Third Generation F-Body Message Boards

 
Page 1 of 4
1
2
3
4
Search: Posts Made By: smoktire
Showing results 1 to 50 of 151
Search took 0.15 seconds.
Forum: Organized Drag Racing and Autocross
05-14-2007, 02:31 PM
Replies: 0
Views: 379
Posted By smoktire

Max DCR for 94 octane

Can i run a 355cu Static compresion ratio of 11.20:1 (Dynamic 8.5:1) on 94 octane if i keep the engine temp on 170 deg F :confused:
Forum: Power Adders
05-08-2007, 01:08 PM
Replies: 13
Views: 4,626
Posted By smoktire

Re: nitrous on a 305?

L69 + 75HP shot on 3300Lbs car =
60' 1.73s
1/4 12.79s
mph 105
Forum: Organized Drag Racing and Autocross
05-08-2007, 08:30 AM
Replies: 39
Views: 2,968
Posted By smoktire

Re: Stock 7.625 what's the average best 60' before it breaks

M/T ET Drag 28x9x15 lock right locker stock 3.42 gear.Almost lift the tire off the ground :) at least on thr right side ...i think that on the left it got some air...but no one to tell :rolleyes:
...
Forum: Organized Drag Racing and Autocross
05-06-2007, 09:41 PM
Replies: 39
Views: 2,968
Posted By smoktire

Re: Stock 7.625 what's the average best 60' before it breaks

Just got 1.73 out of it :nod: with a all internal stock l69 on 75hp shot ....
Forum: Cooling
02-09-2007, 09:03 AM
Replies: 8
Views: 1,537
Posted By smoktire

Nice setup rtkjadams :eek: How it run on the 1/4...

Nice setup rtkjadams :eek: How it run on the 1/4 ? ....I put it on the key switch with a separate switch for manual overridind.Work verry good .I let the temp raise to 195 then shut the engine start...
Forum: Cooling
02-07-2007, 11:07 PM
Replies: 8
Views: 1,537
Posted By smoktire

Just made a home made braket so for thoses who...

Just made a home made braket so for thoses who whant to see it here is the pic...

http://img247.imageshack.us/img247/2415/imm368nd2.jpg (http://imageshack.us)
Forum: Cooling
02-05-2007, 10:49 PM
Replies: 8
Views: 1,537
Posted By smoktire

I got a s-10 manual stering box and i moved the...

I got a s-10 manual stering box and i moved the alternator to the left lower side but i need to make a kind of belt ajustment....
Forum: Organized Drag Racing and Autocross
02-05-2007, 08:42 AM
Replies: 4
Views: 441
Posted By smoktire

Wow killer camaro :eek:

Wow killer camaro :eek:
Forum: Cooling
02-04-2007, 12:27 AM
Replies: 8
Views: 1,537
Posted By smoktire

Proform or other Electric water pump instaled picture

Plz post a pic of your electric water pump .Do it work good for the street :confused:
Forum: Organized Drag Racing and Autocross
12-18-2006, 11:24 AM
Replies: 26
Views: 5,515
Posted By smoktire

Since i had a rod failure and had to tear out the...

Since i had a rod failure and had to tear out the engine taking pics was easy. This is what the prints on the crank snout looks pretty well :)
...
Forum: Organized Drag Racing and Autocross
12-17-2006, 10:06 PM
Replies: 6
Views: 1,474
Posted By smoktire

What is bether L69 or LO5

Do if change my L69 305ho for a LO5 350 (stock except for a XE268 cam) worth the swap.The 350 is free $ just need to replace the cam & some gasket :hmmm:
My old 355 flat top piston with the XE268...
Forum: Organized Drag Racing and Autocross
12-16-2006, 01:21 PM
Replies: 40
Views: 1,514
Posted By smoktire

With my old vortec setup 355ci ,9.73:1cr ,XE268...

With my old vortec setup 355ci ,9.73:1cr ,XE268 cam with 1.6 roller rockers, manley under cut racing valve ,RPM air gap intake ,4150HP 650 carb ,msd box , P/S and Alternator working,th700 no stall...
Forum: Organized Drag Racing and Autocross
12-15-2006, 11:56 PM
Replies: 40
Views: 1,514
Posted By smoktire

This guy did nice time with vortec heads...

This guy did nice time with vortec heads :thumbsup:

http://www.cardomain.com/ride/275092
Forum: Transmissions and Drivetrain
10-13-2006, 12:23 AM
Replies: 4
Views: 863
Posted By smoktire

I was using a th700 with 4.10 with 27"tires it...

I was using a th700 with 4.10 with 27"tires it was fine like 2300rpm at 65MPH.
Then i swap to a th350 still hade th 4.10 it was ugly 3500 at 60mph so i switch to a 3.42 its now pretty fine for me...
Forum: Tech / General Engine
10-08-2006, 10:56 PM
Replies: 8
Views: 608
Posted By smoktire

i got great results with 906 vortec heads on a...

i got great results with 906 vortec heads on a 355ci 13.1@104 no stall 3.42 gear
Forum: Transmissions and Drivetrain
10-08-2006, 10:44 PM
Replies: 2
Views: 357
Posted By smoktire

TH700

TH700
Forum: Organized Drag Racing and Autocross
10-08-2006, 07:15 PM
Replies: 6
Views: 932
Posted By smoktire

305HO + th350 trans + 3000 stall + slicks +...

305HO + th350 trans + 3000 stall + slicks + Lakewood LCA +V6 rear spring + removed front sway bar - the rest is all stock = 1.93 60' & 14.34@93MPH 1\4 mile
Forum: Organized Drag Racing and Autocross
10-07-2006, 07:09 PM
Replies: 4
Views: 703
Posted By smoktire

Just went to the track and run a nice 14.34 at...

Just went to the track and run a nice 14.34 at 93.06 mph all stock inside L69 :burnout:

http://img152.imageshack.us/img152/180/camarcd8.jpg (http://imageshack.us)

A video of 14.47s
...
Forum: Organized Drag Racing and Autocross
10-06-2006, 12:55 AM
Replies: 4
Views: 703
Posted By smoktire

L69 vs 1320

What is the average 1/4 mile for the L69 with auto trans :driving:
Forum: Carburetors
07-29-2006, 11:57 AM
Replies: 1,335
Important/Useful : Post Your Carb'd Motor Pics
Views: 315,231
Posted By smoktire

new one

my new problems

http://img125.imageshack.us/img125/537/imm350ol6.jpg (http://imageshack.us)
Forum: Fabrication
07-01-2006, 02:30 PM
Replies: 6
Views: 1,534
Posted By smoktire

here more Its made from scrap piece of soft...

here more

Its made from scrap piece of soft steel electrical motor shaft & little of arc welding

http://img56.imageshack.us/img56/2638/imm3408iq.jpg (http://imageshack.us)
...
Forum: Fabrication
07-01-2006, 02:14 PM
Replies: 6
Views: 1,534
Posted By smoktire

Home made rod bolt strech guage

What do you think about my home made rod bolt stretch gauge . I test it on a old rod .006" of stretch give me 45ft lbs on the torque wrench :thumbsup:

...
Forum: Organized Drag Racing and Autocross
06-02-2006, 09:23 AM
Replies: 1
Views: 745
Posted By smoktire

yeah this ...

yeah this

http://img78.imageshack.us/img78/451/12068rs.jpg (http://imageshack.us)
Forum: Organized Drag Racing and Autocross
05-30-2006, 08:15 AM
Replies: 4
Views: 1,793
Posted By smoktire

Just call comp cams and they said that cams...

Just call comp cams and they said that cams finishing with a 8 like 12-772-8 are cast and they can be used with the stock distibutor gear & fuel pump push rod so no need for the bronze thing.
Forum: Tech / General Engine
05-30-2006, 08:14 AM
Replies: 4
Views: 765
Posted By smoktire

Just call comp cams and they said that cams...

Just call comp cams and they said that cams finishing with a 8 like 12-772-8 are cast and they can be used with the stock distributor gear & fuel pump push rod so no need for the bronze thing.
Forum: Organized Drag Racing and Autocross
05-23-2006, 10:46 PM
Replies: 26
Views: 5,515
Posted By smoktire

Yes its food for the tougt...i still have my dye...

Yes its food for the tougt...i still have my dye idea i will let you know the results with the pics when i will finally have the time to does it :cool:
Forum: Organized Drag Racing and Autocross
05-23-2006, 12:14 PM
Replies: 26
Views: 5,515
Posted By smoktire

The 45 Deg. ridge of the male "spline" ares...

The 45 Deg. ridge of the male "spline" ares about .036" too inside compare to the stock one so they look to be little stress point on the chamfer on the crank snout.A little dremel work should take...
Forum: Organized Drag Racing and Autocross
05-21-2006, 05:24 PM
Replies: 26
Views: 5,515
Posted By smoktire

Thanks i will put some dye on the snout R&R the...

Thanks i will put some dye on the snout R&R the sproket & take a looks at the prints to see how much i need to remove :cool:
Forum: Organized Drag Racing and Autocross
05-21-2006, 03:35 PM
Replies: 26
Views: 5,515
Posted By smoktire

Does the chamfers on this one looks ok to you ? ...

Does the chamfers on this one looks ok to you ?

http://img270.imageshack.us/img270/8651/as7do.jpg (http://imageshack.us)
Forum: Organized Drag Racing and Autocross
05-19-2006, 11:15 PM
Replies: 26
Views: 5,515
Posted By smoktire

Ok so i just buy a Comp Cams billet double roller...

Ok so i just buy a Comp Cams billet double roller PN:7100 :nod: Looks verry good..!

http://img191.imageshack.us/img191/3369/194306176full1lr.jpg (http://imageshack.us)
Forum: Aftermarket Product Review
04-24-2006, 10:47 PM
Replies: 7
Views: 1,406
Posted By smoktire

The axle ...for the pushrod theres a other hole...

The axle ...for the pushrod theres a other hole on the side.
Forum: Organized Drag Racing and Autocross
04-23-2006, 06:57 PM
Replies: 4
Views: 1,793
Posted By smoktire

distributor gear with cast roller cam

With a cast core solid roller cam do i need to run a bronze distributor gear or the stock one is ok Cam is Comp cams 12-772-8 XR286
...
Forum: Aftermarket Product Review
04-23-2006, 06:34 PM
Replies: 7
Views: 1,406
Posted By smoktire

Yes your are right Luskville dragway :nod:

Yes your are right Luskville dragway :nod:
Forum: Aftermarket Product Review
04-23-2006, 12:06 PM
Replies: 7
Views: 1,406
Posted By smoktire

Comp cams Solid roller cam & Hi-tech lifter

The Hi-tech lifter are not suposed to be used for sustained idle cause the main oiling is crank oil splaching on it...I alredy got the Hi-tech one So i check the endurex ones with a groove on it that...
Forum: Tech / General Engine
04-23-2006, 09:38 AM
Replies: 4
Views: 765
Posted By smoktire

No one knows !?

No one knows !?
Forum: Tech / General Engine
04-22-2006, 10:04 PM
Replies: 4
Views: 765
Posted By smoktire

Cast core roller cam & distributor gear

With a cast core solid roller cam do i need to run a bronze distributor gear or the stock one is ok :confused: Cam is Comp cams 12-772-8
Forum: Organized Drag Racing and Autocross
04-19-2006, 08:07 AM
Replies: 26
Views: 5,515
Posted By smoktire

The main reason is that the proform thing include...

The main reason is that the proform thing include plate lock - bottom - thrust with a less expensive price of a chain with all theses and its suposed to be stronger than a chain. I will run a HV HP...
Forum: Organized Drag Racing and Autocross
04-18-2006, 11:53 AM
Replies: 26
Views: 5,515
Posted By smoktire

Proform gear drive ?

What do you think about Proform gear drive :confused: The edelbrock one is 159$ the pete jackson 145$ the summit 119 and the proform is only 83$ is it a good products ... :huh:
Forum: Organized Drag Racing and Autocross
04-12-2006, 12:43 PM
Replies: 2
Views: 575
Posted By smoktire

Thanks silverbullet

Thanks silverbullet
Forum: Organized Drag Racing and Autocross
04-12-2006, 10:30 AM
Replies: 2
Views: 575
Posted By smoktire

Stock conrod Hp/rpm rating

What hp and rpm stock conecting rod will survive ?
Forum: Suspension and Chassis
02-16-2006, 12:32 PM
Replies: 2
Views: 2,732
Posted By smoktire

s10 gear box vs camaro p/s

Easy swap ... grind s10 box mounting ears pads flat grind the sway bar braket interchange the pitman arm

http://img157.imageshack.us/img157/8910/stering0194kx.jpg (http://imageshack.us)
Forum: Transmissions and Drivetrain
02-13-2006, 12:27 AM
Replies: 3
Views: 3,172
Posted By smoktire

TH350 best shift kit ?

What is the best shift kit for the th350

-TCI Trans-Scat pn:350000
-B&M Transpak pn:30228
-Transgo pn:350PSK

Transgo says that with their kit the trany should handle 500HP what do you think...
Forum: Power Adders
11-29-2005, 01:29 PM
Replies: 17
Views: 813
Posted By smoktire

8.00 cdn so around 6.80 us per pound

8.00 cdn so around 6.80 us per pound
Forum: Carburetors
11-27-2005, 02:25 AM
Replies: 1,335
Important/Useful : Post Your Carb'd Motor Pics
Views: 315,231
Posted By smoktire

New project

New project
Forum: Organized Drag Racing and Autocross
10-14-2005, 12:14 PM
Replies: 16
Views: 1,259
Posted By smoktire

No body else !?

No body else !?
Forum: Organized Drag Racing and Autocross
10-14-2005, 12:03 PM
Replies: 11
Views: 747
Posted By smoktire

Last year my setup was somewhat like yours stock...

Last year my setup was somewhat like yours stock vortec - manley race flow valve - xe268 cam - 1.6 roller rockers -Air gap rpm intake - holley 600 hp -1 5/8 shorties with 2.750" single exhaust -...
Forum: Organized Drag Racing and Autocross
10-09-2005, 05:18 PM
Replies: 16
Views: 1,259
Posted By smoktire

So with a 383 i should run in the 11s... that...

So with a 383 i should run in the 11s... that make me feel good ;)
Forum: Organized Drag Racing and Autocross
10-07-2005, 01:52 AM
Replies: 16
Views: 1,259
Posted By smoktire

You have nice setup guys :cool: 1 7/8...

You have nice setup guys :cool:

1 7/8 headers ???? what kind are they?
Forum: Organized Drag Racing and Autocross
10-06-2005, 01:38 AM
Replies: 16
Views: 1,259
Posted By smoktire

stunt pump gas 383

Who got fast pump gas 383 with a similar setup as mine .What is your combo and what ares your track time ?

I hesitate on builting a 355 (cr9.75)or 383 (cr11.0)... my goal is to run around 11.6 on...
Forum: Tech / General Engine
10-05-2005, 02:58 PM
Replies: 0
Views: 442
Posted By smoktire

Stunt pump gas 383

Who got fast pump gas 383 with a similar setup as mine .What is your combo and what ares your track time ?

I hesitate on builting a 355 (cr9.75)or 383 (cr11.0)... my goal is to run around 11.6...
Showing results 1 to 50 of 151
 
Page 1 of 4
1
2
3
4


 
Forum Jump


All times are GMT -5. The time now is 06:32 AM.