Is a Roller Cam worth the cost?
#1
Supreme Member
Thread Starter
Join Date: Jan 2001
Location: Someone owes me 10,000 posts
Posts: 7,164
Likes: 0
Received 1 Like
on
1 Post
Car: 99 Formula
Engine: LS1
Transmission: T56
Axle/Gears: 342
Is a Roller Cam worth the cost?
I know running a roller cam will help free up some HP, but is it worth it? Is it easier to install than a hydraulic one as far as setting valve lash with hydraulic, how do you do that with a roller. How much would I be looking at including everything I would need?
#2
TGO Supporter
iTrader: (2)
it depends on the rest of your combo. If you've got a stock 305, then you're talking about a total waste of money. In my case, it may be necessary. If I slap a set of AFR heads on with a stealth ram, a hydraulic cam just won't be able to keep the valves open long enough to maximize the system's potential, so a roller retrofit will be quite beneficial.
#3
Supreme Member
Thread Starter
Join Date: Jan 2001
Location: Someone owes me 10,000 posts
Posts: 7,164
Likes: 0
Received 1 Like
on
1 Post
Car: 99 Formula
Engine: LS1
Transmission: T56
Axle/Gears: 342
Check my sig to see what I have, I plan on some head work, new intake and higher stall TC when I get a cam. The heads I have right now have 1.94/1.5 valves, I was told they just need some porting. I'm either gettin the Edelbrock EPS or RPM intake, and a TC around the 2500 stall area.
Last edited by Mark A Shields; 05-04-2002 at 09:41 PM.
#4
Member
I swear by 'em. roller cams get the lash set teh same way as flat tappet cams, the important part is hydraulic or solid. As a retrofit somewhere between 400 and 600 bucks, so it's pricey.
#6
TGO Supporter
iTrader: (2)
That block might have the bosses there that you need to install a stock roller retainer thingie. if that's the case, you should be able to get some used lifters and the holder relatively cheap, so it may be worth it. But if you've got to do a retrofit, I don't see where that motor is going to benefit more than 10, maybe 15 hp (that's just a guess) from using a good roller cam vs. a good hydraulic.
Trending Topics
#8
Supreme Member
I think he means dripped and tapped holes in the lifter valley for the spider retainer.
The roller cams have faster ramp speeds than flat tappets and in turn can make higher lifts.
Definitely more power and more rpm's.
The roller cams have faster ramp speeds than flat tappets and in turn can make higher lifts.
Definitely more power and more rpm's.
#9
Supreme Member
iTrader: (1)
Join Date: Jun 2001
Location: 600 yds out
Posts: 1,520
Likes: 0
Received 0 Likes
on
0 Posts
Car: Bee-Bowdy
Engine: blowd tree-fity
Transmission: sebin hunnerd
Axle/Gears: fo-tins
I think the roller cam is worth every penny. The roller cam can open the valve to maximum lift quicker. It can keep the valve at max lift for a longer duration.
Less friction is an added bonus. You don't have to break a roller cam in either...another bonus.
Less friction is an added bonus. You don't have to break a roller cam in either...another bonus.
Last edited by V8Astro Captain; 05-04-2002 at 10:19 PM.
Thread
Thread Starter
Forum
Replies
Last Post
junkcltr
Tech / General Engine
6
08-02-2019 11:12 PM
ambainb
Camaros for Sale
11
04-25-2016 09:21 PM
gixxer92
Engine/Drivetrain/Suspension Parts for Sale
5
09-01-2015 04:32 PM