Third Generation F-Body Message Boards

Search: Posts Made By: iroc monster
Showing results 1 to 18 of 18
Search took 0.08 seconds.
Forum: Third Gen Association of Ontario
04-22-2011, 10:11 AM
Replies: 8
Views: 1,173
Posted By iroc monster

Re: Big Event in Oshawa June 2011

Anybody know what time the plant tour is?
Forum: Third Gen Association of Ontario
03-30-2011, 11:10 PM
Replies: 8
Views: 1,173
Posted By iroc monster

Re: Big Event in Oshawa June 2011

Not going to miss that.
Forum: Canadian Region
07-22-2009, 09:37 PM
Replies: 10
Views: 970
Posted By iroc monster

Re: Anyone from Ottawa ON

Well I'm from Ottawa, I go to every cruise night in Hazeldean in Kanata on Tuesday nights, Rideau Carleton Raceway Wed sometimes and Almonte Thu nights when I can. I don't see too many 3rd gens at...
Forum: Engine/Drivetrain/Suspension Parts for Sale
07-23-2008, 06:43 AM
Replies: 0
Views: 457
Posted By iroc monster

Hedman Hedders For Sale Cheap

68470 Shorties
These will fit any 3rd gen Camaros and Firebirds. No leaks or cracks and no O2 sensors.
These were once nicely black painted with special heat paint when they were initially...
Forum: Fabrication
08-28-2007, 09:47 PM
Replies: 35
Views: 32,661
Posted By iroc monster

Re: carb hat idea

I've been reading your thread and I realize it was a couple of years ago. But I also had the same idea and came up with...
Forum: Engine/Drivetrain/Suspension Parts for Sale
08-08-2007, 01:34 PM
Replies: 2
Views: 394
Posted By iroc monster

Hedman Hedders FS Cheap

Hedman Hedders 68470
These have served me well on my 86 IROC. They are very solid with no leaks or cracks and no O2 sensors. They were once nicely painted black when I initially installed them 8...
Forum: Tech / General Engine
10-05-2006, 10:41 PM
Replies: 11
Views: 548
Posted By iroc monster

Well as I suspected, no bad diodes. I plugged my...

Well as I suspected, no bad diodes. I plugged my oscilloscope and got all half positive sine waves, although a little bit of noise but otherwise OK. I called the shop who tested my alt and they...
Forum: Electronics
09-24-2006, 08:49 AM
Replies: 0
Views: 558
Posted By iroc monster

Choke Heater Relay Noise underdash

I've long since replaced the LG4 in my 86 IROC with a kickass 350 and running a manual choke on an Edelbrock 1405 carburetor.
The choke heater relay always made a buzzing sound when I turned the...
Forum: Electronics
09-21-2006, 11:08 PM
Replies: 8
Views: 563
Posted By iroc monster

I have the same problem. I've got the voltage...

I have the same problem. I've got the voltage gauge in the dash showing the battery down to 10.5V when I'm idleling at a stop light with headlights ON and Rad Fan ON. While reading the actual voltage...
Forum: Tech / General Engine
09-20-2006, 06:56 AM
Replies: 11
Views: 548
Posted By iroc monster

I do have an oscilloscope. Do I take the reading...

I do have an oscilloscope. Do I take the reading from the Bat terminal on the back of the alt? Then should I look for 3 DC phases or 3 half positive cycles coming out? I should also check the diode...
Forum: Tech / General Engine
09-18-2006, 10:53 PM
Replies: 11
Views: 548
Posted By iroc monster

I replaced the alt because my old one was...

I replaced the alt because my old one was whinning and thought it was the bearings. But while trying to take the pulley off to check the front bearings, the alt fell down off my vise and cracked on...
Forum: Tech / General Engine
09-15-2006, 11:14 PM
Replies: 230
Views: 46,742
Posted By iroc monster

That is a drop base Edelbrock 4207 air breather,...

That is a drop base Edelbrock 4207 air breather, but the 3" element raised it enough that the motor touched the hood and you could hear it rattle. With a 4" highrise intake, it only left me with only...
Forum: Tech / General Engine
09-14-2006, 10:39 PM
Replies: 230
Views: 46,742
Posted By iroc monster

Here's mine

I wanted a cold air induction system for a carburated engine and I wanted it all to fit under the hood, so I made my own.
Forum: Tech / General Engine
09-14-2006, 10:08 PM
Replies: 11
Views: 548
Posted By iroc monster

I didn't get the test light to go ON but I did...

I didn't get the test light to go ON but I did get my meter showing a 6.2mA draw. This of course was with the ACC fuse out, so no clock, no dome light or anything. Once I pulled the Hazard Light fuse...
Forum: Tech / General Engine
09-13-2006, 05:32 PM
Replies: 11
Views: 548
Posted By iroc monster

No I'm not load testing it, I'm just measuring it...

No I'm not load testing it, I'm just measuring it with a voltmeter.
My alternator makes the whining sound when I turn the lights ON or the rad fan is ON. The voltage drops from 14V to just below 12V...
Forum: Tech / General Engine
09-13-2006, 08:38 AM
Replies: 11
Views: 548
Posted By iroc monster

Battery Question

If a battery is charged up to 15V and the next morning that battery is down 12.7V. Is this the sign of a weakening battery?
Forum: Carburetors
09-22-2005, 01:47 PM
Replies: 17
Views: 1,252
Posted By iroc monster

I also tried everything. I have a Holley 750cfm...

I also tried everything. I have a Holley 750cfm sitting on a 4" intake and I've only got 1" clearance at the front of the carb.
I tried the smallest cleaner I could find from Mr.Gasket with a 1"...
Forum: Carburetors
09-22-2005, 07:23 AM
Replies: 4
Views: 557
Posted By iroc monster

I had the same problem. I got a 4" intake with a...

I had the same problem. I got a 4" intake with a 750cfm Holley and only had 1" left before touching the hood. I didn't want to cut out the hood for a hood scoop. I tried a small 1" element because...
Showing results 1 to 18 of 18


 
Forum Jump


All times are GMT -5. The time now is 01:22 PM.