Need your opinions!!!
Thread Starter
Junior Member
Joined: Jul 2003
Posts: 80
Likes: 0
From: Belleville
Car: 88 Trans Am GTA
Engine: 350 TPI
Transmission: 700R4
Need your opinions!!!
I am ready to get a new hood for my GTA! I have a problem making up my mind
. I am going either with a ram air II or a cowl hood for clearence when I install an HSR. Tell me what you guys think! The pic of the ram air II is actually photoshoped onto my car, and the cowl is on a different car.
. I am going either with a ram air II or a cowl hood for clearence when I install an HSR. Tell me what you guys think! The pic of the ram air II is actually photoshoped onto my car, and the cowl is on a different car. Member
Joined: May 2002
Posts: 432
Likes: 0
From: SE Pennsylvania
Car: 1986 Trans Am
Engine: 350 W/Plenty of Mods
Transmission: T5
Well, I have the RAII hood, I love the looks of it, but that is a really nice cowl hood also. Honestly though, it dosn't matter who likes what, because everyone has different tastes and opinions, and when it comes to your car, you should just go with your initial instict and preference, cuz even if other people don't like a certian hood, others will, and if you have the one you like then you know your car looks just how YOU want it to.
Trending Topics
Senior Member
Joined: May 2003
Posts: 663
Likes: 1
From: Runnin' from the Reaper
Car: 91 B4C/91 RS 305
Engine: L98 and L03
Transmission: 2xTH700R4
Axle/Gears: 3.23 LSD/2.73 Open
Originally posted by 91-RED-WS6
4" is WAY too big.
4" is WAY too big.
Wussy
I hate the RAII hoods too
I say cowl
Last edited by darkhorse91; Jul 28, 2003 at 04:10 AM.
Member
Joined: Jun 2003
Posts: 266
Likes: 0
From: Ohio, USA
Car: '92 Camaro RS, '93 Ranger
Engine: LO3, Vulcan
Transmission: 700R4, M5OD
Axle/Gears: 2.73, 3.45
I vote for cowl. I don't really care for the RAIIs, they don't seem to match Firebirds. They look like something off a Dodge truck or a minivan to me. What I think would make a Ram Air II look better would be to ditch or lessen the center line, and make the sides a bit boxier. Them things are just way too round for our nice semi-boxy thirdgens.
Senior Member
Joined: Jul 2001
Posts: 839
Likes: 0
From: Valley Head, AL
Car: 1983 Camaro "SC-350"
Engine: Mild 350 4-bolt
Transmission: 700R4 w/ TCI Stall
Originally posted by 91-RED-WS6
RA II looks like @ss IMO... RA I looks best. If you go with a cowl, keep it the low one (2.5 inch or something thereabouts)... 4" is WAY too big.
RA II looks like @ss IMO... RA I looks best. If you go with a cowl, keep it the low one (2.5 inch or something thereabouts)... 4" is WAY too big.
I think its perfect......
:hail: The contors, IMHO are too soft for the hard lines that define our cars. Don't get me wrong, RA on a 02 TA is insanely hot, but only because it matchs the body design. A well defined cowl, like the one pictured feels and looks much more natural on our cars.
However I'm a strong advocate of previously mentioned: Its your car... and everyone has and is entitled to their own opinion. However, I assumed you asked because you like both...
Suggestion: Get both hoods PSed onto your car. print them out @ the same size. set them up next to each other where they can be easily seen. go eat dinner (or something to stop thinking about it) Then walk back into the room and see which one you're drawn to first...
Good luck!
However I'm a strong advocate of previously mentioned: Its your car... and everyone has and is entitled to their own opinion. However, I assumed you asked because you like both...
Suggestion: Get both hoods PSed onto your car. print them out @ the same size. set them up next to each other where they can be easily seen. go eat dinner (or something to stop thinking about it) Then walk back into the room and see which one you're drawn to first...
Good luck!
Thread
Thread Starter
Forum
Replies
Last Post
Pac J
Tech / General Engine
3
May 17, 2020 10:44 AM
LiquidBlue
Wheels and Tires
32
Dec 10, 2019 04:06 PM
skinny z
Engine/Drivetrain/Suspension Parts for Sale
5
Oct 5, 2015 06:23 PM




