05-2007, 05:52 PM
  #2  
Senior Member

Thread Starter
 
1 DwnCam's Avatar
 
Join Date: Mar 2002
Location: Azusa, CA
Posts: 741
Likes: 0
Received 0 Likes on 0 Posts
Car: 92 Z28 Camaro
Engine: Procharged 406.
Transmission: T-56
Axle/Gears: Moser 9" 4.11 Gears
Anybody?
Old 02-08-2007, 10:53 PM
  #3  
Member
 
Siggy's Avatar
 
Join Date: Feb 2005
Location: Perth WA, Australia
Posts: 112
Likes: 0
Received 0 Likes on 0 Posts
Car: 1988 Camaro IROC LB9 F
Engine: 305 HO EFI
Transmission: TH700R4
Axle/Gears: GU5 LS 3.23
No never have...just wonder why. I looked at your photos and can understand you want a clean bay. I mounted a MSD under dash on a 29 A rod for that reason and I didn't care about the RF. Really you should keep the wiring short as possible, bear in mind that the MSD will generate a bit of RF and plastic is a poor shield.
Old 02-10-2007, 09:06 AM
  #4  
Member

iTrader: (2)
 
likeenz24's Avatar
 
Join Date: Jan 2005
Location: Columbus, In
Posts: 396
Received 0 Likes on 0 Posts
Car: 87 Camaro
Engine: 406
Transmission: T56
Axle/Gears: 9" ford 35 spline axles
I mounted mine on the old ecm bracket under the dash
Old 02-11-2007, 11:13 AM
  #5  
Member

iTrader: (1)
 
Cornholio7979's Avatar
 
Join Date: Apr 2005
Location: Vegas
Posts: 208
Likes: 0
Received 1 Like on 1 Post
Car: 89 Formula, 89 IROC
Engine: GMPP 350 HO, L98
Transmission: 4l60x2
Axle/Gears: not enough, good enough
Put mine inside the fender next to the battery. You can't see the box at all, and the wiring runs along side to battery wires, so you can't see that either.
Old 02-11-2007, 05:54 PM
  #6  
Senior Member

Thread Starter
 
1 DwnCam's Avatar
 
Join Date: Mar 2002
Location: Azusa, CA
Posts: 741
Likes: 0
Received 0 Likes on 0 Posts
Car: 92 Z28 Camaro
Engine: Procharged 406.
Transmission: T-56
Axle/Gears: Moser 9" 4.11 Gears
Originally Posted by Siggy
No never have...just wonder why. I looked at your photos and can understand you want a clean bay. I mounted a MSD under dash on a 29 A rod for that reason and I didn't care about the RF. Really you should keep the wiring short as possible, bear in mind that the MSD will generate a bit of RF and plastic is a poor shield.
Speaking of RF does solid grounds at both the box and the coil help matters at all? I'd like to keep the box cool and as free from vibration as possible.
Old 02-11-2007, 09:01 PM
  #7  
Member
 
Siggy's Avatar
 
Join Date: Feb 2005
Location: Perth WA, Australia
Posts: 112
Likes: 0
Received 0 Likes on 0 Posts
Car: 1988 Camaro IROC LB9 F
Engine: 305 HO EFI
Transmission: TH700R4
Axle/Gears: GU5 LS 3.23
Absolutely....grounding is very important, I aways ground the case direct to bat-strap chassis lug with 14 gauge. The MSD can handle a fair degree of heat and vibration...they survive Hotrods which are quite firm. Dirt, moisture are to be avoided. Keep it vertically away from a heat source, some air movement over the case is desired, a fan only if confined and no other air movement available...inside the console box without venting would only contain the heat even with a fan, if you vent the console box you would most likely allow dust-dirt to enter past the trany. My 3G has its Crane 6Hi fitted to engine bay fender (clean bay was not necessary). The under dash sounds good but I would not place it close to ECM if its still there.
My Crane box sits just in front of the heater fan on fender in this photo.
http://Coolsiggy.smugmug.com/photos/117061496-M.jpg

Last edited by Siggy; 02-11-2007 at 09:12 PM.
Old 02-14-2007, 07:17 PM
  #8  
Supreme Member

iTrader: (17)
 
nelapse's Avatar
 
Join Date: Jan 2005
Location: Mobile, AL
Posts: 2,716
Likes: 0
Received 2 Likes on 2 Posts
Car: GTA
Engine: 383 HSR
Transmission: TH-700R4
Axle/Gears: 3.42
What is "RF" You refering to "EMI" Electro magnetic interference?

Radio Interference?
Old 02-18-2007, 01:01 AM
  #9  
Member
 
Siggy's Avatar
 
Join Date: Feb 2005
Location: Perth WA, Australia
Posts: 112
Likes: 0
Received 0 Likes on 0 Posts
Car: 1988 Camaro IROC LB9 F
Engine: 305 HO EFI
Transmission: TH700R4
Axle/Gears: GU5 LS 3.23
Originally Posted by nelapse
What is "RF" You refering to "EMI" Electro magnetic interference?

Radio Interference?
Yes, Radio Freq or Radio noise normally comes with the high energy ignitions. If the car electronics work OK then your only other concern can be that expensive audio system or the neighbors tv.
Old 02-18-2007, 01:10 AM
  #10  
Junior Member
 
fast89ta's Avatar
 
Join Date: May 2005
Location: souderton,pa
Posts: 56
Likes: 0
Received 0 Likes on 0 Posts
Car: 85 Camaro Z28
Engine: 408 ci bbc
Transmission: 700r4
Axle/Gears: 10 bolt 4.11 ratio
I got mine on the dashboard right in front of the passanger, i like it there but some may not like looking at it if there cars an everyday driver.
Old 02-19-2007, 08:57 PM
  #11  
Senior Member
 
burntblues's Avatar
 
Join Date: Jul 2000
Location: Charlotte, NC
Posts: 580
Likes: 0
Received 0 Likes on 0 Posts
Car: 1989 Camaro RS
Engine: 355 mildly modified
Transmission: 700R4 fully modified
Can I see some pics of the location next to the battery? My car has AC and I just can't find a place to mount it. Or how about pics of under the dash?

Thanks, mike
Old 02-20-2007, 02:47 PM
  #12  
Junior Member
 
fast89ta's Avatar
 
Join Date: May 2005
Location: souderton,pa
Posts: 56
Likes: 0
Received 0 Likes on 0 Posts
Car: 85 Camaro Z28
Engine: 408 ci bbc
Transmission: 700r4
Axle/Gears: 10 bolt 4.11 ratio
Got a pic of mine on my cardomain, page 3. Link is in my sig.
Old 02-20-2007, 07:02 PM
  #13  
Supreme Member

iTrader: (17)
 
nelapse's Avatar
 
Join Date: Jan 2005
Location: Mobile, AL
Posts: 2,716
Likes: 0
Received 2 Likes on 2 Posts
Car: GTA
Engine: 383 HSR
Transmission: TH-700R4
Axle/Gears: 3.42
here is where I mounted my MSD box. I doubt it will get to hot, I have dual fans blowing on it



Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
1992 Trans Am
History / Originality
27
05-10-2023 07:19 PM
colton_carlson
Firebirds for Sale
7
03-08-2019 12:21 PM
9192camaro
Engine/Drivetrain/Suspension Parts for Sale
16
02-03-2019 12:21 AM
Firebird sweden
Organized Drag Racing and Autocross
3
08-16-2015 05:02 PM
midias
Tech / General Engine
3
08-15-2015 05:07 PM



Quick Reply: Anybody Mount their MSD Box inside the center console?



All times are GMT -5. The time now is 11:56 PM.