[VA] F/S-ZZ383,M/RII,AFR195's,Exhuast-more
05-22-2010, 09:08 PM
#1
Junior Member
Thread Starter
iTrader: (4)
Join Date: Jul 2008
Location: VA
Posts: 9
Likes: 0
Received 0 Likes
on
0 Posts
Car: A cherry Yugo
F/S-ZZ383,M/RII,AFR195's,Exhuast-more
Up for sale is my current setup, still in the car. I have many items in this sale and will split it up if I can't sell it as one.I have decided to go with another setup so my loss and your gain.
ZZ383(SOLD)
The ZZ383 short block has about 2500 miles on it and is hardly broke in. I did a compression test about 2 years ago when I installed a different cam,heads and I believe everything was within 10% of each other. The block comes with a 4340 forged 3.800" stroke and with 64cc's, the heads yield a 9.7:1 compression. I also have a Fluidampr Ext 7-1/4" balancer installed, along with LS7 roller lifters and a comp cams d/r timing chain. More info on the block below.
http://paceperformance.com/index.asp...&ProdID=132130
AFR-195's Comp-Eliminators(SOLD)
Like I said above, I installed the heads about 2 years ago, soon after AFR first introduced them. They are in excellent condition, hardly any miles on them(maybe 500 along with the cam) The heads are part#1095's and have the 65cc chambers w/2.08/1.60 and upgraded springs#8019 for cams of up to 600" lift. These are great heads, could feel the seat of the pants difference after the install. More info below.
http://www.airflowresearch.com/index.php?cPath=24_29
MiniRamII-1204 INTAKE(SOLD)
I purchased this intake when I bought the shortblock in 2004, It has a fuel rail kit for an F-body w/adj reg. I have Ford SVT 30lbs red top injectors along with a TPIS 52mm t/b. More info below.
http://www.tpis.com/parts/view/33 http://www.tpis.com/parts/view/37
http://www.tpis.com/parts/view/41
Cam(SOLD)
Comp Cams XFI 280 with 1.6 roller rockers I/E and 3/8" studs. Below are specs of the cam.
http://www.compcams.com/Cam_Specs/Ca...?csid=209&sb=0
(SOLD)
I'm also selling my headers, which I purchased from American Coating Specialties. They are Hooker hdrs#2055, w/y-pipe and both were coated.
I'm looking to get $175.00 for them, link below, I'll sell these seperate.
http://www.summitracing.com/parts/HOK-2055-1HKR/
All of the above items are used but in great condition, although I bought the shorblock in 2004, I have only put about 2500 miles on it. The heads and cam have maybe 500 miles on them. I am going to try and sell the engine complete but if I don't have any takers, will part the above items out. I'd be willing to sell the engine from oil pan to fuel rails for $3750, which will include everything listed above minus the headers. Also included, would be all the accs brackets,pulleys,edelbrock alum w/p, new alt,p/s pump, proform v/c's and all of the sensors including the M/A sensor. If you were to replicate the above engine, you would easily spend $10,000.
Again, the engine is still in the vehicle so I'm not in any rush. If there is anyone local that's interested, I'd welcome them to come by and hear the engine run and if wanted, to do a comp check and or leak down test. Also, the engine doesn't have any leaks. I'm located 30mins south of Richmond Va,23875. If you have any questions please feel free to ask.
Also, if you like the engine but don't presently have a vehicle to put it in, look at the below link. This would be a good canidate, I'd give a discount for a group purchase.
http://forums.corvetteforum.com/othe...om-c-10-a.html
ZZ383(SOLD)
The ZZ383 short block has about 2500 miles on it and is hardly broke in. I did a compression test about 2 years ago when I installed a different cam,heads and I believe everything was within 10% of each other. The block comes with a 4340 forged 3.800" stroke and with 64cc's, the heads yield a 9.7:1 compression. I also have a Fluidampr Ext 7-1/4" balancer installed, along with LS7 roller lifters and a comp cams d/r timing chain. More info on the block below.
http://paceperformance.com/index.asp...&ProdID=132130
AFR-195's Comp-Eliminators(SOLD)
Like I said above, I installed the heads about 2 years ago, soon after AFR first introduced them. They are in excellent condition, hardly any miles on them(maybe 500 along with the cam) The heads are part#1095's and have the 65cc chambers w/2.08/1.60 and upgraded springs#8019 for cams of up to 600" lift. These are great heads, could feel the seat of the pants difference after the install. More info below.
http://www.airflowresearch.com/index.php?cPath=24_29
MiniRamII-1204 INTAKE(SOLD)
I purchased this intake when I bought the shortblock in 2004, It has a fuel rail kit for an F-body w/adj reg. I have Ford SVT 30lbs red top injectors along with a TPIS 52mm t/b. More info below.
http://www.tpis.com/parts/view/33 http://www.tpis.com/parts/view/37
http://www.tpis.com/parts/view/41
Cam(SOLD)
Comp Cams XFI 280 with 1.6 roller rockers I/E and 3/8" studs. Below are specs of the cam.
http://www.compcams.com/Cam_Specs/Ca...?csid=209&sb=0
(SOLD)
I'm also selling my headers, which I purchased from American Coating Specialties. They are Hooker hdrs#2055, w/y-pipe and both were coated.
I'm looking to get $175.00 for them, link below, I'll sell these seperate.
http://www.summitracing.com/parts/HOK-2055-1HKR/
All of the above items are used but in great condition, although I bought the shorblock in 2004, I have only put about 2500 miles on it. The heads and cam have maybe 500 miles on them. I am going to try and sell the engine complete but if I don't have any takers, will part the above items out. I'd be willing to sell the engine from oil pan to fuel rails for $3750, which will include everything listed above minus the headers. Also included, would be all the accs brackets,pulleys,edelbrock alum w/p, new alt,p/s pump, proform v/c's and all of the sensors including the M/A sensor. If you were to replicate the above engine, you would easily spend $10,000.
Again, the engine is still in the vehicle so I'm not in any rush. If there is anyone local that's interested, I'd welcome them to come by and hear the engine run and if wanted, to do a comp check and or leak down test. Also, the engine doesn't have any leaks. I'm located 30mins south of Richmond Va,23875. If you have any questions please feel free to ask.
Also, if you like the engine but don't presently have a vehicle to put it in, look at the below link. This would be a good canidate, I'd give a discount for a group purchase.
http://forums.corvetteforum.com/othe...om-c-10-a.html
Last edited by Sinister87s; 06-30-2010 at 10:28 PM.
05-23-2010, 03:53 PM
#3
Junior Member
Join Date: Oct 2009
Location: Lexington, VA
Posts: 67
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1991 Camaro Z28
Engine: Carb 5.3
Transmission: Th350
Axle/Gears: Moser 12 bolt, 4.11 gears
Re: F/S-ZZ383,M/RII,AFR195's,Exhuast-more
what you want for the longblock?
05-23-2010, 08:19 PM
#5
05-23-2010, 09:31 PM
#7
Trending Topics
05-23-2010, 09:44 PM
#9
Junior Member
Thread Starter
iTrader: (4)
Join Date: Jul 2008
Location: VA
Posts: 9
Likes: 0
Received 0 Likes
on
0 Posts
Car: A cherry Yugo
LIST!
Just to reiterate, the heads and M/R are pending, everything else is still up for sale, below is a list with some prices.
ZZ383 Shortblock-----$1400.00==about 2500 miles on block.(SOLD)
Comp Cams XFI 280 part#08-467-8-----$100.00=less than 500 miles.(SOLD)
Comp Cams R/R 1.6 I/E-7/16th studs-----$125.00
Proform valve covers-----(SOLD)
TPIS 52mm T/B w/air foil-----$100.00(SOLD)
Fluidampr Ext-balancer-7-1/4"Dia-Part#720111-----$150.00=less than 500 miles.
http://www.jegs.com/i/Fluidampr/388/720111/10002/-1
TPIS 5/16 7.2 Hardened pushrods-----$60.00
F/body
ACCEL 8.8 300+ plug wires- 2 sets-part#7065- both have less than 10 miles on them-excellent condition-----$60.00 each
F/body
Hooker Headers and Y/pipe-coated #2055-1 5/8"-----$175.00(SOLD)
F/body Random Tech Cat 3" I/O-----$60.00
ZZ383 Shortblock-----$1400.00==about 2500 miles on block.(SOLD)
Comp Cams XFI 280 part#08-467-8-----$100.00=less than 500 miles.(SOLD)
Comp Cams R/R 1.6 I/E-7/16th studs-----$125.00
Proform valve covers-----(SOLD)
TPIS 52mm T/B w/air foil-----$100.00(SOLD)
Fluidampr Ext-balancer-7-1/4"Dia-Part#720111-----$150.00=less than 500 miles.
http://www.jegs.com/i/Fluidampr/388/720111/10002/-1
TPIS 5/16 7.2 Hardened pushrods-----$60.00
F/body
ACCEL 8.8 300+ plug wires- 2 sets-part#7065- both have less than 10 miles on them-excellent condition-----$60.00 each
F/body
Hooker Headers and Y/pipe-coated #2055-1 5/8"-----$175.00(SOLD)
F/body Random Tech Cat 3" I/O-----$60.00
Last edited by Sinister87s; 06-22-2010 at 04:39 AM.
05-27-2010, 11:38 AM
#19
Junior Member
Thread Starter
iTrader: (4)
Join Date: Jul 2008
Location: VA
Posts: 9
Likes: 0
Received 0 Likes
on
0 Posts
Car: A cherry Yugo
Re: F/S-ZZ383,M/RII,AFR195's,Exhuast-more
Started wrenching yesterday and snapped a few pics, the headers have a small hole in the Y-pipe where I had an AFR gauge mounted, also took some pics of the engine valley right after I pulled the intake, it's nice and clean. And lastly, I have a pic of the 2 sets of plug wires I'm selling.
Last edited by Sinister87s; 06-30-2010 at 10:29 PM.
06-03-2010, 11:25 AM
#20
Junior Member
Thread Starter
iTrader: (4)
Join Date: Jul 2008
Location: VA
Posts: 9
Likes: 0
Received 0 Likes
on
0 Posts
Car: A cherry Yugo
Re: F/S-ZZ383,M/RII,AFR195's,Exhuast-more
Updated list, I still have the Exhaust for sale, should have some pics of the block later today.
Last edited by Sinister87s; 06-22-2010 at 04:49 AM.
06-04-2010, 12:48 AM
#21
Junior Member
Thread Starter
iTrader: (4)
Join Date: Jul 2008
Location: VA
Posts: 9
Likes: 0
Received 0 Likes
on
0 Posts
Car: A cherry Yugo
Re: F/S-ZZ383,M/RII,AFR195's,Exhuast-more
I finally got the heads off and took some pics of the block's topend. Still looks great with no surprises.
I also took a pic of the valve train parts that I also have for sale.
I also took a pic of the valve train parts that I also have for sale.
Last edited by Sinister87s; 06-30-2010 at 10:28 PM.
06-04-2010, 01:09 AM
#23
Junior Member
Thread Starter
iTrader: (4)
Join Date: Jul 2008
Location: VA
Posts: 9
Likes: 0
Received 0 Likes
on
0 Posts
Car: A cherry Yugo
Re: F/S-ZZ383,M/RII,AFR195's,Exhuast-more
Hey guys, I just wanted to add that allot of people have asked about the block and have been waiting on me to get some pics. I would prefer to sell this block local as it's just allot easier as far as having to not deal with shipping, plus you can look over the block before you buy it. So having said that, I would be more inclined to sell it local before having to make a crate and arrange shipping, so local peep's will take first priority. Although, money talks and if it takes shipping to make the sale so be it.
06-04-2010, 12:48 PM
#24
Junior Member
Thread Starter
iTrader: (4)
Join Date: Jul 2008
Location: VA
Posts: 9
Likes: 0
Received 0 Likes
on
0 Posts
Car: A cherry Yugo
Re: F/S-ZZ383,M/RII,AFR195's,Exhuast-more
Allot of folks are asking why I'm selling everything and below is the answer, I'm switching to an LS1 in my t/a, I already have the LS engine and trans awaiting it's new home once everything else is gone.
Last edited by Sinister87s; 06-05-2010 at 12:22 AM.
Since your local, or the same state, I'll throw in the CAT for free.
06-05-2010, 09:56 PM
#27
Junior Member
Join Date: Jul 2009
Posts: 37
Likes: 0
Received 0 Likes
on
0 Posts
Re: F/S-ZZ383,M/RII,AFR195's,Exhuast-more
Whats your paypal info so i can send you a payment for them. I can send you $150 now and the rest on thursday. how much were you asking for the heads
06-06-2010, 12:22 AM
#28
Junior Member
Thread Starter
iTrader: (4)
Join Date: Jul 2008
Location: VA
Posts: 9
Likes: 0
Received 0 Likes
on
0 Posts
Car: A cherry Yugo
Re: F/S-ZZ383,M/RII,AFR195's,Exhuast-more
Sorry Sox but the headers sold to another member today while I was at work, this was the person I was awaiting to hear the response from. Also, the heads were sold a few days ago on another site, again sorry I couldn't help you.
06-07-2010, 09:20 AM
#31
Junior Member
Thread Starter
iTrader: (4)
Join Date: Jul 2008
Location: VA
Posts: 9
Likes: 0
Received 0 Likes
on
0 Posts
Car: A cherry Yugo
Updated List!
Comp Cams PRO Magnum R/R, 1.6, I/E--7/16th studs-----$125.00
ARP Head Bolt--Should fit all sbc's and LT-1's-----$50.00
TPIS-hardened 5/16 7.2" pushrods-----$60.00
Fluidampr Part#720111 Ext-balancer-7-1/4"Dia-----$150.00=less than 500 miles.
http://www.jegs.com/i/Fluidampr/388/720111/10002/-1
Random Technologies-High Flow CAT--3" I/O-----$60.00
ACCEL 8.8 300+ plug wires- (2 sets) part#7065- both have less than 10 miles on them-excellent condition-----$60.00 each
http://www.summitracing.com/parts/ACC-7065/
ARP Head Bolt--Should fit all sbc's and LT-1's-----$50.00
TPIS-hardened 5/16 7.2" pushrods-----$60.00
Fluidampr Part#720111 Ext-balancer-7-1/4"Dia-----$150.00=less than 500 miles.
http://www.jegs.com/i/Fluidampr/388/720111/10002/-1
Random Technologies-High Flow CAT--3" I/O-----$60.00
ACCEL 8.8 300+ plug wires- (2 sets) part#7065- both have less than 10 miles on them-excellent condition-----$60.00 each
http://www.summitracing.com/parts/ACC-7065/
Last edited by Sinister87s; 06-22-2010 at 04:58 AM.
06-16-2010, 12:00 PM
#37
Supreme Member
iTrader: (5)
Join Date: Aug 2007
Location: Milwaukee, Wisconsin
Posts: 1,525
Likes: 0
Received 1 Like
on
1 Post
Car: 1987 IROC-Z
Engine: 383 with Edelbrock ProFlow EFI
Transmission: TH350
Axle/Gears: 12 bolt 3.73 Eaton posi
Re: F/S-ZZ383,M/RII,AFR195's,Exhuast-more
Are any of the plug wires or boots melted or burnt?
06-22-2010, 04:55 AM
#39
Junior Member
Thread Starter
iTrader: (4)
Join Date: Jul 2008
Location: VA
Posts: 9
Likes: 0
Received 0 Likes
on
0 Posts
Car: A cherry Yugo
Re: F/S-ZZ383,M/RII,AFR195's,Exhuast-more
I have updated my list in a few posts above this one, also I will have a few more performance parts that I will be listing in the near future, thanks.
Thread
Thread Starter
Forum
Replies
Last Post
89vette
Tech / General Engine
2
02-28-2001 07:04 AM
