Third Generation F-Body Message Boards

 
Page 1 of 4
1
2
3
4
Search: Posts Made By: acidpad
Showing results 1 to 50 of 185
Search took 0.22 seconds.
Forum: Interior Parts for Sale
05-06-2009, 05:19 PM
Replies: 32
Views: 1,464
Posted By acidpad

Re: Parting out 91RS - MINT Dash pad

I dont - I left those on the car - didnt even think about them. Check with 89Camaro89MI, he might be willing to sell it to you.
Forum: Interior Parts for Sale
05-04-2009, 05:34 PM
Replies: 32
Views: 1,464
Posted By acidpad

Re: Parting out 91RS - MINT Dash pad

Airbag is gone with the car, but it wasnt in great shape anyway. as far as the trunk panel - are you talking about the very back interior plastic panel that spans close to the whole width of the...
Forum: Interior Parts for Sale
05-04-2009, 04:11 PM
Replies: 32
Views: 1,464
Posted By acidpad

Re: Parting out 91RS - MINT Dash pad

I Just checked the lid and deemed it garbage. The underside plastic is cracking or cracked off over most of it, both the inside piece and the outer piece. The foam is out of shape around the edges,...
Forum: Camaros Wanted
05-04-2009, 03:34 PM
Replies: 8
Views: 585
Posted By acidpad

Re: looking for a car in michigan

Hmmm - that car sounds familiar ;)
Forum: Interior Parts for Sale
05-01-2009, 03:30 PM
Replies: 32
Views: 1,464
Posted By acidpad

Re: Parting out 91RS - MINT Dash pad

Dash pad is available again - deal fell through, yet again. As far as pictures go - see above. If you want more, let me know I suppose.
Forum: Interior Parts for Sale
04-22-2009, 09:07 AM
Replies: 32
Views: 1,464
Posted By acidpad

Re: Parting out 91RS - MINT Dash pad

I still have a lot of parts - I will try to get pictures up of everything soon.
Forum: Interior Parts for Sale
04-15-2009, 10:23 AM
Replies: 32
Views: 1,464
Posted By acidpad

Re: Parting out 91RS - MINT Dash pad

I have the ground effect pieces and the grill. The front GFX piece is cracked, other than that they are good. I'll have to come up with a price - let me know if your interested and I'll figure it...
Forum: Interior Parts for Sale
04-11-2009, 03:14 PM
Replies: 32
Views: 1,464
Posted By acidpad

Re: Parting out 91RS - MINT Dash pad

Prickly - I dont see why not. Let me see if I can pull it today.
Forum: Interior Parts for Sale
04-09-2009, 11:43 AM
Replies: 32
Views: 1,464
Posted By acidpad

Re: Parting out 91RS - MINT Dash pad

fbodyman - Mine is the canvas rollshade, not the vinyl, it is faded blue. I'll try to get pics on tonight.
price with shipping would be $50. I've got someone else interested too, so let me know if...
Forum: Interior Parts for Sale
04-09-2009, 11:35 AM
Replies: 32
Views: 1,464
Posted By acidpad

Re: Parting out 91RS - MINT Dash pad

I'm in toledo. The steering column is a pass-key security ignition. I'll get pictures of the other pieces up tonight (hopefully). I've got someone thats getting the rolling body mostly for the...
Forum: Interior Parts for Sale
04-08-2009, 11:19 PM
Replies: 32
Views: 1,464
Posted By acidpad

Re: Parting out 91RS - MINT Dash pad

Dash pad is still available - sale fell through.
Forum: Interior Parts for Sale
04-07-2009, 12:32 PM
Replies: 32
Views: 1,464
Posted By acidpad

Re: Parting out 91RS - MINT Dash pad

I do have the roll shade, its a bit faded but otherwise in good shape. I'll get pictures and shipping info for you tomorrow.
Forum: Interior Parts for Sale
04-05-2009, 09:57 PM
Replies: 32
Views: 1,464
Posted By acidpad

Re: Parting out 91RS - MINT Dash pad

Replied to PM
Forum: Camaros for Sale
04-05-2009, 09:52 PM
Replies: 30
Views: 2,431
Posted By acidpad

Re: 91 rs roller - Toledo, OH

parting it out, interior parts listed at
https://www.thirdgen.org/forums/interior-parts-sale/519709-parting-out-91rs-mint.html
Forum: Interior Parts for Sale
04-05-2009, 02:56 PM
Replies: 32
Views: 1,464
Posted By acidpad

Re: Parting out 91RS - MINT Dash pad

rearseat and lower dash mount
Forum: Interior Parts for Sale
04-05-2009, 02:53 PM
Replies: 32
Views: 1,464
Posted By acidpad

Re: Parting out 91RS - MINT Dash pad

more pictures
Forum: Interior Parts for Sale
04-05-2009, 02:51 PM
Replies: 32
Views: 1,464
Posted By acidpad

Parting out 91RS - MINT Dash pad

Got a 73 camaro, and that means that the 91s gotta go. Nobody was interested in buying a roller, so I am parting out my 91. I will post this in stages as I get stuff taken off - if there is...
Forum: Camaros for Sale
04-02-2009, 12:57 PM
Replies: 30
Views: 2,431
Posted By acidpad

Re: 91 rs roller - Toledo, OH

I'm starting to part it out this weekend - I really cant wait much longer on this. Let me know ASAP if your interested, and lets set something up.
Forum: Camaros for Sale
03-28-2009, 05:40 PM
Replies: 30
Views: 2,431
Posted By acidpad

Re: 91 rs roller - Toledo, OH

You are right, scrap isnt worth a whole lot right now - but the t-tops, dash (dashpad is in perfect shape btw), rear hatch assembly, door panels etc are easily worth more than the $500 im asking. ...
Forum: Camaros for Sale
03-28-2009, 04:27 PM
Replies: 30
Views: 2,431
Posted By acidpad

Re: 91 rs roller - Toledo, OH

Underneath is a mixed bag. at the very rear, going across the back behind the gfx theres alot of rust. The floors are moderate, and the actual frame rails are in good shape. Its not going to be...
Forum: Camaros for Sale
03-28-2009, 09:41 AM
Replies: 30
Views: 2,431
Posted By acidpad

Re: 91 rs roller - Toledo, OH

more
Forum: Camaros for Sale
03-28-2009, 09:39 AM
Replies: 30
Views: 2,431
Posted By acidpad

Re: 91 rs roller - Toledo, OH

Havent had the chance to wash it (and i'm probably not going to have that chance), but here are some new pictures now that its out. The tiedown straps in the front are holding up the exhaust and the...
Forum: Camaros for Sale
03-24-2009, 11:08 PM
Replies: 30
Views: 2,431
Posted By acidpad

Re: 91 rs roller - Toledo, OH

If I don't have any takers by sunday its getting parted out. If anyones interested, lets figure something out now.
Forum: Camaros for Sale
03-21-2009, 02:32 AM
Replies: 30
Views: 2,431
Posted By acidpad

Re: 91 rs roller - Toledo, OH

Yes, there is a dent in the rear bumper on the passenger corner. That is one reason why the price is so low. At the $500 mark, nobody should be expecting a mint vehicle - period. This car does...
Forum: Camaros for Sale
03-20-2009, 10:55 AM
Replies: 30
Views: 2,431
Posted By acidpad

Re: 91 rs roller - Toledo, OH

Yeah, it'll go back together fine. I was in the process of converting it to put my carbed 400 in, so I took the dash apart to pull the computer. Let me know if your coming by on saturday - it is...
Forum: Camaros for Sale
03-19-2009, 12:25 PM
Replies: 30
Views: 2,431
Posted By acidpad

Re: 91 rs roller - Toledo, OH

I do not have a way to deliver it - that is the responsibility of the buyer. I can tell you that to get my 73 from NC to here, I used a truck and a tow dolley (rented from American RentAll - $45 /...
Forum: Camaros for Sale
03-14-2009, 11:45 PM
Replies: 30
Views: 2,431
Posted By acidpad

Re: 91 rs roller - Toledo, OH

More pictures of interior. These are from before the interior was taken apart. The pieces are still in this shape, but the dash is taken apart (all pieces are there, not more than a few hours to...
Forum: Camaros for Sale
03-11-2009, 05:09 PM
Replies: 30
Views: 2,431
Posted By acidpad

Re: 91 rs roller - Toledo, OH

honestly, i'm not sure about underneath. its in a popup garage right now, and the ground is failry muddy, and I'm not inclined to get under it to check until I get it moved. That should be sometime...
Forum: Camaros for Sale
03-11-2009, 02:26 AM
Replies: 30
Views: 2,431
Posted By acidpad

Re: 91 rs roller - Toledo, OH

Car was originally teal, and no, it wasnt spray bombed. It had a Maaco paint job a few years ago. Rust isn't horrible . Passenger fender has a spot about 2 inches long, 1 inch wide. There is a...
Forum: Camaros for Sale
03-10-2009, 11:37 AM
Replies: 30
Views: 2,431
Posted By acidpad

Re: 91 rs roller - Toledo, OH

Someone make me an offer and lets get this gone
Forum: Camaros for Sale
03-09-2009, 01:34 AM
Replies: 30
Views: 2,431
Posted By acidpad

Re: 91 rs roller - Toledo, OH

pics now posted for everyone - It took me longer than I wanted to get the pictures, so its going to be a few more days before I have to make the decision on it. Probably until the end of this week. ...
Forum: Camaros Wanted
03-06-2009, 12:41 PM
Replies: 8
Views: 585
Posted By acidpad

Re: looking for a car in michigan

If your looking for a project car, check this out ... I'm just down in toledo, right outside MI.

https://www.thirdgen.org/forums/camaros-sale/514885-91-rs-roller-toledo.html
Forum: Camaros for Sale
03-06-2009, 11:47 AM
Replies: 30
Views: 2,431
Posted By acidpad

91 rs roller - Toledo, OH

I've recently purchased a 73 camaro, and that means the 91 has to go - quick. I'm looking to get $500, but I will entertain any serious offer that can have the car gone by the end of the weekend. ...
Forum: Aftermarket Product Review
04-01-2008, 10:28 PM
Replies: 6
Views: 1,452
Posted By acidpad

Re: Iron Eagle 215 platinum questions

Honestly, thats what I'm hoping for. I havent had the chance to measure them yet though, the heads are in a buddy's garage along with the rest of my engine due to a lack of room in my current...
Forum: Aftermarket Product Review
04-01-2008, 02:23 PM
Replies: 6
Views: 1,452
Posted By acidpad

Re: Iron Eagle 215 platinum questions

Right now I'm just trying to get a base line so that I can estimate my torque curve and choose the right torque converter, or make the decision to take the hard route and switch to a manual...
Forum: Aftermarket Product Review
03-31-2008, 02:52 PM
Replies: 6
Views: 1,452
Posted By acidpad

Iron Eagle 215 platinum questions

In the process of building up my 406, i bought a set of iron eagle 215 heads. I'm finally trying to get around to finishing the engine up, and was looking at the heads again.

according to darts...
Forum: Engine/Drivetrain/Suspension Parts for Sale
11-13-2006, 01:28 PM
Replies: 7
Views: 445
Posted By acidpad

I've got one I pulled from my 91 rs. Its already...

I've got one I pulled from my 91 rs. Its already pulled and still attached to the engine and in the back of my truck. I'm in toledo OH if your interested. I could probably do $100 on it. Nothing...
Forum: Tech / General Engine
10-05-2006, 11:59 PM
Replies: 10
Views: 6,362
Posted By acidpad

Hey, Thanks for the replies. The Ohio Crank...

Hey,

Thanks for the replies. The Ohio Crank H-Beams use cap screws so they are suppose to be some of the best you can get for clearence in these type situations. There is not much material...
Forum: Tech / General Engine
10-05-2006, 04:52 PM
Replies: 4
Views: 562
Posted By acidpad

I think that if your taking your heads off anyway...

I think that if your taking your heads off anyway to work on the valves and you have about a grand, i might look into getting some used vortec heads and a set of headers. Intake and carb tuning...
Forum: Tech / General Engine
10-05-2006, 04:34 PM
Replies: 10
Views: 6,362
Posted By acidpad

chevy 400SB cam/rod clearence

I did a mockup of my 406 today, but i don't have a timing chain yet. When i put everything in and cycle the crank and the cam by hand, at certain points the rods (there are 2 of them that hit, but...
Forum: Tech / General Engine
09-21-2006, 11:17 PM
Replies: 26
Views: 1,553
Posted By acidpad

I recently just bought some forged probe pistons...

I recently just bought some forged probe pistons and couldnt be happier with them. Check them out, they are cheaper than the rest and seem to be on par with craftsmanship.
Forum: Tech / General Engine
09-20-2006, 10:59 PM
Replies: 7
Views: 573
Posted By acidpad

i'm gonna go out on a limb and guess that you...

i'm gonna go out on a limb and guess that you have a manual tranny. If thats the case, that sound your hearing is the throwout bearing going. If its the throwout, the sound will also stop when you...
Forum: Tech / General Engine
09-20-2006, 10:51 PM
Replies: 3
Views: 408
Posted By acidpad

when you are using your remote start, do you have...

when you are using your remote start, do you have the key in the on position ? if not, give that a shot.
Forum: Tech / General Engine
06-14-2006, 11:08 PM
Replies: 3
Views: 440
Posted By acidpad

I'll take a stab at this, but I am by no means an...

I'll take a stab at this, but I am by no means an expert.

I am just finishing up building a 406, so I do have a bit of experience. If you look through CHP you will see that they build a 400 with...
Forum: Tech / General Engine
05-23-2006, 10:39 PM
Replies: 12
Views: 868
Posted By acidpad

i dont actually think that i'm in too bad of a...

i dont actually think that i'm in too bad of a position right now. Im looking at the following.

1) the cam i listed stays
2) heads staying at 64cc
3) 15 cc dish pistons
4) either run a .021...
Forum: Power Adders
05-23-2006, 09:12 PM
Replies: 10
Views: 868
Posted By acidpad

still working the whole head gasket thing out ....

still working the whole head gasket thing out ....
Forum: Tech / General Engine
05-23-2006, 09:11 PM
Replies: 15
Views: 7,221
Posted By acidpad

I think I decided to just order 5.7 H beams and...

I think I decided to just order 5.7 H beams and 15cc dish pistons with 1.425 CH, and check from there. From there, seeing as how I'm going to keep the quench at ~ .04 - .045, I'll measure how far in...
Forum: Tech / General Engine
05-23-2006, 05:02 PM
Replies: 15
Views: 7,221
Posted By acidpad

how can i measure the deck height for sure .... I...

how can i measure the deck height for sure .... I checked my cyinder wall height, and got 6.125" Not really sure where to go from there, i tried measuring center of the mains upto the deck, but...
Forum: Tech / General Engine
05-23-2006, 03:23 PM
Replies: 15
Views: 7,221
Posted By acidpad

"I dont have pistons yet or rods yet" "does...

"I dont have pistons yet or rods yet"
"does anyone know where you can find one [head gasket]"

Exactly what part of that says that I'm piecing together stuff I have laying around......


It...
Forum: Tech / General Engine
05-23-2006, 02:45 PM
Replies: 15
Views: 7,221
Posted By acidpad

I was planning on measuring tonight, right now...

I was planning on measuring tonight, right now the block is bare, so what exactly should I measure , the cylinder wall height or from the center of where the crank would be to the deck ? I'm...
Showing results 1 to 50 of 185
 
Page 1 of 4
1
2
3
4


 
Forum Jump


All times are GMT -5. The time now is 10:45 PM.