Been getting vibrations?????
#1
Senior Member
Thread Starter
iTrader: (1)
Join Date: Feb 2008
Location: Waynesville ohio
Posts: 805
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 corvette Z51
Engine: L98
Transmission: doug nash 4+3 speed
Axle/Gears: 3:42 posi
Been getting vibrations?????
Ok guys i put in the 3:73s and about 75-80 it starts vibrating and gets worse faster you go? I like to cruize on the high way at 70-75 then when i have to make a move then it gets bad vibrations. I am hoping is that the 305 cant push it that far and hoping when i put the LT1 in it will go away to over 100. Or is my gears messed up?
thanks
kevin
thanks
kevin
#2
Re: Been getting vibrations?????
Ok guys i put in the 3:73s and about 75-80 it starts vibrating and gets worse faster you go? I like to cruize on the high way at 70-75 then when i have to make a move then it gets bad vibrations. I am hoping is that the 305 cant push it that far and hoping when i put the LT1 in it will go away to over 100. Or is my gears messed up?
thanks
kevin
thanks
kevin
#3
Supreme Member
Re: Been getting vibrations?????
Was the rearend taken out to change the gears or was it done while attached to the car.
#4
Senior Member
Thread Starter
iTrader: (1)
Join Date: Feb 2008
Location: Waynesville ohio
Posts: 805
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 corvette Z51
Engine: L98
Transmission: doug nash 4+3 speed
Axle/Gears: 3:42 posi
Re: Been getting vibrations?????
The gears was just done in the car. Nothing was removed or nothing.
#5
Member
Join Date: Jan 2008
Location: Austin, Texas
Posts: 218
Likes: 0
Received 0 Likes
on
0 Posts
Car: 86 iroc
Engine: 383HSR
Transmission: custom 700r
Axle/Gears: moser 9" 3.90
Re: Been getting vibrations?????
common problem when upgrading to higher numerical gear sets as the drive shaft from the factory was poorly ballanced. have your local driveline shop balance it and you should be good!
#7
Senior Member
Thread Starter
iTrader: (1)
Join Date: Feb 2008
Location: Waynesville ohio
Posts: 805
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 corvette Z51
Engine: L98
Transmission: doug nash 4+3 speed
Axle/Gears: 3:42 posi
Re: Been getting vibrations?????
The drive shaft was removed they put new end things i forget wat their called the u joint! then eveything but the axels were replaced.
kevin
kevin
Trending Topics
#9
Senior Member
Thread Starter
iTrader: (1)
Join Date: Feb 2008
Location: Waynesville ohio
Posts: 805
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1986 corvette Z51
Engine: L98
Transmission: doug nash 4+3 speed
Axle/Gears: 3:42 posi
Re: Been getting vibrations?????
I hope thats it! that shouldnt cost a hole lot? Who can fix it?
kevin
kevin
Last edited by GoodlookinRS; 02-11-2009 at 07:48 PM.
Thread
Thread Starter
Forum
Replies
Last Post
roysatikas
Transmissions and Drivetrain
0
09-22-2015 08:15 PM