CamMan83

Here is what I have left from my parting out. Shoot me a PM on anything you may be interested in and I will get back with you as soon as possible. Check out my interior parts as well.

Engine (15,000 miles): Asking $5500 (over $10k in it, I have all receipts)

• Supercharged 360 Small Block Chevy
o K&N Xstream Air Flow Air Filter Assembly
o Holley In-line Blue Electric Fuel Pump with Regulator and Gauge
o Edelbrock 750 CFM Performer Carburetor tuned w/ Jets, Rods, Springs and Stubstack
o B&M 144 Roots Supercharger with 10 psi pulleys
o Ported and polished heads with valve job
o Bronze valve guide inserts
o ARP Head bolts
o Comp Cams Hydraulic NX268H-13 Blower camshaft and lifters
o Comp Cams Raised Guide Plates and ARP Rocker Arm Studs
o Manley Street Master Swirl Polished Intake/Exhaust Valves
o Comp Cams dual spring oversized Valve Springs
o Comp Cams 10 degree racing locks and retainers
o Comp Cams Valve Seals
o Comp Cams Heat Treated Pushrods
o Summit Racing 1.5:1 Full Roller Rocker Arms and Lock Nuts
o Billet Double-Row Roller Timing Chain with Thrust Bearing
o Edelbrock Tubular Exhaust System and 3 inch exhaust into Flowmaster 70 Series Muffler and Welded in Cut-Out w/ Electric Valve
o MSD 6AL Ignition Box
o SBC Distributor with Hypertech 53k Volt Coil, Cap and Rotor
o MSD Extreme HEI Distributor Cap and Rotor
o MSD Distributor Advance Kit
o Crane Cams Adjustable Vacuum Advance Canister
o MSD 8.5mm Spark Plug Wires
o Autolite 2 stage cooler Spark Plugs
o Chevy 350 block bored, champherd, torque plated, align bored and surfaced
o ARP four bolt main bolts
o Chevy 350 Crankshaft Cleaned and Polished
o Chevy 350 Rods polished and ARP Wave-loc bolts
o JE Dished -24cc Forged Blower Pistons
o JE Hellfire Rings, Straight wall pins and Spiro locks
o Clevite 77 Cam, Rod and Main Bearings
o Summit High Volume oil pump with welded on pickup
o Stud kit and ARP Oil Pump Driveshaft
o Moroso 6-qt, baffled oil pan for Third Gen Camaro with one piece Fel-Pro Gasket
o Edelbrock Victor Series Water Pump
o 180 degree Thermostat
o Copper 3-core radiator and Electric cooling fan setup with relays
o Fel-Pro Gaskets throughout the whole motor
o SFI Certified Flexplate and 8 inch Steel Damper
o Whole rotating assembly balanced in and out of the motor
o Chrome Dress Up Kit
o Tuff Stuff Gear Reduction Mini Starter
o Optima Red Top Starting Battery
o B&M SuperCooler Engine Oil Cooler with Electric Fan

Suspension:

• BMR Adjustable Panhard Rod -$100

Chassis:

• Factory Steering Brace "Wonderbar" -$45

Transmission (150 miles on the rebuild: Asking $2000)

• Pro-Built TH700R-4 Transmission - $1,700
• Polyurethane Transmission Mount
• TCI 11" Breakaway Torque Converter - $300
• Summit Steel Transmission Pan

Wheels/Tires (lots of tread: Asking $600)

• 16 x 8 Polished Aluminum IROC Wheels
• Falken 245/45ZR16 Tires

ademarti

Please give me prices for these:
1) B&M 144 Roots Supercharger with 10 psi pulleys
2) Energy Suspension Polyurethane Sway Bar Bushing Kit
3) Weld-in Subframe Connectors

jas2730

iTrader: (7)

How much for the msd 6AL and 8.5mm wires shipped to 26757?

89newfun

iTrader: (3)

BMR Adjustable Panhard Rod - pm
Spohn Tubular Rear Lower Control Arms - pm
Edelbrock 3-Point Strut Tower Brace ( not the tpi unit right?)

white1991rs

how much for the 34mm sway bar?

Method_z28

price on the prop valve?

Stu's '85 IROC

iTrader: (2)

Can I see pics and a price for the lowering springs? How many miles are on them and how much does it drop the car? I'd need them shipped to Manchester NY 14504. Thanks!

88blueiroc

Can I see some pics of the wheels? Thanks

evilemokid94

iTrader: (6)

willing to sell the carb and dizzy?

UnderCover89TBI

iTrader: (25)

would also like a price on the 3 points strut tower brace. thank you.

blackjack12982

What would a shipped price on the wonderbar and SFC's to 40121 be? Most importantly the wonderbar...

irocz

where did you get all those parts to rebuild the rearend? I'd be interested if there was any way to ship.

83C_CamAroZ28

iTrader: (12)

do u still have the Proportioning Valve?

ctoledo0834

How much for the • Eibach Pro-Kit Lowering Springs and Welded in Cut-Out w/ Electric Valve and • BMR Adjustable Panhard Rod
Ship to Miami 33010

ctoledo0834

How much for the • Eibach Pro-Kit Lowering Springs and Welded in Cut-Out w/ Electric Valve and • BMR Adjustable Panhard Rod
Ship to Miami 33010

mygta87

iTrader: (4)

How much for the oil cooler with fan

syncom

items i am interested in are sbc distributor and all that comes with it. edelbrock water pump and radiator with fan system. shipped to 84528

DrewsCam

iTrader: (2)

any pictures of the subframe connectors?

rummie

Still have the 3core rad and fan setup? And how much. thanks

blackjack12982

Anybody ever hear anything from the seller?

psmith757

how much for the subframe connectors and what kind are they?

subroc

iTrader: (2)

which prop valve is it and do you still have it? Price?

fishyz

Still have the pro-kit?