A-arm fitment after installing poly bushings.
#1
Supreme Member
Thread Starter
iTrader: (4)
Join Date: Sep 2004
Location: MN
Posts: 2,069
Likes: 0
Received 3 Likes
on
3 Posts
Car: 85 SC, 86 Berlinetta
Engine: V6, V8
Transmission: 700r4, 700r4
A-arm fitment after installing poly bushings.
I'm having trouble installing a set of replacement A-arms which I had poly bushings (Energy suspension) installed. (My old ones rusted out.)
The A-arms fit as if they are too wide, but when I compare the old and new, the metal lines up perfectly.
The lip of the larger rear bushing including the metal and the poly is much thicker than the stock one which appears to be off-setting the A-arm.
Are both bushings supposed to be installed in the same direction? I noticed that the old ones were installed from rear to front, but the new ones are both facing in.
If the front bushing was was set in the same direction as the rear, it would line up the same, but I could allow it to be offset enough to fit. If I did do this, how would this affect alignment later on?
Should the rear lip of the larger (rear) bushing be reduced so that it matches the stock one?
I already evened out the inside surfaces of the K-member with a grinder, but was wondering how smooth the surface should be with the poly material rubbing against it.
Any help is appreciated
The A-arms fit as if they are too wide, but when I compare the old and new, the metal lines up perfectly.
The lip of the larger rear bushing including the metal and the poly is much thicker than the stock one which appears to be off-setting the A-arm.
Are both bushings supposed to be installed in the same direction? I noticed that the old ones were installed from rear to front, but the new ones are both facing in.
If the front bushing was was set in the same direction as the rear, it would line up the same, but I could allow it to be offset enough to fit. If I did do this, how would this affect alignment later on?
Should the rear lip of the larger (rear) bushing be reduced so that it matches the stock one?
I already evened out the inside surfaces of the K-member with a grinder, but was wondering how smooth the surface should be with the poly material rubbing against it.
Any help is appreciated
#3
Supreme Member
iTrader: (9)
I believe the bushings should face the same way as the originals did.One the the holes in the A-arms may be slightly larger than the other(i may be wrong though!).Also the bolts should face rearward.When i had the stock A-arms.I remember the energy install sheet mentioned this.You shouldnt have to hammer them in, but it is a tighter fit.The lube helps though.
#5
Supreme Member
iTrader: (1)
Join Date: Sep 2005
Posts: 26,112
Received 1,686 Likes
on
1,281 Posts
Car: Yes
Engine: Usually
Transmission: Sometimes
Axle/Gears: Behind me somewhere
Take your hammer and knock the control arm bushing bracket (on the "frame") apart, to "spread" it, so that the bushing will slip up in there. Much easier to put things together when they slip into place.
Tightening the bolt will re-compress it.
Tightening the bolt will re-compress it.
#6
Supreme Member
Thread Starter
iTrader: (4)
Join Date: Sep 2004
Location: MN
Posts: 2,069
Likes: 0
Received 3 Likes
on
3 Posts
Car: 85 SC, 86 Berlinetta
Engine: V6, V8
Transmission: 700r4, 700r4
Thanks for the input. The thing I'm concerned about is the gaps on the inside of the A-arm and bushings total around 1/4". This is a lot of space for the K-member flanges to move and I'm worried about the placement of the a-arm after doing this. I wouldn't have any issue if it was simply spreading them or working them in place a little.
Trending Topics
#8
Supreme Member
iTrader: (1)
Join Date: Jul 2004
Location: Calgary, AB, Canada
Posts: 10,763
Likes: 0
Received 4 Likes
on
4 Posts
Car: 1982 Trans-Am
Engine: 355 w/ ported 416s
Transmission: T10, hurst shifter
Axle/Gears: 10 bolt, true-trac, 3.73
just a side note; any place where the poly rubs metal, should be GOOPED with that nasty clear silicone grease. Gooped like crazy.
Thanks for the heads up BTW, i'm going to be putting my poly bushings in my a-arms and reinstalling them sometime in the near future here..
Thanks for the heads up BTW, i'm going to be putting my poly bushings in my a-arms and reinstalling them sometime in the near future here..
Thread
Thread Starter
Forum
Replies
Last Post
1992rs/ss
NW Indiana and South Chicago Suburb
12
05-19-2020 07:02 PM
1992rs/ss
Engine/Drivetrain/Suspension Parts for Sale
16
01-28-2016 09:58 PM
NBrehm
Engine/Drivetrain/Suspension Parts for Sale
0
08-05-2015 07:57 PM