Third Generation F-Body Message Boards

Search: Posts Made By: oneloudchevy
Showing results 1 to 22 of 22
Search took 0.10 seconds.
Forum: Brakes
05-27-2017, 10:28 AM
Replies: 1
Views: 579
Posted By oneloudchevy

Ls1 master with stock brakes

Can i use the ls1 master with stock iron caliper fronts and rear drums. I plan on installing an adjustable proportioning valve and the c4 front conversion and keeping the rear drums
Forum: LTX and LSX
08-18-2014, 08:16 AM
Replies: 287
Views: 60,417
Posted By oneloudchevy

Re: Watch a Rookie Learn How To Swap a LS1 and T56 into a 1992 Z28

Cant wait to see the jegster torque arm install. I like what you do
Forum: DFI and ECM
07-13-2014, 07:16 PM
Replies: 2
Views: 3,271
Posted By oneloudchevy

Re: Holley HP EFI knock sensor frequency

http://forums.holley.com/showthread.php?2534-Connecting-amp-Tuning-Knock-Sensors-Holley-EFI
Forum: Transmissions and Drivetrain
11-21-2013, 02:54 PM
Replies: 2
Views: 664
Posted By oneloudchevy

Re: Jerico Tranny question ?

https://www.thirdgen.org/forums/transmissions-drivetrain/648140-swapping-jerico-4-seed.html
Forum: Auto Detailing and Appearance
06-12-2004, 05:43 PM
Replies: 33
Views: 7,293
Posted By oneloudchevy

Tkat is a good looking camaro. I like that color...

Tkat is a good looking camaro. I like that color combo. Is it stock.

Here is a pic without the bra
Forum: Auto Detailing and Appearance
06-07-2004, 10:02 PM
Replies: 33
Views: 7,293
Posted By oneloudchevy

Raised white letters vs. Blackwall tires

Ok everyone I need your opinion. Should I stick with the raised white letters or go with blackwalls. I am kind of partial to the white letters but I cant find any tires with a speed rating higher...
Forum: Body
06-06-2004, 01:39 AM
Replies: 27
Views: 2,930
Posted By oneloudchevy

The reason that GM discontinued the hood was...

The reason that GM discontinued the hood was because of water damage to engines
Forum: Auto Detailing and Appearance
06-06-2004, 01:23 AM
Replies: 125
Views: 5,844
Posted By oneloudchevy

That explains why it looks so familiar. Thought...

That explains why it looks so familiar. Thought you guys might find this interesting.
Forum: Suspension and Chassis
04-30-2004, 04:26 PM
Replies: 4
Views: 496
Posted By oneloudchevy

Are the 32 and 21 bar good or should i get new...

Are the 32 and 21 bar good or should i get new bars
Forum: Suspension and Chassis
04-29-2004, 10:08 PM
Replies: 4
Views: 496
Posted By oneloudchevy

sway bars

I was wondering if someone could tell me what size sway bars are on my car. It is a 1984 camaro z28 with a 305 carburated engine.
Forum: Engine Swap
04-21-2004, 02:58 PM
Replies: 3
Views: 587
Posted By oneloudchevy

hood clearance

I am putting a 350 in my 84' z28 and I was wondering if I will have enough hood clearance with the stock hood. I have a weiand action plus manifold and a holley 4160 double pumper.
Forum: Engine Swap
04-21-2004, 01:13 PM
Replies: 10
Views: 524
Posted By oneloudchevy

I think it would be safe to say blocks after 1979...

I think it would be safe to say blocks after 1979 would work
Forum: Engine Swap
04-20-2004, 10:15 AM
Replies: 10
Views: 751
Posted By oneloudchevy

If it is a vaccum leak there is an easy way to...

If it is a vaccum leak there is an easy way to check. Take an oxy acetalene torch and turn on the oxygen only (dont lite it). With the engine warm and idling take the torch and run it all along the...
Forum: Engine Swap
04-20-2004, 12:24 AM
Replies: 10
Views: 524
Posted By oneloudchevy

the block is a 80's block my mistake. Boy...

the block is a 80's block my mistake.

Boy that engine sure is shiny
Forum: Engine Swap
04-19-2004, 02:11 PM
Replies: 10
Views: 524
Posted By oneloudchevy

My 350 is a mid 70s 4-bolt 2 piece main seal

My 350 is a mid 70s 4-bolt 2 piece main seal
Forum: Engine Swap
04-18-2004, 11:21 AM
Replies: 10
Views: 524
Posted By oneloudchevy

350 to t-5

I have an 84' z28 with a carbed lG4 and a borg warner t-5. I want to put a 350 in it and I had some questions about the swap.
I was wondering if the flywheel, cluch, and starter would fit and work...
Forum: Tech / General Engine
04-15-2004, 09:44 PM
Replies: 1
Views: 417
Posted By oneloudchevy

Raocker arms and valve clearences

I want to run 1.6 ratio rocker arms and was wondering if there are any valve to piston clearence issues. The cam that I am using doesnt have over .500in gross lift
Forum: Tech / General Engine
04-02-2004, 04:39 PM
Replies: 2
Views: 438
Posted By oneloudchevy

Valvetrain

Can you use roller rockers on a regular non roller camshaft
Forum: Tech / General Engine
03-19-2004, 04:58 PM
Replies: 2
Views: 464
Posted By oneloudchevy

Cam question

Can you replace a camshaft without replacing the cam bearings.
Forum: Carburetors
03-11-2004, 01:12 AM
Replies: 8
Views: 1,093
Posted By oneloudchevy

Do you still have your cc Q-Jet

Do you still have your cc Q-Jet
Forum: Carburetors
03-10-2004, 07:36 PM
Replies: 8
Views: 1,093
Posted By oneloudchevy

I dont like the computer controlled Q-Jet. I...

I dont like the computer controlled Q-Jet. I dont have anything against Q-Jets I just want something less complicated to tune.
Forum: Carburetors
03-10-2004, 06:31 PM
Replies: 8
Views: 1,093
Posted By oneloudchevy

What Carb Cfm should I use.

I am having a problem deciding what cfm carb to use. I have tried all the equations to figure out what cfm is optimum but it doesnt seem right. I have an 84' camaro z28 with a stock LG4 and a...
Showing results 1 to 22 of 22


 
Forum Jump


All times are GMT -5. The time now is 02:07 PM.