Third Generation F-Body Message Boards

Search: Posts Made By: ItalianIroc-Z
Showing results 1 to 29 of 29
Search took 0.05 seconds.
Forum: Engine Swap
09-04-2017, 10:10 PM
Replies: 2
Views: 549
Posted By ItalianIroc-Z

Cracked head

i have a 427 with 840 heads what are the chances that the heads are craked and iscausing my overheating it is .030 bored

i am having hard time with that heat and thats why i am looking at a...
Forum: Cooling
09-04-2017, 04:38 PM
Replies: 4
Views: 808
Posted By ItalianIroc-Z

Re: How to get more air flow to the rad

ok cool thanks
Forum: Cooling
09-03-2017, 09:02 AM
Replies: 4
Views: 808
Posted By ItalianIroc-Z

How to get more air flow to the rad

Hi guys how did you guys do it to get more air towards your rad ?
Forum: Engine Swap
08-04-2017, 07:08 PM
Replies: 1
Views: 1,786
Posted By ItalianIroc-Z

Bigger oil pan

guys i am thinking of putting a moroso 7.5L oil pan on my 427 but will not quite fit in my third gen without griding the K member is it that much a better improvement for the engine compare to a 5. L...
Forum: Engine Swap
08-03-2017, 05:50 AM
Replies: 1
Views: 648
Posted By ItalianIroc-Z

427 overheating

I have a big block chevy with an overheating problem can i be caused by a head gasket cooling system can not be any newer or bigger
Forum: Suspension and Chassis
08-03-2017, 05:48 AM
Replies: 4
Views: 550
Posted By ItalianIroc-Z

Re: Front subframe

I haven't yet just tried gonna try this weekend
Forum: Suspension and Chassis
08-01-2017, 10:33 AM
Replies: 4
Views: 550
Posted By ItalianIroc-Z

Re: Front subframe

ok i didnt think of making a small hole to pass lubricant on the bolt

thank you
Forum: Suspension and Chassis
08-01-2017, 10:19 AM
Replies: 4
Views: 550
Posted By ItalianIroc-Z

Front subframe

hi guys

i have a 1986 camaro with the front subframe bolts that wont come out i dont really feel like cutting thru the frame to reach the nuts what is another solution to remove the bolts
...
Forum: Body
06-12-2014, 11:07 PM
Replies: 10
Views: 1,264
Posted By ItalianIroc-Z

Re: doors hinges

ok thanks but do i really need to remove my fender or there is a way to do it without removing the fenders ??
Forum: Body
06-12-2014, 10:05 AM
Replies: 10
Views: 1,264
Posted By ItalianIroc-Z

doors hinges

hii guys ... i have my doors hinges bushing to replace and i was wondering if there is an easy way to do it my car is fully assembled and painted
Forum: Brakes
03-20-2014, 12:26 PM
Replies: 0
Views: 384
Posted By ItalianIroc-Z

brake lines

i have a 1986 camaro iroc and i want to put a line lock but i need to know all the info i need before like brake line size and the fitting sizes please thanks
Forum: Brakes
02-12-2014, 04:11 PM
Replies: 81
Views: 10,427
Posted By ItalianIroc-Z

Re: wilwoods 140-11275 kit

I have been looking at a big brake kit for my 1986 camaro but there are so many choices .... first by putting a bigger rotor i would need to cut the 2 pieces of the spindle going over the stock...
Forum: Auto Detailing and Appearance
02-12-2014, 03:58 PM
Replies: 43
Views: 26,613
Posted By ItalianIroc-Z

Re: August COTM ** Winner **

whats brand mags and where you got them ?
Forum: Suspension and Chassis
12-13-2013, 11:28 AM
Replies: 0
Views: 370
Posted By ItalianIroc-Z

Coil springs

Hi does anyone know the stock spring height for a 1986 camaro Iroc-z thanks
Forum: Transmissions and Drivetrain
09-06-2013, 05:12 PM
Replies: 3
Views: 498
Posted By ItalianIroc-Z

Re: speedo cable help!

ok to remove it you shouldnt get more that a couple of drops of oil ... than to check the cable ... put and electric drill to the tranny end on the cable spin it and see if you gauge goes up or not
Forum: Transmissions and Drivetrain
09-06-2013, 05:10 PM
Replies: 10
Views: 813
Posted By ItalianIroc-Z

Vibration 60mph

I took my car on the freeway and at 55 mph i start having a vibration coming from the under car ... my first tough was that my i needed to balance my driveshaft but i need more info before ... i put...
Forum: Cooling
08-09-2013, 09:20 PM
Replies: 6
Views: 796
Posted By ItalianIroc-Z

Re: overheating 427

i over heat while driving and on idle ... i did bleed the system and yes the fans are working properly ... i have a feeling that my gauge and/or sensor is defective
Forum: Cooling
08-09-2013, 08:38 PM
Replies: 6
Views: 796
Posted By ItalianIroc-Z

overheating 427

I have a 427 bbc with an over heating problem. should i replace the 50/50 coolant with only distilled water ? if not what should i do ? i have 160 degrees thermostat and i cant seem to lower the...
Forum: Body
07-26-2013, 05:03 PM
Replies: 1
Views: 395
Posted By ItalianIroc-Z

cylinder lock

hii I have little question for you ... im having problems with my key lock cylinder ... can anybody send me a picture of how to place the rod ... cuz evertime i turn the key the rod unhooks
thanks
Forum: Electronics
01-14-2013, 11:27 PM
Replies: 9
Views: 775
Posted By ItalianIroc-Z

Re: hatch pull down

Okok i will try thanks alot
Forum: Electronics
01-14-2013, 10:51 PM
Replies: 9
Views: 775
Posted By ItalianIroc-Z

Re: hatch pull down

I have a similar problem I connected the red/white wire to the fuse box and when I get the motor to come up and latch the hatch it will pull down but when I go to release it won't come up .... The...
Forum: Electronics
11-08-2012, 03:04 AM
Replies: 13
Views: 44,486
Posted By ItalianIroc-Z

Re: 1986 camaro steering column wiring diagram

It does help a lot .... Thanks
Forum: Electronics
11-07-2012, 06:01 PM
Replies: 13
Views: 44,486
Posted By ItalianIroc-Z

1986 camaro steering column wiring diagram

Hi everybody,
I am rewiring my interior, and I am looking for the wiring diagram for the column (ignition switch)

Can you plz help me
Forum: Transmissions and Drivetrain
04-15-2012, 08:46 PM
Replies: 0
Views: 527
Posted By ItalianIroc-Z

tremec + 427 bbc

Hi guys i have a tremec tko with a 427 big block chevy and my slave cylinder is too close to my headers ?? .... is there a way to relocate the slave cylinder 1-2 inches to the side or would i have to...
Forum: Electronics
04-07-2012, 10:21 AM
Replies: 0
Views: 615
Posted By ItalianIroc-Z

fuel level sensor

Hello guys I have a question for you I'm putting an after market fuel level gauge inside my 1986 camaro and wanted to know with one to take does anyone have the wiring diagram for the fuel level...
Forum: Suspension and Chassis
03-01-2012, 10:53 PM
Replies: 20
Views: 2,691
Posted By ItalianIroc-Z

Re: Another Subframe connector post!

ok thanks for your help i was trying to put them on and i didn't have any problems up too now but thanks for the advise :)
Forum: Suspension and Chassis
02-28-2012, 07:25 PM
Replies: 20
Views: 2,691
Posted By ItalianIroc-Z

Re: Another Subframe connector post!

hello I wanted to know if putting both inner and outer subframe connectors is a good idea ... i currently have inner tubular connectors and I just bought a pair of outer connectors from competition...
Forum: Electronics
09-09-2011, 12:48 PM
Replies: 2
Views: 791
Posted By ItalianIroc-Z

Re: Speedometer not working?

ok if I'm right your speedometer is mechanically driven .... if it is unplug the cable and check for defaults .. if nothing seems wrong it can be your gauge ... what i did to figure it out on my car...
Forum: Interior
09-06-2011, 12:46 PM
Replies: 10
Views: 3,264
Posted By ItalianIroc-Z

Re: cluster ideas.

hey whats the year of your camaro because the are mechanical driven the original gauges and i wanted to know if you had to do any radical mods ??
Showing results 1 to 29 of 29


 
Forum Jump


All times are GMT -5. The time now is 06:01 PM.