Achieving better Y-Pipe Clearance
#3
Supreme Member
iTrader: (14)
Join Date: Aug 2006
Location: Central NJ
Posts: 12,652
Likes: 0
Received 46 Likes
on
44 Posts
Car: 86 Trans Am, 92 Firebird
Engine: 408 sbc, 3.1L of raw power
Transmission: TKO600, T5
Axle/Gears: Moser 9", 3:70 trutac, 3:23 torsion
Re: Achieving better Y-Pipe Clearance
poly inserts for the stock clambshell will raise the engine.
#7
Senior Member
Join Date: Jun 2008
Location: Norfolk VA
Posts: 1,298
Likes: 0
Received 2 Likes
on
2 Posts
Car: 85 Camaro IROC
Engine: 5.7 TPI
Transmission: 700-R4
Axle/Gears: open rear, 3.42 gears
Re: Achieving better Y-Pipe Clearance
ive got this same problem but with my cat
i can literally stick my forearm inbetween the the car and the pipe
ive seriously considered putting a length of 2X8 on a jack and trying to bend it up higher
is this a reasonable thing to do?
what if i had a blowtorch to heat the metal first?
i can literally stick my forearm inbetween the the car and the pipe
ive seriously considered putting a length of 2X8 on a jack and trying to bend it up higher
is this a reasonable thing to do?
what if i had a blowtorch to heat the metal first?
Trending Topics
#8
Supreme Member
iTrader: (56)
Re: Achieving better Y-Pipe Clearance
A Good muffler shop can do that for you.
this is how you would do it at Home..
get the car on Jack stands up Hi enof to get under and move.(you)
you will need a good jack.. and a thin sheet of alum
(tween pipe & car bottom) check see space..
put jack on Pipe.. run jack up till you see pipe pushing up.
start to heat pipe till red, apply a bit more force up and let cool.
check see space... is it moved up more.? repeat till done.
NOTE: pre loading the pipe with presher gives you a 2nd set of hands.
when the pipe is soft enof To MOVE..it will tweek upward from the presher. saving you the time to see if it is time to push it..
this can be done in more then one place...
this 3" cat back runs close to the bottom pan of the car.
other parts AKA lift bars sit lower.. (pips are tuck up nice and neet)
Y Pipe sitting up nice and High.. from Y cat back sits on yop of cross member up over rear.. and out. factry styl..
this is how you would do it at Home..
get the car on Jack stands up Hi enof to get under and move.(you)
you will need a good jack.. and a thin sheet of alum
(tween pipe & car bottom) check see space..
put jack on Pipe.. run jack up till you see pipe pushing up.
start to heat pipe till red, apply a bit more force up and let cool.
check see space... is it moved up more.? repeat till done.
NOTE: pre loading the pipe with presher gives you a 2nd set of hands.
when the pipe is soft enof To MOVE..it will tweek upward from the presher. saving you the time to see if it is time to push it..
this can be done in more then one place...
this 3" cat back runs close to the bottom pan of the car.
other parts AKA lift bars sit lower.. (pips are tuck up nice and neet)
Y Pipe sitting up nice and High.. from Y cat back sits on yop of cross member up over rear.. and out. factry styl..
Last edited by articwhiteZ; 01-20-2010 at 09:18 PM.
#9
Supreme Member
Re: Achieving better Y-Pipe Clearance
I modified the cross member to get a little more ground clearence.
Thread
Thread Starter
Forum
Replies
Last Post