Fuse blowing at WOT
#1
Fuse blowing at WOT
I have a 1985 Berlinetta 305ci carb and when evr I go to WOT or about 3/4 throttle the "Gauge" 10 (red) Fuse blows. The insterment panal still stays on but the speedometer stays at zero. I cant find anybody that would have a solution for this.
#2
Supreme Member
iTrader: (3)
Join Date: Jul 2004
Posts: 2,989
Likes: 0
Received 5 Likes
on
4 Posts
Car: '91 Z28 convertible
Engine: TPI
Transmission: T5
Axle/Gears: 3.27 posi disc
Re: Fuse blowing at WOT
Does it happen even if the engine is not running? (with key on, of course)
If so, you could unplug the TPS and try again. Then I'd unplug the Mixture Control Solenoid, the Air Diverter Valve, the Air Select Valve and the EGR solenoid. If the fuse still blows, I'd unplug the ECM.
If fuse still blows, I'd start unplugging random things because then I wouldn't know anymore.
Lou
If so, you could unplug the TPS and try again. Then I'd unplug the Mixture Control Solenoid, the Air Diverter Valve, the Air Select Valve and the EGR solenoid. If the fuse still blows, I'd unplug the ECM.
If fuse still blows, I'd start unplugging random things because then I wouldn't know anymore.
Lou
#3
Re: Fuse blowing at WOT
I dont think that the fuse blows unless the engine is running,I have a carb with all the emission stuff tooken off so basicaly everything is unplugged...
#4
Supreme Member
iTrader: (3)
Join Date: Jul 2004
Posts: 2,989
Likes: 0
Received 5 Likes
on
4 Posts
Car: '91 Z28 convertible
Engine: TPI
Transmission: T5
Axle/Gears: 3.27 posi disc
Re: Fuse blowing at WOT
I see. Do you still have the Mixture Control Solenoid? I would unplug that one and test WOT.
I am really not 100% familiar with the CCC setup, I hope somebody chimes in with more advice.
Lou
I am really not 100% familiar with the CCC setup, I hope somebody chimes in with more advice.
Lou
#6
Supreme Member
iTrader: (3)
Join Date: Jul 2004
Posts: 2,989
Likes: 0
Received 5 Likes
on
4 Posts
Car: '91 Z28 convertible
Engine: TPI
Transmission: T5
Axle/Gears: 3.27 posi disc
Re: Fuse blowing at WOT
I see, so you don't have the ECM either? Now we're on the same page.
In that case, I'd look at the carb and try to locate any kind of switch that could be triggered by the throttle position.
Otherwise, there isn't anything I can think of that would be throttle position dependent on carbed cars.
Lou
In that case, I'd look at the carb and try to locate any kind of switch that could be triggered by the throttle position.
Otherwise, there isn't anything I can think of that would be throttle position dependent on carbed cars.
Lou
#7
Junior Member
Join Date: Jun 2006
Location: Milwaukee, WI
Posts: 91
Likes: 0
Received 1 Like
on
1 Post
Car: 1985 Berlinetta
Engine: 5.0 LG4
Transmission: 700R4
Axle/Gears: 3.08 Peg Leg
Re: Fuse blowing at WOT
It sounds more like the throttle pedal is contacting something under the dash. Maybe rubbed through a wire, shorting it out. Did you do any work under the dash?
Trending Topics
#8
Re: Fuse blowing at WOT
I havent done any work with the wires other then trying to figure out the problem but I'll check under the dash and see if any of thats is happening
#9
Member
Join Date: Mar 2005
Location: Tyndall AFB, FL
Posts: 132
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1985 Z28
Engine: 305 TPI
Transmission: 700R4
Axle/Gears: garbage 2.73
Re: Fuse blowing at WOT
Double check that youre using the correct amp fuse.....I could have swore the gauges ran on 15amp fuses.
Thread
Thread Starter
Forum
Replies
Last Post
Pac J
Tech / General Engine
3
05-17-2020 10:44 AM
Damon
Tech / General Engine
8
09-26-2015 04:29 PM