Electronics Need help wiring something up? Thinking of adding an electrical component to your car? Need help troubleshooting that wiring glitch?

Cluster goes nuts !!

Thread Tools
 
Search this Thread
 
Old 05-16-2022, 07:36 AM
  #1  
Junior Member

Thread Starter
iTrader: (1)
 
romcjr's Avatar
 
Join Date: May 2011
Location: Waller,TX.
Posts: 44
Likes: 0
Received 0 Likes on 0 Posts
Car: 1984 Z28 HO
Engine: GMPP 350 HO
Transmission: 700R4 w/TCI streetfighter kit
Axle/Gears: 3.73 28 spline Eaton posi
Cluster goes nuts !!

Hey guys , I haven't been here in a while . I am having an issue with my instrument cluster . I will say that the car has been sitting for a few months and the issue was intermittent but now is not going away . The ic acts normally until I pull the headlight switch , then the gauges seem to go dead except for the speedo . Turn the switch off and back to normal .
I am retired now and not as nimble as I used to be , so I would like to have a direction to go instead of just replacing parts until I find the right one .
Thanks for the help !!
Old 05-16-2022, 06:01 PM
  #2  
Supreme Member

iTrader: (1)
 
OrangeBird's Avatar
 
Join Date: Feb 2012
Posts: 3,713
Received 673 Likes on 480 Posts
Car: 1989 Firebird
Re: Cluster goes nuts !!

Originally Posted by romcjr
Hey guys , I haven't been here in a while . I am having an issue with my instrument cluster . I will say that the car has been sitting for a few months and the issue was intermittent but now is not going away . The ic acts normally until I pull the headlight switch , then the gauges seem to go dead except for the speedo . Turn the switch off and back to normal .
I am retired now and not as nimble as I used to be , so I would like to have a direction to go instead of just replacing parts until I find the right one .
Thanks for the help !!
You are describing the classic symptom of a bad ground, and your gauges are finding their ground path through the non illuminated dash lights when the switch is off. It could be anywhere in the ground circuit, one common place is the connectors where the gauge unit plugs into the dash can get corroded and slowly begin loosing connection. If this were mine I'd start by getting the pinout of the gauge unit connectors for your car's specific year , take the gauge unit out, and check whichever connections are supposed to be ground with a meter to see that they are, in fact, grounded.
Old 05-16-2022, 06:07 PM
  #3  
Junior Member

Thread Starter
iTrader: (1)
 
romcjr's Avatar
 
Join Date: May 2011
Location: Waller,TX.
Posts: 44
Likes: 0
Received 0 Likes on 0 Posts
Car: 1984 Z28 HO
Engine: GMPP 350 HO
Transmission: 700R4 w/TCI streetfighter kit
Axle/Gears: 3.73 28 spline Eaton posi
Re: Cluster goes nuts !!

Thanks orangebird !!! Thats helps a bunch and makes sense since the car has been sitting . I will check it out and confirm fix .
Old 05-16-2022, 06:12 PM
  #4  
Supreme Member

iTrader: (1)
 
OrangeBird's Avatar
 
Join Date: Feb 2012
Posts: 3,713
Received 673 Likes on 480 Posts
Car: 1989 Firebird
Re: Cluster goes nuts !!

Your Welcome, and I hope the bad connection is easily found
Old 05-18-2022, 11:01 PM
  #5  
Supreme Member

 
vorteciroc's Avatar
 
Join Date: Jul 2006
Location: 212 is up in this Bit@#
Posts: 2,768
Received 741 Likes on 567 Posts
Car: Resto-Mod 1987 IROC-Z Clone
Engine: Alky fed L92 Vortec Twin-Turbo 6.8L
Transmission: My own built/ design 4L80M
Axle/Gears: Custom 12 bolt (4.10:1)
Re: Cluster goes nuts !!

We will have to wait until the OP makes another Post.

For any of you who has read through this Thread, and is confused about the Speedometer operating properly.
The Speedometer is cable driven (and not Electric) thus it is not affected.
Old 06-24-2022, 05:31 PM
  #6  
Junior Member
 
Bill1992's Avatar
 
Join Date: Mar 2022
Posts: 8
Likes: 0
Received 0 Likes on 0 Posts
Re: Cluster goes nuts !!

Originally Posted by vorteciroc
We will have to wait until the OP makes another Post.

For any of you who has read through this Thread, and is confused about the Speedometer operating properly.
The Speedometer is cable driven (and not Electric) thus it is not affected.
So i have a problem where my speedo works and so does the tach (it pegs but i know thats the resistor) the voltage gauge reads correct as well but the fuel, oil press and temp gauges do not seem to be working. The oil pressure drops to 30 with the key off and pegs when on. The fuel gauge reads empty when the key is on but when you turn it off it slowly goes up to about 1/8. The temp gauge just kinda sits around 120 or so it moves a tiny bit but I don't think it ever gets more than 140 or so. So does this sound like a ground problem or something since the speedo works?
BTW it's a 92 RS V8.
Thanks.
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
danijohansen87
Electronics
1
01-15-2022 02:40 PM
Mary'sMyBaby
Interior
2
07-20-2014 09:36 PM
BrOdBaNd
Electronics
5
08-11-2008 09:06 PM
chas0218
Electronics
6
07-20-2008 10:58 PM
TSCaboose
Electronics
6
08-27-2007 01:51 PM



Quick Reply: Cluster goes nuts !!



All times are GMT -5. The time now is 03:20 PM.