ls1 driveshaft questions
#1
Supreme Member
Thread Starter
iTrader: (4)
Join Date: Aug 2004
Location: southern maryland
Posts: 1,417
Likes: 0
Received 0 Likes
on
0 Posts
Car: 2012 Ram express
Engine: 5.7 hemi
Transmission: auto
Axle/Gears: 3.55
ls1 driveshaft questions
how many weights are on a ls1 driveshaft? I just got one and making sure everything is good before i install it. theres a sticker on the shaft with this number 12564004 is this the right one?
#2
Supreme Member
Join Date: Mar 2003
Location: Florida
Posts: 4,771
Likes: 0
Received 14 Likes
on
10 Posts
Car: 1987 Black IROC-Z (SOLD)
Re: ls1 driveshaft questions
Weights?? Depends if it needed balanced. I don't have the p/n but if it is a LSi 3" dia aluminum dr shaft there is only one the other is steel. Also it will fit any 3rd gen except some V6 cars.
#4
Supreme Member
Thread Starter
iTrader: (4)
Join Date: Aug 2004
Location: southern maryland
Posts: 1,417
Likes: 0
Received 0 Likes
on
0 Posts
Car: 2012 Ram express
Engine: 5.7 hemi
Transmission: auto
Axle/Gears: 3.55
Re: ls1 driveshaft questions
yeah im just making sure all the weights are on there. theres one on there making sure there isnt suppose to be more
#5
Junior Member
Join Date: Apr 2007
Location: Giathersburg, Maryland
Posts: 98
Likes: 0
Received 0 Likes
on
0 Posts
Car: 1987 Z28
Engine: 355
Transmission: 700r4
Axle/Gears: 3.42
Re: ls1 driveshaft questions
one way to find out is to put it in and c how it feels. Its not hard to swap a driveshaft it takes what 10 to 15 min and 4 bolts
#6
Moderator
iTrader: (5)
Re: ls1 driveshaft questions
If a weight is missing, you'll see where it was located on the d/s. My experience with JG1 shafts was that there was always one or two weights. Though I had 60+ of these in my possession at one time or another, I only remember a couple that had missing weights. If I were guessing (and I am), I'd say you were good to go.
JamesC
JamesC
#7
Supreme Member
Thread Starter
iTrader: (4)
Join Date: Aug 2004
Location: southern maryland
Posts: 1,417
Likes: 0
Received 0 Likes
on
0 Posts
Car: 2012 Ram express
Engine: 5.7 hemi
Transmission: auto
Axle/Gears: 3.55
Re: ls1 driveshaft questions
anybody kno how to knock the u joints out of these driveshafts they have the plastic stick threw them the steel driveshafts i heat them to get the ujoints out not sure if i can do the same to aluminum
Trending Topics
#8
Supreme Member
iTrader: (4)
Join Date: Aug 2005
Location: louisville, ky
Posts: 1,366
Likes: 0
Received 0 Likes
on
0 Posts
Axle/Gears: '01 3.42 10 bolt
Re: ls1 driveshaft questions
they are too short for the early 200c and the 4 speeds. the t-5 and the 700r4 they will fit. v6 or v8 doesn't matter.
you use a torch to melt the plastic like you do the steel ones.
#9
Re: ls1 driveshaft questions
I have a 1990 IROC-Z with the 5.7 motor, 700r tran. and the 9 bolt borgwarner rear end. I have a aluminum drive shaft with a three rivers sticker on it with a part #12564004 will it fit my car?
Thread
Thread Starter
Forum
Replies
Last Post
ambainb
Camaros for Sale
11
04-25-2016 09:21 PM