Ashtray 12v Outlet
08-09-2014, 07:51 PM
#1
Supreme Member
Thread Starter
iTrader: (6)
Join Date: Oct 2006
Location: West of Toronto
Posts: 3,041
Likes: 0
Received 7 Likes
on
7 Posts
Car: 89 IROC
Engine: 305 TPI / ZZ4 cam
Transmission: Stage 2 700R4, LS1 driveshaft
Axle/Gears: Strange 3.42 w/ Auburn
Ashtray 12v Outlet
I decided to add a 12v outlet to where the ashtray goes. Between the GPS, phone charger, etc, might be a good idea to add another outlet.
Picked up a NOS 4th gen cig lighter and outlet complete from ebay. Also bought the element to attach to the bottom of the outlet and will u=run the wire to a constant power source.
NOS shifter plate
Took a piece of 1/8" plexi (scrap), added some tape to the top, traced out the shape and used a jig to cut out the piece. After smoothed out the edges and hole with a file.
Back looks good
Test fit....seems OK. Lots of space for future accessory button. Will paint the back of the plexi so it will look clear when installed.
Only took 30 min or so.
Picked up a NOS 4th gen cig lighter and outlet complete from ebay. Also bought the element to attach to the bottom of the outlet and will u=run the wire to a constant power source.
NOS shifter plate
Took a piece of 1/8" plexi (scrap), added some tape to the top, traced out the shape and used a jig to cut out the piece. After smoothed out the edges and hole with a file.
Back looks good
Test fit....seems OK. Lots of space for future accessory button. Will paint the back of the plexi so it will look clear when installed.
Only took 30 min or so.
08-09-2014, 08:23 PM
#2
09-01-2014, 04:03 PM
#3
Supreme Member
Thread Starter
iTrader: (6)
Join Date: Oct 2006
Location: West of Toronto
Posts: 3,041
Likes: 0
Received 7 Likes
on
7 Posts
Car: 89 IROC
Engine: 305 TPI / ZZ4 cam
Transmission: Stage 2 700R4, LS1 driveshaft
Axle/Gears: Strange 3.42 w/ Auburn
Re: Ashtray 12v Outlet
Finished pic. Painted the back side in a satin. Coming thru the plexi, it looks clear and bright.
12-02-2014, 03:11 PM
#4
Junior Member
Join Date: Sep 2014
Posts: 22
Likes: 0
Received 0 Likes
on
0 Posts
Car: 88 Camaro IROC-Z
Engine: L03 5.0L
Transmission: T5
Axle/Gears: 3.08
Re: Ashtray 12v Outlet
would you by any chance be able to give me measurements of the plexi glass plate you made? I am going to attempt to make one but am not with me car to measure
12-03-2014, 06:34 PM
#5
Supreme Member
Thread Starter
iTrader: (6)
Join Date: Oct 2006
Location: West of Toronto
Posts: 3,041
Likes: 0
Received 7 Likes
on
7 Posts
Car: 89 IROC
Engine: 305 TPI / ZZ4 cam
Transmission: Stage 2 700R4, LS1 driveshaft
Axle/Gears: Strange 3.42 w/ Auburn
Re: Ashtray 12v Outlet
Width is 1 11/16"
Hole diameter is 7/8"
Distance from end to hole lip is 1 1/8"
Don't forget to add the notches to clear the lid hinge.
12-03-2014, 10:13 PM
#6
Junior Member
Join Date: Sep 2014
Posts: 22
Likes: 0
Received 0 Likes
on
0 Posts
Car: 88 Camaro IROC-Z
Engine: L03 5.0L
Transmission: T5
Axle/Gears: 3.08
Re: Ashtray 12v Outlet
thanks a lot one more question would you by any chance know how far from the top and side edges can not be used bc of the ledge it sits on?
12-04-2014, 05:27 PM
#7
Supreme Member
Thread Starter
iTrader: (6)
Join Date: Oct 2006
Location: West of Toronto
Posts: 3,041
Likes: 0
Received 7 Likes
on
7 Posts
Car: 89 IROC
Engine: 305 TPI / ZZ4 cam
Transmission: Stage 2 700R4, LS1 driveshaft
Axle/Gears: Strange 3.42 w/ Auburn
Re: Ashtray 12v Outlet
Side edge is 1/2"
The ashtray opening is 1 1/2" wide
The ashtray opening is 1 1/2" wide
Thread
Thread Starter
Forum
Replies
Last Post
88SS6SPEED
Engine/Drivetrain/Suspension Parts for Sale
7
11-11-2015 07:05 AM