help!!!in exhaust shop 2210 can i fit dual 3" to third member?
#1
Member
Thread Starter
iTrader: (4)
Join Date: Dec 2010
Location: Virginia
Posts: 122
Likes: 0
Received 0 Likes
on
0 Posts
Car: 88 Iroc Z
Engine: L98 350
Transmission: 700 R4
help!!!in exhaust shop 2210 can i fit dual 3" to third member?
I have a 383 procharged irocz with hooker 2210s. My originally exhaust plan was run dual 3inch lines from the collectors to under the 700r4 crossmember then connect them together with 3inch y 4"outlet. Then another y connected to that, with a dump valve and the other side going to the factory exhaust.
The installer thinks he can only fit 2.5 inch without it being a serious ground clearance issue on the drivers side coming along next to the transmission and he doesn't think I need a bigger exhaust which I believe I do especially if I raise the boost later.
Is anyone running stock height and 3inch along side the driver side without major clearance issues?
I am aware ill need to be very mindful of potholes, dips and speed bumps. But I wanna get a fellow third gener's input before I tell him to run 3inch.
Thanks ahead of time!!! and input tonight even if quick would be assume since I have to make a call in the mourning
The installer thinks he can only fit 2.5 inch without it being a serious ground clearance issue on the drivers side coming along next to the transmission and he doesn't think I need a bigger exhaust which I believe I do especially if I raise the boost later.
Is anyone running stock height and 3inch along side the driver side without major clearance issues?
I am aware ill need to be very mindful of potholes, dips and speed bumps. But I wanna get a fellow third gener's input before I tell him to run 3inch.
Thanks ahead of time!!! and input tonight even if quick would be assume since I have to make a call in the mourning
#4
Member
Thread Starter
iTrader: (4)
Join Date: Dec 2010
Location: Virginia
Posts: 122
Likes: 0
Received 0 Likes
on
0 Posts
Car: 88 Iroc Z
Engine: L98 350
Transmission: 700 R4
Re: help!!!in exhaust shop 2210 can i fit dual 3" to third member?
I've got it back they didn't keep it as tight as they could. It is so low It can scrap if I take a hard flat turn . Lb9gta was u lucky enough to have someone in the area that has oval pipe or did you have to order it
#6
Moderator
Re: help!!!in exhaust shop 2210 can i fit dual 3" to third member?
I have 2210's with 3" duals and I do not scrape. I'm lowered also. Mine ends jus before the rear end though.
#7
Member
Thread Starter
iTrader: (4)
Join Date: Dec 2010
Location: Virginia
Posts: 122
Likes: 0
Received 0 Likes
on
0 Posts
Car: 88 Iroc Z
Engine: L98 350
Transmission: 700 R4
Re: help!!!in exhaust shop 2210 can i fit dual 3" to third member?
I like the way ur exhaust is ran. That's the way I wanted to run it and the exhaust shop missed up. Hopefully the next shop will do better. Did u run oval in that section?
Trending Topics
#8
Supreme Member
#10
Senior Member
Join Date: Mar 2007
Location: Muscatine IA
Posts: 574
Likes: 0
Received 2 Likes
on
2 Posts
Car: 91 Firebird Formula
Engine: 383
Transmission: built 700r4
Axle/Gears: 4.11, 9inch
Re: help!!!in exhaust shop 2210 can i fit dual 3" to third member?
just got my heddman s tensions ill be able to tuck it up close but im not sure it will be enough. may just have to order the 2.5 vesions. its a tight fit with an aftermarket cross member
#11
Member
Thread Starter
iTrader: (4)
Join Date: Dec 2010
Location: Virginia
Posts: 122
Likes: 0
Received 0 Likes
on
0 Posts
Car: 88 Iroc Z
Engine: L98 350
Transmission: 700 R4
Re: help!!!in exhaust shop 2210 can i fit dual 3" to third member?
These are the pictures of my exhaust redone 3" to 4"Y with a dump vavle and better clearance than the last time ill post clearance pics in a lit bit
#13
Member
Thread Starter
iTrader: (4)
Join Date: Dec 2010
Location: Virginia
Posts: 122
Likes: 0
Received 0 Likes
on
0 Posts
Car: 88 Iroc Z
Engine: L98 350
Transmission: 700 R4
Re: help!!!in exhaust shop 2210 can i fit dual 3" to third member?
Here's a few clearance pics to get an idea still don't like speed bumps and parking lots with a step transition but seems like its going to be okay on 98%+ of public roads
#14
Member
Thread Starter
iTrader: (4)
Join Date: Dec 2010
Location: Virginia
Posts: 122
Likes: 0
Received 0 Likes
on
0 Posts
Car: 88 Iroc Z
Engine: L98 350
Transmission: 700 R4
Re: help!!!in exhaust shop 2210 can i fit dual 3" to third member?
The last pic I think the guy got a lit excessive on the bend but not to bad. If I ever redo it ill send this section of exhaust in and get it redone in oval
#15
Supreme Member
Join Date: Apr 2010
Location: Modesto, California
Posts: 1,015
Likes: 0
Received 5 Likes
on
4 Posts
Car: 88 Firebird Formula
Engine: LO5 5.7 TBI/Ebl Flash
Transmission: 700R4
Axle/Gears: 2.73 stock rear end
Re: help!!!in exhaust shop 2210 can i fit dual 3" to third member?
Looks 1000X better than previous setup, i like it!!!! Except that last pic showing how much he had to hammer it in/bend it to fit, ouch.
Thread
Thread Starter
Forum
Replies
Last Post
Street Lethal
Power Adders
634
04-30-2019 12:14 PM
ambainb
Camaros for Sale
11
04-25-2016 09:21 PM